A parametric study of the effects of unsteady wake passing on the flow field in a compressor cascade

1996 ◽  
Author(s):  
Daniel Dorney ◽  
Aaron Mosebach ◽  
Douglas Sondak ◽  
Mark Barnett
Keyword(s):  
Flow Field ◽  
Parametric Study ◽  
Compressor Cascade ◽  
Unsteady Wake ◽  
Wake Passing

Numerical Investigation of Intermittent Corner Separation in a Linear Compressor Cascade

2016 ◽  
Author(s):  
Wei Ma ◽  
Feng Gao ◽  
Xavier Ottavy ◽  
Lipeng Lu ◽  
A. J. Wang
Keyword(s):  
Flow Field ◽  
Large Scale ◽  
Leading Edge ◽  
Suction Side ◽  
Detached Eddy Simulation ◽  
Compressor Cascade ◽  
Linear Compressor ◽  
Corner Separation ◽  
Eddy Simulation ◽  
Linear Compressor Cascade

Recently bimodal phenomenon in corner separation has been found by Ma et al. (Experiments in Fluids, 2013, doi:10.1007/s00348-013-1546-y). Through detailed and accurate experimental results of the velocity flow field in a linear compressor cascade, they discovered two aperiodic modes exist in the corner separation of the compressor cascade. This phenomenon reflects the flow in corner separation is high intermittent, and large-scale coherent structures corresponding to two modes exist in the flow field of corner separation. However the generation mechanism of the bimodal phenomenon in corner separation is still unclear and thus needs to be studied further. In order to obtain instantaneous flow field with different unsteadiness and thus to analyse the mechanisms of bimodal phenomenon in corner separation, in this paper detached-eddy simulation (DES) is used to simulate the flow field in the linear compressor cascade where bimodal phenomenon has been found in previous experiment. DES in this paper successfully captures the bimodal phenomenon in the linear compressor cascade found in experiment, including the locations of bimodal points and the development of bimodal points along a line that normal to the blade suction side. We infer that the bimodal phenomenon in the corner separation is induced by the strong interaction between the following two facts. The first is the unsteady upstream flow nearby the leading edge whose angle and magnitude fluctuate simultaneously and significantly. The second is the high unsteady separation in the corner region.

Experimental Investigation Into the Effects of the Steady Wake-Tip Clearance Vortex Interaction in a Compressor Cascade

2015 ◽  
Vol 137 (6) ◽  
Author(s):  
Andreas Krug ◽  
Peter Busse ◽  
Konrad Vogeler
Keyword(s):  
Flow Field ◽  
Experimental Studies ◽  
Axial Compressor ◽  
Field Measurements ◽  
Tip Clearance ◽  
Compressor Cascade ◽  
Unsteady Interaction ◽  
Linear Compressor Cascade ◽  
Tip Clearance Vortex ◽  
The Impact

An important aspect of the aerodynamic flow field in the tip region of axial compressor rotors is the unsteady interaction between the tip clearance vortex (TCV) and the incoming stator wakes. In order to gain an improved understanding of the mechanics involved, systematic studies need to be performed. As a first step toward the characterization of the dynamic effects caused by the relative movement of the blade rows, the impact of a stationary wake-induced inlet disturbance on a linear compressor cascade with tip clearance will be analyzed. The wakes were generated by a fixed grid of cylindrical bars with variable pitch being placed at discrete pitchwise positions. This paper focuses on experimental studies conducted at the newly designed low-speed cascade wind tunnel in Dresden. The general tunnel configuration and details on the specific cascade setup will be presented. Steady state flow field measurements were carried out using five-hole probe traverses up- and downstream of the cascade and accompanied by static wall pressure readings. 2D-particle image velocimetry (PIV) measurements complemented these results by visualizing the blade-to-blade flow field. Hence, the structure of the evolving secondary flow system is evaluated and compared for all tested configurations.

The Effect of Four Part Gap Geometry Configurations for Variable Stator Vanes in a Compressor Cascade

2012 ◽  
Author(s):  
Marcel Gottschall ◽  
Konrad Vogeler ◽  
Ronald Mailach
Keyword(s):  
Flow Field ◽  
Separated Flow ◽  
Reynolds Numbers ◽  
Compressor Cascade ◽  
Field Development ◽  
Operating Range ◽  
Rear Part ◽  
Axis Position ◽  
Stagger Angle ◽  
Variable Stator

