scholarly journals Punching with a slant angle - cutting surface quality

2021 ◽  
Author(s):  
Adrian Schenek ◽  
Mathias Liewald
Keyword(s):  
Sheet Metal ◽  
Regression Models ◽  
Empirical Test ◽  
Three Dimensional ◽  
Slant Angle ◽  
Current State ◽  
Cutting Surface ◽  
Structural Sheet ◽  
Experimental Cutting ◽  
The Difference

For economic or process-related reasons, punching of structural sheet metal components often has to be used for car bodies. The difference in angle of attack between punch and sheet metal component is referred to as “slant angle”. However, at the current state of the art, no precise information is available on the characteristics of cutting surfaces in relation to the slant angles. For this reason, cost-intensive slider units are used for comparatively small slant angles of around 10° in order to ensure series suitability of corresponding punching processes. In this respect, recent studies performed by the authors have shown that good cutting surface qualities can also be achieved for slant angles distinctly beyond 10°. This contribution presents an empirical test series for the characterization of cutting surface parameters when punching with a slant angle. Here, the experimental cutting surface analysis showed an asymmetric characteristic of the cutting surface along the hole circumference. Furthermore, the investigated sheet metal materials HC340LA, DP600 and DP800 revealed recurring tendencies regarding the parameters “edge draw-in”, “clean cut”, “fracture surface” and “burr height”, which had been combined to corresponding three-dimensional regression models. With these regression models, cutting simulations could be calibrated, allowing a quality prognosis of cutting surfaces achievable when punching at specific slant angles.

Defocus ramp correction in spot-scan imaging

1992 ◽  
Vol 50 (1) ◽  
pp. 130-131
Author(s):  
Kenneth H. Downing
Keyword(s):  
Computer Control ◽  
Three Dimensional ◽  
Sufficient Accuracy ◽  
Objective Lens ◽  
Electron Crystallography ◽  
Contrast Transfer Function ◽  
Tilt Axis ◽  
Specimen Height ◽  
The Difference ◽  
Envelope Functions

Three-dimensional structures of a number of samples have been determined by electron crystallography. The procedures used in this work include recording images of fairly large areas of a specimen at high tilt angles. There is then a large defocus ramp across the image, and parts of the image are far out of focus. In the regions where the defocus is large, the contrast transfer function (CTF) varies rapidly across the image, especially at high resolution. Not only is the CTF then difficult to determine with sufficient accuracy to correct properly, but the image contrast is reduced by envelope functions which tend toward a low value at high defocus.We have combined computer control of the electron microscope with spot-scan imaging in order to eliminate most of the defocus ramp and its effects in the images of tilted specimens. In recording the spot-scan image, the beam is scanned along rows that are parallel to the tilt axis, so that along each row of spots the focus is constant. Between scan rows, the objective lens current is changed to correct for the difference in specimen height from one scan to the next.

J. M. Keynes as the Last Economist of Mainstream and a Precursor of Theoretical and Methodological Pluralism

2008 ◽  
pp. 120-130 ◽  
Author(s):  
N. Shapiro
Keyword(s):  
Economic Science ◽  
Methodological Pluralism ◽  
Current State ◽  
Science In Russia ◽  
The Difference

The article shows the methodological ambiguity of Keynes’ ideas. The simplified treatment of his views on the part of his followers is criticized. The author shows the difference between Keynes’ methodological disputes with classics and his debate with mathematical economists and econometricians, in particular with J. Tinbergen. It is shown that methodological discussions of 1930-1940 are actual for the assessment of the current state of economic science in Russia.

