scholarly journals Recovery of Metals from Printed Circuit Boards By Means of Electrostatic Separation

2020 ◽  
Vol 28 (4) ◽  
pp. 213-219
Author(s):  
Dawid Franke ◽  
Tomasz Suponik ◽  
Paweł M. Nuckowski ◽  
Klaudiusz Gołombek ◽  
Kamila Hyra
Keyword(s):  
Waste Management ◽  
Printed Circuit Boards ◽  
Printed Circuit Board ◽  
New Technologies ◽  
Negative Impact ◽  
Electronic Waste ◽  
Circuit Board ◽  
Circuit Boards ◽  
Electrostatic Separation ◽  
Printed Circuit

AbstractWithout the use of appropriate recycling technologies, the growing amount of electronic waste in the world can be a threat to the development of new technologies, and in the case of improper waste management, may have a negative impact on the environment. This is due to the fact that this waste contains large amounts of valuable metals and toxic polymers. Therefore, it should be recycled in accordance with the assumptions of the circular economy. The methods of mechanical recovery of metals from electronic waste, including printed circuits, may be widely used in the future by waste management companies as well as metal production and processing companies. That is why, a well-known and easily applicable electrostatic separation (ES) method was used to recover metals from printed circuit boards. The grain class of 0.32 - 0.10 mm, obtained after grinding the boards, was fed to a separator. Feed and separation products were analyzed by means of ICP-AES, SEM/EDS and XRD. The concentrate yield obtained after electrostatic separation amounted to 32.3% of the feed. Its density was 11.1 g/cc. Out of the 91.44% elements identified in the concentrate, over 90% were metals. XRD, SEM observations and EDS analysis confirmed the presence of non-metallic materials in the concentrate. This relatively high content of impurities indicates the need to grind printed circuit board into grain classes smaller than 0.32-0.10 mm.

scholarly journals Use of gravity separation in metals concentration from printed circuit board scraps

2014 ◽  
Vol 67 (1) ◽  
pp. 73-79 ◽  
Author(s):  
Hugo Marcelo Veit ◽  
Nichele Cristina de Freitas Juchneski ◽  
Janine Scherer
Keyword(s):  
Printed Circuit Boards ◽  
Printed Circuit Board ◽  
Electronic Waste ◽  
Economic Value ◽  
Circuit Board ◽  
Environmental Damage ◽  
Circuit Boards ◽  
New Materials ◽  
Printed Circuit ◽  
Complex Process

The amount of solid waste generated by all segments of society has increased in past decades. Annually, in Brazil, 96,000 tonnes of electronic scrap are generated from computers. The incorrect disposal of this waste creates environmental damage, generating loss of materials that could be reused and / or recycled, reducing the extraction of recyclable materials to produce new materials. The printed circuit boards (PCB) represent approximately 30% of the electronic waste generated and its recycling is a complex process, but very important for the recovery of metals of high economic value. Industrial processes for the recovery of metals from PCB are based on pyrometallurgy and hydrometallurgy. In both cases, it is possible to carry out a pretreatment that involves the use of mechanical processes. Therefore, for this paper, the concentration of the metallic fraction of PCB through the use of a Mozley concentrator was enabled. The results show that it is possible to obtain significant quantities of metals such as copper (concentration 85%), tin (95%), and silver (98%) in the fractions of interest.