The article describes numerical investigations on the influence of four different endwall clearance topologies for variable stator vanes to secondary flow field development and the performance of high pressure compressors. The aim of this work is to quantify the characteristics of different clearance configurations depending on the penny-axis position and the penny diameter for a typical operating range. All clearance configurations were implemented to a linear cascade of modern stator profiles. The analysis was introduced using a relative clearance size of 1.3% chord at three stagger angles and two characteristic Reynolds numbers to model the operating range on aircraft engines. 3D numerical calculations were carried out to gain information about the flow field inside the cascade. They were compared with measurements of a 5-hole-probe as well as pressure tappings on the airfoil and the endwall. The CFD shows the clearance characteristics in good agreement with the measurements for the lower and the nominal stagger angle. Small gaps in the rear part of the vane have a beneficial effect on the flow field. In contrast, a clearance in the higher loaded front part of the vane always resulted in increased losses. Otherwise, the significant enhanced performance of a rear part gap, which was measured at the higher stagger angle, was not reflected by the CFD. The reduced mixing losses and the higher averaged flow turning even compared to a configuration without a clearance are not verified with the calculations. Large flow separations at the high stagger angle result in a two to four times higher underturning of the CFD in comparison to the experiments. The clearance effects to the characteristic radial loss distribution up to 40 % bladeheight also deviate from the measurements due to heavy mixing of clearance and reversed separated flow.

Experimental Investigations on the Efficiency of Active Flow Control in a Compressor Cascade With Periodic Non-Steady Outflow Conditions

2017 ◽  
Author(s):  
Marcel Staats ◽  
Wolfgang Nitsche
Keyword(s):  
Flow Field ◽  
Flow Control ◽  
Flow Separation ◽  
Active Flow Control ◽  
Experimental Investigations ◽  
Compressor Cascade ◽  
Steady Regime ◽  
Stator Blade ◽  
Active Flow ◽  
The Impact

We present results of experiments on a periodically unsteady compressor stator flow of the type which would be expected in consequence of pulsed combustion. A Reynolds number of Re = 600000 was used for the investigations. The experiments were conducted on the two-dimensional low-speed compressor testing facility in Berlin. A choking device downstream the trailing edges induced a periodic non-steady outflow condition to each stator vane which simulated the impact of a pressure gaining combuster downstream from the last stator. The Strouhal number of the periodic disturbance was Sr = 0.03 w.r.t. the stator chord length. Due to the periodic non-steady outflow condition, the flow-field suffers from periodic flow separation phenomena, which were managed by means of active flow control. In our case, active control of the corner separation was applied using fluidic actuators based on the principle of fluidic amplification. The flow separation on the centre region of the stator blade was suppressed by means of a fluidic blade actuator leading to an overall time-averaged loss reduction of 11.5%, increasing the static pressure recovery by 6.8% while operating in the non-steady regime. Pressure measurements on the stator blade and the wake as well as PIV data proved the beneficial effect of the active flow control application to the flow field and the improvement of the compressor characteristics. The actuation efficiency was evaluated by two figures of merit introduced in this contribution.

scholarly journals Three-Dimensional Wake Decay Inside of a Compressor Cascade and its Influence on the Downstream Unsteady Flow Field: Part I — Wake Decay Characteristics in the Flow Passage

1990 ◽  
Author(s):  
C. Poensgen ◽  
H. E. Gallus
Keyword(s):  
Flow Field ◽  
Turbulent Flows ◽  
Velocity Vector ◽  
Three Dimensional ◽  
Time Dependent ◽  
Major Influence ◽  
Hot Wire ◽  
Compressor Cascade ◽  
Flow Passage ◽  
Turbulent Flow Field

A measuring technique based on multisensor hot-wire anemometry has been developed to determine the unsteady three-dimensional velocity vector and the structure of turbulent flows. It then has been applied to the passage and the exit flow of an annular compressor cascade, which is periodically disturbed by the wakes of a cylinder rotor, located about 50 percent of blade chord upstream. In part I of this paper the decay of the rotor wakes will be described first without stator and secondly through a stator passage. The time-dependent turbulent flow field downstream of this stator is discussed in Part II. The rotor wakes have a major influence on the development of three-dimensional separated regions inside the compressor cascade, and this interaction will be addressed in both parts of this paper.

Experimental Investigation of the Effect of the Probe Support Tail Structure on the Compressor Cascade Flow Field

2019 ◽  
Vol 36 (1) ◽  
pp. 9-18
Author(s):  
Honghui Xiang ◽  
Ning Ge ◽  
Jie Gao ◽  
Rongfei Yang ◽  
Minjie Hou
Keyword(s):  
Experimental Investigation ◽  
Flow Field ◽  
Flow Condition ◽  
Test Facility ◽  
Axial Distance ◽  
Compressor Cascade ◽  
Inlet Flow ◽  
Disturbance Intensity ◽  
Cascade Flow ◽  
Tail Structure