Casimir forces and vacuum energy

2017 ◽  
Author(s):  
Serge Reynaud ◽  
Astrid Lambrecht
Keyword(s):  
Casimir Force ◽  
Dimensional Space ◽  
Three Dimensional ◽  
Thermal Fluctuations ◽  
Model Systems ◽  
Vacuum Field ◽  
Force Measurements ◽  
Casimir Forces ◽  
Current State ◽  
Field Fluctuations

The Casimir force is an effect of quantum vacuum field fluctuations, with applications in many domains of physics. The ideal expression obtained by Casimir, valid for perfect plane mirrors at zero temperature, has to be modified to take into account the effects of the optical properties of mirrors, thermal fluctuations, and geometry. After a general introduction to the Casimir force and a description of the current state of the art for Casimir force measurements and their comparison with theory, this chapter presents pedagogical treatments of the main features of the theory of Casimir forces for one-dimensional model systems and for mirrors in three-dimensional space.

The iron content of iron superoxide dismutase: determination by anomalous scattering

1983 ◽  
Vol 218 (1210) ◽  
pp. 119-126 ◽  
Keyword(s):  
Superoxide Dismutase ◽  
Iron Content ◽  
Three Dimensional ◽  
Anomalous Scattering ◽  
Total Iron Content ◽  
Iron Site ◽  
Iron Superoxide Dismutase ◽  
Density Map ◽  
The Difference ◽  
Electron Density Map

The number of iron atoms in the dimeric iron-containing superoxide dismutase from Pseudomonas ovalis and their atomic positions have been determined directly from anomalous scattering measurements on crystals of the native enzyme. To resolve the long-standing question of the total amount of iron per molecule for this class of dismutase, the occupancy of each site was refined against the measured Bijvoet differences. The enzyme is a symmetrical dimer with one iron site in each subunit. The iron position is 9 ņ from the intersubunit interface. The total iron content of the dimer is 1.2±0.2 moles per mole of protein. This is divided between the subunits in the ratio 0.65:0.55; the difference between them is probably not significant. Since each subunit contains, on average, slightly more than half an iron atom we conclude that the normal state of this enzyme is two iron atoms per dimer but that some of the metal is lost during purification of the protein. Although the crystals are obviously a mixture of holo- and apo-enzymes, the 2.9 Å electron density map is uniformly clean, even at the iron site. We conclude that the three-dimensional structures of the iron-bound enzyme and the apoenzyme are identical.

scholarly journals Flowering plant embryos: How did we end up here?

2021 ◽  
Author(s):  
Stefan A. Rensing ◽  
Dolf Weijers
Keyword(s):  
Current Knowledge ◽  
General Structure ◽  
Three Dimensional ◽  
Flowering Plants ◽  
Flowering Plant ◽  
Adult Plant ◽  
Ancestral State ◽  
Evolutionary Trajectory ◽  
Current State ◽  
Plant Embryo

AbstractThe seeds of flowering plants are sexually produced propagules that ensure dispersal and resilience of the next generation. Seeds harbor embryos, three dimensional structures that are often miniatures of the adult plant in terms of general structure and primordial organs. In addition, embryos contain the meristems that give rise to post-embryonically generated structures. However common, flowering plant embryos are an evolutionary derived state. Flowering plants are part of a much larger group of embryo-bearing plants, aptly termed Embryophyta. A key question is what evolutionary trajectory led to the emergence of flowering plant embryos. In this opinion, we deconstruct the flowering plant embryo and describe the current state of knowledge of embryos in other plant lineages. While we are far yet from understanding the ancestral state of plant embryogenesis, we argue what current knowledge may suggest and how the knowledge gaps may be closed.

A New Stretch-Forming Process Based on Loading at Discrete Points and its Numerical Investigation

2013 ◽  
Vol 423-426 ◽  
pp. 737-740
Author(s):  
Zhong Yi Cai ◽  
Mi Wang ◽  
Chao Jie Che
Keyword(s):  
Sheet Metal ◽  
Three Dimensional ◽  
Discrete Point ◽  
Stretch Forming ◽  
Sheet Metal Part ◽  
Metal Part ◽  
Forming Process ◽  
Loading Trajectory ◽  
New Process ◽  
Forming Defects

