scholarly journals Device for plastic compression of long-dimensional cylindrical samples in linear stress conditions

2018 ◽  
Vol 84 (8) ◽  
pp. 61-64
Author(s):  
A. D. Khvan ◽  
D. V. Khvan ◽  
A. A. Voropaev ◽  
Yu. B. Rukin
Keyword(s):  
Experimental Data ◽  
Sliding Friction ◽  
Test Sample ◽  
Cylindrical Sample ◽  
Transcendental Equation ◽  
Taper Angle ◽  
Plastic Compression ◽  
Mobile Links ◽  
Accurate Experimental Data

A design of the device for studying plastic compression of long cylindrical specimens under conditions of a linear stress state is presented. The device is developed to study the properties of metals under plastic deformation in conditions of nonmonotonic loading. The goal of getting the accurate experimental data entails the necessary of carrying out tests using one long-length cylindrical sample, with the calculated length being more than five diameters. To prevent flexure of the long-length sample upon compression, the support conical sectors made by cutting truncated cone shaped blank into 6 or 8 equal parts with a central longitudinal hole having a diameter equal to the diameter of the test sample are used. The sectors are coupled by two pairs of semirings. A transcendental equation is obtained for determination of the taper angle of those sectors on the basis of kinematic analysis of the mobile links. This angle depends on the total weight of the sectors and sliding friction coefficients in the corresponding kinematic pairs of the device. For the considered device, the taper angle of the sectors is 36°. This device is designed and manufactured for compression testing of the samples with a diameter of 16.5 mm and a gaged length of 135 mm. Samples from steel 45 are tested with a goal of the flow curve construction and experimental verification of the strain diagrams under conditions of cyclic tensile-compression. Comparison of the calculated and experimental data proved the satisfactory accuracy of the stress determination, which makes it possible to recommend this device as a testing tool to be used in mechanical laboratories of the universities and research institutes.

Tribotechnical characteristics of hard alloys in sliding friction units

2020 ◽  
pp. 87-97
Author(s):  
K. D. Khromushkin ◽  
B. G. Ushakov ◽  
A. V. Kochergin ◽  
R. A. Suleev ◽  
O. N. Parmenova
Keyword(s):  
Experimental Data ◽  
Sliding Friction ◽  
Heating Temperature ◽  
Hard Alloys ◽  
Friction Units ◽  
Wear And Friction ◽  
Friction Path ◽  
Friction Parameters ◽  
Tribotechnical Characteristics ◽  
Temperature Surface

The paper presents experimental data on the study of the friction parameters of hard alloys in sliding friction units, including the heating temperature, surface roughness, wear and friction coefficient, depending on the duration of the test and the friction path.

Equilibrium Sorptions in Heterogeneous Ion Exchange Membranes

1992 ◽  
Vol 57 (9) ◽  
pp. 1905-1914
Author(s):  
Miroslav Bleha ◽  
Věra Šumberová
Keyword(s):  
Experimental Data ◽  
Ion Exchange ◽  
Total Content ◽  
Distribution Coefficients ◽  
Exchange Capacity ◽  
Ion Exchange Membranes ◽  
Ion Exchange Capacity ◽  
Equilibrium Sorption ◽  
Inhomogeneity Factor

The equilibrium sorption of uni-univalent electrolytes (NaCl, KCl) in heterogeneous cation exchange membranes with various contents of the ion exchange component and in ion exchange membranes Ralex was investigated. Using experimental data which express the concentration dependence of equilibrium sorption, validity of the Donnan relation for the systems under investigation was tested and values of the Glueckauf inhomogeneity factor for Ralex membranes were determined. Determination of the equilibrium sorption allows the effect of the total content of internal water and of the ion-exchange capacity on the distribution coefficients of the electrolyte to be determined.

Numerical evaluation of hydrodynamic characteristics of planing hulls by using a hybrid method

2021 ◽  
pp. 147509022199024
Author(s):  
Emre Kahramanoglu ◽  
Silvia Pennino ◽  
Huseyin Yilmaz
Keyword(s):  
Experimental Data ◽  
Hybrid Method ◽  
Design Stage ◽  
Hydrodynamic Characteristics ◽  
Calm Water ◽  
Preliminary Design Stage ◽  
Reduction Function ◽  
Hull Forms ◽  
Good Agreement

The hydrodynamic characteristics of the planing hulls in particular at the planing regime are completely different from the conventional hull forms and the determination of these characteristics is more complicated. In the present study, calm water hydrodynamic characteristics of planing hulls are investigated using a hybrid method. The hybrid method combines the dynamic trim and sinkage from the Zarnick approach with the Savitsky method in order to calculate the total resistance of the planing hull. Since the obtained dynamic trim and sinkage values by using the original Zarnick approach are not in good agreement with experimental data, an improvement is applied to the hybrid method using a reduction function proposed by Garme. The numerical results obtained by the hybrid and improved hybrid method are compared with each other and available experimental data. The results indicate that the improved hybrid method gives better results compared to the hybrid method, especially for the dynamic trim and resistance. Although the results have some discrepancies with experimental data in terms of resistance, trim and sinkage, the improved hybrid method becomes appealing particularly for the preliminary design stage of the planing hulls.

