Closed-cell foams produced from sputter-deposited aluminum

1977 ◽  
Author(s):  
J. PATTEN ◽  
E. GREENWELL
Keyword(s):  
Closed Cell ◽  
Sputter Deposited

Crystal Structure Analysis of Cu-Zr Alloys by Convergent Beam Diffraction

1981 ◽  
Vol 39 ◽  
pp. 354-355
Author(s):  
A. F. Marshall ◽  
J. W. Steeds ◽  
D. Bouchet ◽  
S. L. Shinde ◽  
R. G. Walmsley
Keyword(s):  
Crystal Structure ◽  
Point Group ◽  
Intermetallic Phase ◽  
Three Dimensional ◽  
Crystal Structure Analysis ◽  
Ion Milling ◽  
Composition And Structure ◽  
Unit Cells ◽  
Sputter Deposited ◽  
Convergent Beam

Convergent beam electron diffraction is a powerful technique for determining the crystal structure of a material in TEM. In this paper we have applied it to the study of the intermetallic phases in the Cu-rich end of the Cu-Zr system. These phases are highly ordered. Their composition and structure has been previously studied by microprobe and x-ray diffraction with sometimes conflicting results.The crystalline phases were obtained by annealing amorphous sputter-deposited Cu-Zr. Specimens were thinned for TEM by ion milling and observed in a Philips EM 400. Due to the large unit cells involved, a small convergence angle of diffraction was used; however, the three-dimensional lattice and symmetry information of convergent beam microdiffraction patterns is still present. The results are as follows:1) 21 at% Zr in Cu: annealed at 500°C for 5 hours. An intermetallic phase, Cu3.6Zr (21.7% Zr), space group P6/m has been proposed near this composition (2). The major phase of our annealed material was hexagonal with a point group determined as 6/m.

Characterization of reactive phase formation in sputter-deposited Ni/Al multilayer thin films using TEM

1996 ◽  
Vol 54 ◽  
pp. 1000-1001
Author(s):  
G. Lucadamo ◽  
K. Barmak ◽  
C. Michaelsen
Keyword(s):  
Thin Films ◽  
Phase Formation ◽  
Dark Field ◽  
Nickel Layer ◽  
Multilayer Thin Films ◽  
Cross Sectional ◽  
Dark Field Imaging ◽  
Transmission Electron ◽  
Sputter Deposited ◽  
Constant Heating

The subject of reactive phase formation in multilayer thin films of varying periodicity has stimulated much research over the past few years. Recent studies have sought to understand the reactions that occur during the annealing of Ni/Al multilayers. Dark field imaging from transmission electron microscopy (TEM) studies in conjunction with in situ x-ray diffraction measurements, and calorimetry experiments (isothermal and constant heating rate), have yielded new insights into the sequence of phases that occur during annealing and the evolution of their microstructure.In this paper we report on reactive phase formation in sputter-deposited lNi:3Al multilayer thin films with a periodicity A (the combined thickness of an aluminum and nickel layer) from 2.5 to 320 nm. A cross-sectional TEM micrograph of an as-deposited film with a periodicity of 10 nm is shown in figure 1. This image shows diffraction contrast from the Ni grains and occasionally from the Al grains in their respective layers.

TEM studies of solid-state reactions in sputter-deposited Nb/Al multilayer thin films

1996 ◽  
Vol 54 ◽  
pp. 1020-1021
Author(s):  
F. Ma ◽  
S. Vivekanand ◽  
K. Barmak ◽  
C. Michaelsen
Keyword(s):  
Thin Films ◽  
Solid State ◽  
Stoichiometric Composition ◽  
Analytical Electron Microscopy ◽  
Grain Structure ◽  
Solid State Reactions ◽  
Multilayer Thin Films ◽  
X Ray Diffraction ◽  
X Ray ◽  
Sputter Deposited

Solid state reactions in sputter-deposited Nb/Al multilayer thin films have been studied by transmission and analytical electron microscopy (TEM/AEM), differential scanning calorimetry (DSC) and X-ray diffraction (XRD). The Nb/Al multilayer thin films for TEM studies were sputter-deposited on (1102)sapphire substrates. The periodicity of the films is in the range 10-500 nm. The overall composition of the films are 1/3, 2/1, and 3/1 Nb/Al, corresponding to the stoichiometric composition of the three intermetallic phases in this system.Figure 1 is a TEM micrograph of an as-deposited film with periodicity A = dA1 + dNb = 72 nm, where d's are layer thicknesses. The polycrystalline nature of the Al and Nb layers with their columnar grain structure is evident in the figure. Both Nb and Al layers exhibit crystallographic texture, with the electron diffraction pattern for this film showing stronger diffraction spots in the direction normal to the multilayer. The X-ray diffraction patterns of all films are dominated by the Al(l 11) and Nb(l 10) peaks and show a merging of these two peaks with decreasing periodicity.