Dielectric Breakdown in Printed Circuit Boards at Elevated Temperatures

1996 ◽  
Author(s):  
P. Singh ◽  
G.T. Galyon ◽  
J. Obrzut ◽  
W.A. Alpaugh
Keyword(s):  
Experimental Data ◽  
Thermal Degradation ◽  
Printed Circuit Boards ◽  
Printed Circuit Board ◽  
Elevated Temperatures ◽  
Dielectric Breakdown ◽  
Circuit Board ◽  
Circuit Boards ◽  
Printed Circuit ◽  
Data Matching

Abstract A time delayed dielectric breakdown in printed circuit boards, operating at temperatures below the epoxy resin insulation thermo-electrical limits, is reported. The safe temperature-voltage operating regime was estimated and related to the glass-rubber transition (To) of printed circuit board dielectric. The TG was measured using DSC and compared with that determined from electrical conductivity of the laminate in the glassy and rubbery state. A failure model was developed and fitted to the experimental data matching a localized thermal degradation of the dielectric and time dependency. The model is based on localized heating of an insulation resistance defect that under certain voltage bias can exceed the TG, thus, initiating thermal degradation of the resin. The model agrees well with the experimental data and indicates that the failure rate and truncation time beyond which the probability of failure becomes insignificant, decreases with increasing glass-rubber transition temperature.

scholarly journals Estimating Recycling Return of Integrated Circuits Using Computer Vision on Printed Circuit Boards

2021 ◽  
Vol 11 (6) ◽  
pp. 2808
Author(s):  
Leandro H. de S. Silva ◽  
Agostinho A. F. Júnior ◽  
George O. A. Azevedo ◽  
Sergio C. Oliveira ◽  
Bruno J. T. Fernandes
Keyword(s):  
Integrated Circuits ◽  
Printed Circuit Boards ◽  
Printed Circuit Board ◽  
Electronic Waste ◽  
Decision Criterion ◽  
Economic Feasibility ◽  
Electronic Equipment ◽  
Circuit Board ◽  
Mechanical Recycling ◽  
Printed Circuit

The technological growth of the last decades has brought many improvements in daily life, but also concerns on how to deal with electronic waste. Electrical and electronic equipment waste is the fastest-growing rate in the industrialized world. One of the elements of electronic equipment is the printed circuit board (PCB) and almost every electronic equipment has a PCB inside it. While waste PCB (WPCB) recycling may result in the recovery of potentially precious materials and the reuse of some components, it is a challenging task because its composition diversity requires a cautious pre-processing stage to achieve optimal recycling outcomes. Our research focused on proposing a method to evaluate the economic feasibility of recycling integrated circuits (ICs) from WPCB. The proposed method can help decide whether to dismantle a separate WPCB before the physical or mechanical recycling process and consists of estimating the IC area from a WPCB, calculating the IC’s weight using surface density, and estimating how much metal can be recovered by recycling those ICs. To estimate the IC area in a WPCB, we used a state-of-the-art object detection deep learning model (YOLO) and the PCB DSLR image dataset to detect the WPCB’s ICs. Regarding IC detection, the best result was obtained with the partitioned analysis of each image through a sliding window, thus creating new images of smaller dimensions, reaching 86.77% mAP. As a final result, we estimate that the Deep PCB Dataset has a total of 1079.18 g of ICs, from which it would be possible to recover at least 909.94 g of metals and silicon elements from all WPCBs’ ICs. Since there is a high variability in the compositions of WPCBs, it is possible to calculate the gross income for each WPCB and use it as a decision criterion for the type of pre-processing.

Evaluation of new technologies and materials for printed circuit boards with improved heat dissipation properties

Circuit World ◽  
2016 ◽  
Vol 42 (1) ◽  
pp. 32-36 ◽  
Author(s):  
Michal Baszynski ◽  
Edward Ramotowski ◽  
Dariusz Ostaszewski ◽  
Tomasz Klej ◽  
Mariusz Wojcik ◽  
...  
Keyword(s):  
Thermal Properties ◽  
Printed Circuit Boards ◽  
Heat Dissipation ◽  
Printed Circuit Board ◽  
New Technologies ◽  
Electronic Device ◽  
Circuit Board ◽  
New Materials ◽  
Content Type ◽  
Printed Circuit