A Technique for the Laboratory Determination of Recirculation in Single Needle Dialysis

1993 ◽  
Vol 16 (2) ◽  
pp. 63-70 ◽  
Author(s):  
N.A. Hoenich ◽  
P.T. Smirthwaite ◽  
C. Woffindin ◽  
P. Lancaster ◽  
T.H. Frost ◽  
...  
Keyword(s):  
Experimental Data ◽  
Flow Rate ◽  
Experimental Results ◽  
New Technique ◽  
Treatment Efficiency ◽  
Single Lumen ◽  
Theoretical Predictions ◽  
Lumen Catheter ◽  
A New Technique

Recirculation is an important factor in single needle dialysis and, if high, can compromise treatment efficiency. To provide information regarding recirculation characteristics of access devices used in single needle dialysis, we have developed a new technique to characterise recirculation and have used this to measure the recirculation of a Terumo 15G fistula needle and a VasCath SC2300 single lumen catheter. The experimentally obtained results agreed well with those established clinically (8.5 ± 2.4% and 18.4 ± 3.4%). The experimental results have also demonstrated a dependence on access type, pump speeds and fistula flow rate. A comparison of experimental data with theoretical predictions showed that the latter exceeded those measured with the largest contribution being due to the experimental fistula.

Theoretical determination of the structures of CaSiO3 perovskites

2006 ◽  
Vol 62 (6) ◽  
pp. 1025-1030 ◽  
Author(s):  
Razvan Caracas ◽  
Renata M. Wentzcovitch
Keyword(s):  
Crystal Structure ◽  
Experimental Data ◽  
Density Functional Theory ◽  
Density Functional ◽  
Theoretical Determination ◽  
Functional Theory ◽  
Starting Point ◽  
Atomic Coordinates ◽  
The Ideal

Density functional theory is used to determine the possible crystal structure of the CaSiO3 perovskites and their evolution under pressure. The ideal cubic perovskite is considered as a starting point for studying several possible lower-symmetry distorted structures. The theoretical lattice parameters and the atomic coordinates for all the structures are determined, and the results are discussed with respect to experimental data.

A Critical Review on the Determination of Pressure Drop During Condensation in Smooth and Enhanced Tubes

2013 ◽  
Author(s):  
Ahmet Selim Dalkiliç ◽  
Ali Celen ◽  
Mohamed M. Awad ◽  
Somchai Wongwises
Keyword(s):  
Neural Network ◽  
Heat Transfer ◽  
Experimental Data ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Critical Review ◽  
Heat Exchangers ◽  
Numerical Analyses ◽  
Enhanced Tubes

Heat exchangers using in-tube condensation have great significance in the refrigeration, automotive and process industries. Effective heat exchangers have been rapidly developed due to the demand for more compact systems, higher energy efficiency, lower material costs and other economic incentives. Enhanced surfaces, displaced enhancement devices, swirl-flow devices and surface tension devices improve the heat transfer coefficients in these heat exchangers. This study is a critical review on the determination of the condensation heat transfer coefficient of pure refrigerants flowing in vertical and horizontal tubes. The authors’ previous publications on this issue, including the experimental, theoretical and numerical analyses are summarized here. The lengths of the vertical and horizontal test sections varied between 0.5 m and 4 m countercurrent flow double-tube heat exchangers with refrigerant flowing in the inner tube and cooling water flowing in the annulus. The measured data are compared to theoretical and numerical predictions based on the solution of the artificial intelligence methods and CFD analyses for the condensation process in the smooth and enhanced tubes. The theoretical solutions are related to the design of double tube heat exchangers in refrigeration, air conditioning and heat pump applications. Detailed information on the in-tube condensation studies of heat transfer coefficient in the literature is given. A genetic algorithm (GA), various artificial neural network models (ANN) such as multilayer perceptron (MLP), radial basis networks (RBFN), generalized regression neural network (GRNN), and adaptive neuro-fuzzy inference system (ANFIS), and various optimization techniques such as unconstrained nonlinear minimization algorithm-Nelder-Mead method (NM), non-linear least squares error method (NLS), and Ansys CFD program are used in the numerical solutions. It is shown that the convective heat transfer coefficient of laminar and turbulent condensing film flows can be predicted by means of theoretical and numerical analyses reasonably well if there is a sufficient amount of reliable experimental data. Regression analysis gave convincing correlations, and the most suitable coefficients of the proposed correlations are depicted as compatible with the large number of experimental data by means of the computational numerical methods.

Parameter Study of Offset Press Cylinder Based on Sliding Friction

2010 ◽  
Vol 174 ◽  
pp. 299-302 ◽  
Author(s):  
Hai Yan Zhang ◽  
He Ping Hou ◽  
Jun Feng Si ◽  
Xiao Yu Chen
Keyword(s):  
Contact Area ◽  
Sliding Friction ◽  
Accurate Determination ◽  
Rolling Process ◽  
Elastic Cylinder ◽  
Parameter Study ◽  
Cylinder Radius ◽  
Printing Quality ◽  
Dot Gain

In the contact area of offset, a relative slide occurs between the surface of plate cylinder and blanket cylinder, which changes the print image and influences the printing quality. The relative slide in the cylinders’ rolling process is investigated, and the determination rule of cylinders’ geometric parameters of offset press is proposed. The results show that the relative slide is minimization under the condition that the compression of elastic cylinder radius is 0.2 times bigger than that of rigid cylinder radius, and the deformation of print image and dot gain both are minimization. The results provide theoretical direction for accurate determination of cylinder radius of offset press.

Sign in / Sign up

Export Citation Format

Share Document