Microstructure of sputter deposited Ni-Sb ohmic contacts on GaAs

1989 ◽  
Vol 47 ◽  
pp. 450-451
Author(s):  
S. Yegnasubramanian ◽  
V.C. Kannan ◽  
R. Dutto ◽  
P.J. Sakach
Keyword(s):  
High Performance ◽  
Ohmic Contacts ◽  
Surface Defects ◽  
Pure Metal ◽  
Device Fabrication ◽  
Native Oxide ◽  
Metal Thin Films ◽  
Recent Developments ◽  
Different Temperatures ◽  
Sputter Deposited

Recent developments in the fabrication of high performance GaAs devices impose crucial requirements of low resistance ohmic contacts with excellent contact properties such as, thermal stability, contact resistivity, contact depth, Schottky barrier height etc. The nature of the interface plays an important role in the stability of the contacts due to problems associated with interdiffusion and compound formation at the interface during device fabrication. Contacts of pure metal thin films on GaAs are not desirable due to the presence of the native oxide and surface defects at the interface. Nickel has been used as a contact metal on GaAs and has been found to be reactive at low temperatures. Formation Of Ni2 GaAs at 200 - 350C is reported and is found to grow epitaxially on (001) and on (111) GaAs, but is shown to be unstable at 450C. This paper reports the investigations carried out to understand the microstructure, nature of the interface and composition of sputter deposited and annealed (at different temperatures) Ni-Sb ohmic contacts on GaAs by TEM. Attempts were made to correlate the electrical properties of the films such as the sheet resistance and contact resistance, with the microstructure. The observations are corroborated by Scanning Auger Microprobe (SAM) investigations.

The reaction of amorphous Ni-Nb films with Si in the presence of a native SiO2 layer

1990 ◽  
Vol 48 (4) ◽  
pp. 664-665
Author(s):  
N. Rozhanski ◽  
A. Barg
Keyword(s):  
High Temperature ◽  
Crystallization Temperature ◽  
Diffusion Barriers ◽  
Sio2 Layer ◽  
Si Substrate ◽  
Cross Sectional ◽  
Plan View ◽  
Temperature Range ◽  
Sputter Deposited

Amorphous Ni-Nb alloys are of potential interest as diffusion barriers for high temperature metallization for VLSI. In the present work amorphous Ni-Nb films were sputter deposited on Si(100) and their interaction with a substrate was studied in the temperature range (200-700)°C. The crystallization of films was observed on the plan-view specimens heated in-situ in Philips-400ST microscope. Cross-sectional objects were prepared to study the structure of interfaces.The crystallization temperature of Ni5 0 Ni5 0 and Ni8 0 Nb2 0 films was found to be equal to 675°C and 525°C correspondingly. The crystallization of Ni5 0 Ni5 0 films is followed by the formation of Ni6Nb7 and Ni3Nb nucleus. Ni8 0Nb2 0 films crystallise with the formation of Ni and Ni3Nb crystals. No interaction of both films with Si substrate was observed on plan-view specimens up to 700°C, that is due to the barrier action of the native SiO2 layer.

Transformation and Deformation Behavior in Sputter-Deposited Ti-Ni-Cu Thin Films

1995 ◽  
Vol 05 (C8) ◽  
pp. C8-689-C8-694 ◽  
Author(s):  
T. Hashinaga ◽  
S. Miyazaki ◽  
T. Ueki ◽  
H. Horikawa
Keyword(s):  
Thin Films ◽  
Deformation Behavior ◽  
Sputter Deposited

The Correlation of Adhesion Strength with Barrier Structure in Cu Metallization

2003 ◽  
Vol 766 ◽  
Author(s):  
A. Sekiguchi ◽  
J. Koike ◽  
K. Ueoka ◽  
J. Ye ◽  
H. Okamura ◽  
...  
Keyword(s):  
Thin Films ◽  
Adhesion Strength ◽  
Nitrogen Concentration ◽  
Scratch Test ◽  
Barrier Structure ◽  
Barrier Layers ◽  
Cu Metallization ◽  
Microstructure Observation ◽  
Sputter Deposited ◽  
Sulfur Containing

AbstractAdhesion strength in sputter-deposited Cu thin films on various types of barrier layers was investigated by scratch test. The barrier layers were Ta1-xNx with varied nitrogen concentration of 0, 0.2, 0.3, and 0.5. Microstructure observation by TEM indicated that each layer consists of mixed phases of β;-Ta, bcc-TaN0.1, hexagonal-TaN, and fcc-TaN, depending on the nitrogen concentration. A sulfur- containing amorphous phase was also present discontinuously at the Cu/barrier interfaces in all samples. Scratch test showed that delamination occurred at the Cu/barrier interface and that the overall adhesion strength increased with increasing the nitrogen concentration. A good correlation was found between the measured adhesion strength and the composing phases in the barrier layer.

Sign in / Sign up

Export Citation Format

Share Document