Purpose – The purpose of this paper is to evaluate thermal properties of printed circuit board (PCB) made with use of new materials and technologies. Design/methodology/approach – Four PCBs with the same layout but made with use of different materials and technologies have been investigated using thermal camera to compare their thermal properties. Findings – The results show how important the thermal properties of PCBs are for providing effective heat dissipation, and how a simple alteration to the design can help to improve the thermal performance of electronic device. Proper layout, new materials and technologies of PCB manufacturing can significantly reduce the temperature of electronic components resulting in higher reliability of electronic and power electronic devices. Originality/value – This paper shows the advantages of new technologies and materials in PCB thermal management.

scholarly journals A model for the reflection of terahertz signals from printed circuit board surfaces

2018 ◽  
Vol 10 (2) ◽  
pp. 179-186 ◽  
Author(s):  
Alexander Fricke ◽  
Mounir Achir ◽  
Philippe Le Bars ◽  
Thomas Kürner
Keyword(s):  
Printed Circuit Boards ◽  
Printed Circuit Board ◽  
Simulated Annealing Algorithm ◽  
Specular Reflection ◽  
Circuit Board ◽  
Network Analyzer ◽  
Circuit Boards ◽  
Printed Circuit ◽  
Propagation Modeling ◽  
Annealing Algorithm

AbstractBased on vector network analyzer Measurements, a model for the specular reflection behavior of printed circuit boards in the Terahertz range has been derived. It has been calibrated to suit the behavior of the measurements using a simulated annealing algorithm. The model has been tailored for integration to ray-tracing-based propagation modeling.

scholarly journals NotchPUF: Printed Circuit Board PUF Based on Microstrip Notch Filter

Cryptography ◽  
2020 ◽  
Vol 4 (2) ◽  
pp. 11
Author(s):  
Mitchell Martin ◽  
Jim Plusquellic
Keyword(s):  
Printed Circuit Boards ◽  
Printed Circuit Board ◽  
Statistical Tests ◽  
Notch Filter ◽  
Circuit Board ◽  
Circuit Boards ◽  
Printed Circuit ◽  
In Series ◽  
Commercial Off The Shelf ◽  
Using Data

Physical Unclonable Functions (PUFs) are primitives that are designed to leverage naturally occurring variations to produce a random bitstring. Current PUF designs are typically implemented in silicon or utilize variations found in commercial off-the-shelf (COTS) parts. Because of this, existing designs are insufficient for the authentication of Printed Circuit Boards (PCBs). In this paper, we propose a novel PUF design that leverages board variations in a manufactured PCB to generate unique and stable IDs for each PCB. In particular, a single copper trace is used as a source of randomness for bitstring generation. The trace connects three notch filter structures in series, each of which is designed to reject specific but separate frequencies. The bitstrings generated using data measured from a set of PCBs are analyzed using statistical tests to illustrate that high levels of uniqueness and randomness are achievable.

Downsizing an automotive junction box based on large current-carrying printed-circuit board optimization

2016 ◽  
Vol 231 (2) ◽  
pp. 267-278 ◽  
Author(s):  
Hansang Lim ◽  
Do-Hwan Jung ◽  
Geono Kwon ◽  
Young Jong Lee ◽  
Jun Seo Park
Keyword(s):  
Power Distribution ◽  
Printed Circuit Boards ◽  
Printed Circuit Board ◽  
Circuit Board ◽  
Installation Space ◽  
Circuit Boards ◽  
Printed Circuit ◽  
Overcurrent Protection ◽  
Large Current ◽  
Analytical Estimation

An automotive junction box distributes electric power to electric systems installed in a vehicle with overcurrent protection. As a larger number of electric systems are installed, the junction box is equipped with more components, functionalities and connections. However, owing to the fuse accessibility, its installation space is so restricted that a downsized design is required for the junction box. The junction box is composed of small signal circuitry for control and monitoring, and large current-carrying circuitry for power distribution which includes many parallel traces. Because of these unique features, widely used techniques for downsizing printed-circuit boards are not applicable. Also, there is no rule for designing large current-carrying parallel traces, and it is difficult to optimize the size of the printed-circuit board for the automotive junction box. This paper presents the design rules for a printed-circuit board when downsizing a junction box. First, the layout strategy for the power distribution components is presented, which is determined by the sum of the squares of the currents flowing through connector pairs. Then, the thermal effects of parallel traces are simulated for different conditions by using thermal analysis software. Based on the results, an analytical estimation of the additional temperature rises due to parallel traces and rules for a thermally effective arrangement of the parallel traces are presented.