Abstract Aiming at resolving the problem of measuring probe blockage effect in the performance experiments of high loaded axial flow compressors, an experimental investigation of the probe support disturbance effect on the compressor cascade flow field was conducted on a transonic plane cascade test facility. The influence characteristics of the probe support tail structure on the cascade downstream flow field under different operation conditions were revealed through the detailed analysis of the test data. The results show that the aerodynamic coupling effect between the upstream probe support wake and the downstream cascade flow field is very intense. Some factors, i. e. inlet Mach number, probe support tail structure, circumferential installing position of probe, and axial distance from the probe support trailing edge to the downstream cascade, are found to have the most impact on the probe disturbance intensity. Under high speed inlet flow condition, changing probe support tail structure can’t inhibit probe support disturbance intensity effectively. Whereas under low speed inlet flow condition, compared with the cylindrical probe, the elliptic probe can inhibit probe support wake loss and reduce disturbance effects on the downstream cascade flow field.

scholarly journals Numerical and Experimental Study of Flow Field between the Main Hull and Demi-Hull of a Trimaran

2020 ◽  
Vol 8 (12) ◽  
pp. 975
Author(s):  
Cong Sun ◽  
Chunyu Guo ◽  
Chao Wang ◽  
Lianzhou Wang ◽  
Jianfeng Lin
Keyword(s):  
Flow Field ◽  
High Speed ◽  
Light Transmission ◽  
Transmission Rate ◽  
Laser Sheet ◽  
Three Dimensional ◽  
Wake Flow ◽  
Navier Stokes ◽  
Unsteady Wake ◽  
Real Flow

The interactions between the main hull and demi-hull of trimarans have been arousing increasing attention, and detailed circumferential flow fields greatly influence trimaran research. In this research, the unsteady wake flow field of a trimaran was obtained by Reynolds-Averaged Navier-Stokes (RANS) equations on the basis of the viscous flow principles with consideration of the heaving and pitching of the trimaran. Then, we designed an experimental method based on particle-image velocimetry (PIV) and obtained a detailed flow field between the main hull and demi-hull of the trimaran. A trimaran model with one demi-hull made of polycarbonate material with 90% light transmission rate and a refractive index 1.58 (close to that of water 1.33) was manufactured as the experiment sample. Using polycarbonate material, the laser-sheet light-source transmission and high-speed camera recording problems were effectively rectified. Moreover, a nonstandard calibration was added into the PIV flow field measurement system. Then, we established an inverse three-dimensional (3D) distortion coordinate system and obtained the corresponding coordinates by using optics calculations. Further, the PIV system spatial mapping was corrected, and the real flow field was obtained. The simulation results were highly consistent with the experimental data, which showed the methods established in this study provided a strong reference for obtaining the detailed flow field information between the main hull and demi-hull of trimarans.

Parametric Design of a Waterjet Pump by Means of Inverse Design, CFD Calculations and Experimental Analyses

2010 ◽  
Vol 132 (3) ◽  
Author(s):  
Duccio Bonaiuti ◽  
Mehrdad Zangeneh ◽  
Reima Aartojarvi ◽  
Jonas Eriksson
Keyword(s):  
Flow Field ◽  
Parametric Study ◽  
Parametric Design ◽  
Inverse Design ◽  
Design Parameters ◽  
Pump Design ◽  
Hydrodynamic Efficiency ◽  
Numerical Predictions ◽  
High Level ◽  
Suction Performance

The present paper describes the parametric design of a mixed-flow water-jet pump. The pump impeller and diffuser geometries were parameterized by means of an inverse design method, while CFD analyses were performed to assess the hydrodynamic and suction performance of the different design configurations that were investigated. An initial pump design was first generated and used as baseline for the parametric study. The effect of several design parameters was then analyzed in order to determine their effect on the pump performance. The use of a blade parameterization, based on inverse design, led to a major advantage in this study, because the three-dimensional blade shape is described by means of hydrodynamic parameters, such as blade loading, which has a direct impact on the hydrodynamic flow field. On the basis of this study, an optimal configuration was designed with the aim of maximizing the pump suction performance, while at the same time, guaranteeing a high level of hydrodynamic efficiency, together with the required mechanical and vibrational constraints. The final design was experimentally tested, and the good agreement between numerical predictions and experimental results validated the design process. This paper highlights the contrasting requirements in the pump design in order to achieve high hydrodynamic efficiency or good cavitation performance. The parametric study allowed us to determine design guidelines in order to find the optimal compromise in the pump design, in cases where both a high level of efficiency and suction performance must simultaneously be achieved. The design know-how developed in this study is based on flow field analyses and on hydrodynamic design parameters. It has therefore a general validity and can be used for similar design applications.

Sign in / Sign up

Export Citation Format

Share Document