A new stretch-forming process based on discretely loading for three-dimensional sheet metal part is proposed and numerically investigated. The gripping jaw in traditional stretch-forming process is replaced by the discrete array of loading units, and the stretching load is applied at discrete points on the two ends of sheet metal. By controlling the loading trajectory at the each discrete point, an optimal stretch-forming process can be realized. The numerical results on the new stretch-forming process of a saddle-shaped sheet metal part show that the distribution of the deformation on the formed surface of new process is more uniform than that of traditional stretch-forming, and the forming defects can be avoided and better forming quality will be obtained.

scholarly journals SPECTRAL CORRELATIONS IN DISORDERED MESOSCOPIC METALS AND THEIR RELEVANCE FOR PERSISTENT CURRENTS

1996 ◽  
Vol 10 (28) ◽  
pp. 1397-1406 ◽  
Author(s):  
AXEL VÖLKER ◽  
PETER KOPIETZ
Keyword(s):  
Energy Levels ◽  
Three Dimensional ◽  
Average Density ◽  
Electron Interaction ◽  
Energy Window ◽  
Persistent Currents ◽  
Dependent Part ◽  
The Difference ◽  
Aharonov Bohm ◽  
Grand Canonical

We use the Lanczos method to calculate the variance σ2(E, ϕ) of the number of energy levels in an energy window of width E below the Fermi energy for noninteracting disordered electrons on a thin three-dimensional ring threaded by an Aharonov–Bohm flux ϕ. We confirm numerically that for small E the flux-dependent part of σ2(E, ϕ) is well described by the Altshuler–Shklovskii-diagram involving two Cooperons. However, in the absence of electron–electron interactions this result cannot be extrapolated to energies E where the energy-dependence of the average density of states becomes significant. We discuss consequences for persistent currents and argue that for the calculation of the difference between the canonical- and grand canonical current it is crucial to take the electron–electron interaction into account.

Theory of ultrasonic attenuation in one and two dimensional metals

1976 ◽  
Vol 54 (14) ◽  
pp. 1454-1460 ◽  
Author(s):  
T. Tiedje ◽  
R. R. Haering
Keyword(s):  
Ultrasonic Attenuation ◽  
Three Dimensional ◽  
Electronic Systems ◽  
Two Dimensional ◽  
Temperature Dependent ◽  
One Dimensional ◽  
The Difference

The theory of ultrasonic attenuation in metals is extended so that it applies to quasi one and two dimensional electronic systems. It is shown that the attenuation in such systems differs significantly from the well-known results for three dimensional systems. The difference is particularly marked for one dimensional systems, for which the attenuation is shown to be strongly temperature dependent.

Research on Transition Zones of Spherical Surface Parts in 3D Rolling Process

2014 ◽  
Vol 687-691 ◽  
pp. 3-6
Author(s):  
Da Ming Wang ◽  
Ming Zhe Li ◽  
Zhong Yi Cai
Keyword(s):  
Sheet Metal ◽  
Spherical Surface ◽  
Three Dimensional ◽  
Rolling Process ◽  
Experimental Results ◽  
Transition Zones ◽  
Spherical Surfaces ◽  
Sheet Width ◽  
Forming Precision ◽  
Roll Gap

3D rolling is a novel technology for three-dimensional surface parts. In this process, by controlling the gap between the upper and lower forming rolls, the sheet metal is non-uniformly thinned in thickness direction, and the longitudinal elongation of the sheet metal is different along the transverse direction, which makes the sheet metal generate three-dimensional deformation. In this paper, the transition zones of spherical surface parts in 3D rolling process are investigated. Spherical surface parts with the same widths but different lengths are simulated in condition of the same roll gap, and their experimental results are presented. The forming precision of forming parts and the causes of transition zones in the head and tail regions are analyzed through simulated results. The simulated and experimental results show that the lengths of transition zones of spherical surfaces in the head and tail regions are fixed values in condition of the same sheet width and roll gap.

Sign in / Sign up

Export Citation Format

Share Document