Future paper based printed circuit boards for green electronics: fabrication and life cycle assessment

2014 ◽  
Vol 7 (11) ◽  
pp. 3674-3682 ◽  
Author(s):  
Jingping Liu ◽  
Cheng Yang ◽  
Haoyi Wu ◽  
Ziyin Lin ◽  
Zhexu Zhang ◽  
...  
Keyword(s):  
Life Cycle Assessment ◽  
Life Cycle ◽  
Environmental Impact ◽  
Printed Circuit Boards ◽  
Printed Circuit Board ◽  
Circuit Board ◽  
Circuit Boards ◽  
Printed Circuit ◽  
Future Paper ◽  
Printing Paper

A multilayer printed circuit board (PCB) can be fabricated using commercially available printing paper, which shows comparable functionalities with the conventional organic PCBs but 100 times lower environmental impact.

New technologies of multi-layered printed circuit boards, intended of rapid-design electronic modules

Circuit World ◽  
2015 ◽  
Vol 41 (3) ◽  
pp. 121-124
Author(s):  
Wojciech Stęplewski ◽  
Mateusz Mroczkowski ◽  
Radoslav Darakchiev ◽  
Konrad Futera ◽  
Grażyna Kozioł
Keyword(s):  
Printed Circuit Boards ◽  
New Technologies ◽  
Circuit Board ◽  
Circuit Boards ◽  
Content Type ◽  
Signal Distribution ◽  
Printed Circuit ◽  
Rapid Design ◽  
Small Pitch ◽  
Signal Path

Purpose – The purpose of this study was the use of embedded components technology and innovative concepts of the printed circuit board (PCB) for electronic modules containing field-programmable gate array (FPGA) devices with a large number of pins (e.g. Virtex 6, FF1156/RF1156 package, 1,156 pins). Design/methodology/approach – In the multi-layered boards, embedded passive components that support FPGA device input/output (I/O), such as blocking capacitors and pull-up resistors, were used. These modules can be used in rapid design of electronic devices. In the study, the MC16T FaradFlex material was used for the inner capacitive layer. The Ohmega-Ply RCM 25 Ω/sq material was used to manufacture pull-up resistors for high-frequency pins. The embedded components have been connected to pins of the FPGA component by using plated-through holes for capacitors and blind vias for resistors. Also, a technique for a board-to-board joining, by using castellated terminations, is described. Findings – The fully functional modules for assembly of the FPGA were manufactured. Achieved resistance of embedded micro resistors, as small as the smallest currently used surface-mount device components (01005), was below required tolerance of 10 per cent. Obtained tolerance of capacitors was less than 3 per cent. Use of embedded components allowed to replace the pull-up resistors and blocking capacitors and shortens the signal path from the I/O of the FPGA. Correct connection to the castellated terminations with a very small pitch was also obtained. This allows in further planned studies to create a full signal distribution system from the FPGA without the use of unreliable plug connectors in aviation and space technology. Originality/value – This study developed and manufactured several innovative concepts of signal distribution from printed circuit boards. The signal distribution solutions were integrated with embedded components, which allowed for significant reduction in the signal path. This study allows us to build the target object that is the module for rapid design of the FPGA device. Usage of a pre-designed module would lessen the time needed to develop a FPGA-based device, as a significant part of the necessary work (mainly designing the signal and power fan-out) will already be done during the module development.

Sign in / Sign up

Export Citation Format

Share Document