scholarly journals Investigations on force generation and joint properties of dissimilar thickness friction stir corner welded AA 5086 alloy

2020 ◽  
Vol 40 (1) ◽  
pp. 67-74
Author(s):  
Manigandan Krishnan ◽  
Senthilkumar Subramaniam
Keyword(s):  
Tensile Strength ◽  
Friction Stir Welding ◽  
Welding Speed ◽  
Welding Process ◽  
Spindle Motor ◽  
Parent Material ◽  
Force Generation ◽  
Friction Stir ◽  
Current Consumption ◽  
Spindle Motor Current

The force generation, joint mechanical and metallurgical properties of friction stir corner welded non-heat treatable AA 5086 aluminum alloy are investigated in this paper. The friction stir welding process is carried out with the plate thicknesses of 6 mm and 4 mm. The welding speed, tool rotational speed and tool plunge depth were considered as the process parameters to conduct the welding experiments. The machine spindle motor current consumption and tool down force generation during friction stir welding were analyzed. The microstructures of various joint regions were observed. The tensile samples revealed the tensile strength of 197 MPa with tool rotational and welding speeds of 1,000 rev/min and 150 mm/min respectively, which is 78 % of parent material tensile strength. A maximum micro hardness of 98 HV was observed at thermomechanically joint affected zone, which was welded with tool rotation of 1,000 rev/min and welding speed of 190 mm/min.

Enhancements on dissimilar friction stir welding between AZ31 and SPHC mild steel with Al-Mg as powder additives

2021 ◽  
pp. 1-22
Author(s):  
Mohd Ridha Muhamad ◽  
Sufian Raja ◽  
Mohd Fadzil Jamaludin ◽  
Farazila Yusof ◽  
Yoshiaki Morisada ◽  
...  
Keyword(s):  
Tensile Strength ◽  
Friction Stir Welding ◽  
Mild Steel ◽  
Welding Speed ◽  
Welded Joint ◽  
Microstructural Analysis ◽  
Welding Process ◽  
Dissimilar Materials ◽  
Friction Stir ◽  
Welding Interface

Abstract Dissimilar materials joining between AZ31 magnesium alloy and SPHC mild steel with Al-Mg powder additives were successfully produced by friction stir welding process. Al-Mg powder additives were set in a gap between AZ31 and SPHC specimen's butt prior to welding. The experiments were performed for different weight percentages of Al-Mg powder additives at welding speeds of 25 mm/min, 50 mm/min and 100 mm/min with a constant tool rotational speed of 500 rpm. The effect of powder additives and welding speed on tensile strength, microhardness, characterization across welding interface and fracture morphology were investigated. Tensile test results showed significant enhancement of tensile strength of 150 MPa for 10% Al and Mg (balance) powder additives welded joint as compared to the tensile strength of 125 MPa obtained for welded joint without powder additives. The loss of aluminium in the alloy is compensated by Al-Mg powder addition during welding under a suitable heat input condition identified by varying welding speeds. Microstructural analysis revealed that the Al-Mg powder was well mixed and dispersed at the interface of the joint at a welding speed of 50 mm/min. Intermetallic compound detected in the welding interface contributed to the welding strength.

Multi-response optimization of friction stir welding process parameters for dissimilar joining of Al6101 to pure copper using standard deviation based TOPSIS method

2019 ◽  
Vol 233 (18) ◽  
pp. 6473-6482 ◽  
Author(s):  
Nidhi Sharma ◽  
Zahid A Khan ◽  
Arshad Noor Siddiquee ◽  
Mohd Atif Wahid
Keyword(s):  
Tensile Strength ◽  
Friction Stir Welding ◽  
Ultimate Tensile Strength ◽  
Process Parameters ◽  
Welding Speed ◽  
Welding Process ◽  
Micro Hardness ◽  
Friction Stir ◽  
Friction Stir Welding Process ◽  
Response Optimization

Friction stir welding is a new and effective solid-state welding process for joining dissimilar materials such as aluminum (Al) and copper (Cu). Joint quality of the friction stir welded materials gets influenced by the welding strategy and different friction stir welding process parameters, i.e. rotational speed, welding speed, tool design, tool pin offset, and tilt angle. In this paper, the effect of combination of different friction stir welding process parameters during joining of Al-6101 and pure copper is studied using Taguchi L18 orthogonal array. Four friction stir welding process parameters, i.e. shoulder diameter (A), pin offset (B), welding speed (C), and rotational speed (D) each at three levels except shoulder diameter, which is at two levels are selected. The effect of different combinations of these parameters on ultimate tensile strength and micro-hardness of the joints is investigated. Subsequently, single response optimization for ultimate tensile strength and micro-hardness and multi-response optimization of ultimate tensile strength and micro-hardness taken together is carried out to obtain the optimal combination of the friction stir welding process parameters. Taguchi method is used for single response optimization, whereas Taguchi-based TOPSIS method is employed for multi-response optimization. For single optimization, the optimum combination of the friction stir welding parameters yielding maximum strength and micro-hardness are A1B1C2D2 and A2B1C2D3, respectively. The optimum combination of the process parameters for multi-response optimization is A2B1C2D2. From the results of the study for single- and multi-response optimization, it is revealed that the rotational speed is the most significant process parameter affecting the tensile strength and micro-hardness of the joints followed by the welding speed. Further, the macro/microstructure and micro-hardness profile of the joint obtained at the optimal combination of the multi-response optimization are given and discussed for better understanding of material mixing and joining.

Effect of Friction Stir Welding Parameters on Thermal and Tensile Behavior of Aluminum Weldments Using Double Shoulder Tools

2012 ◽  
Vol 622-623 ◽  
pp. 323-329
Author(s):  
Ebtisam F. Abdel-Gwad ◽  
A. Shahenda ◽  
S. Soher
Keyword(s):  
Tensile Strength ◽  
Friction Stir Welding ◽  
Welding Process ◽  
Tensile Behavior ◽  
Frictional Heat ◽  
Welding Parameters ◽  
Friction Stir ◽  
Aluminum Base ◽  
Tool Pin ◽  
Strength And Ductility

Friction stir welding (FSW) process is a solid state welding process in which the material being welded does not melt or recast. This process uses a non-consumable tool to generate frictional heat in the abutting surfaces. The welding parameters and tool pin profile play major roles in deciding the weld quality. In this investigation, an attempt has been made to understand effects of process parameters include rotation speeds, welding speeds, and pin diameters on al.uminum weldment using double shoulder tools. Thermal and tensile behavior responses were examined. In this direction temperatures distribution across the friction stir aluminum weldment were measured, besides tensile strength and ductility were recorded and evaluated compared with both single shoulder and aluminum base metal.

Influence of Friction Stir Welding Process on the Weld Formation and Tensile Strength of Titanium and Aluminum Dissimilar Alloys Welded Joint

2011 ◽  
Vol 189-193 ◽  
pp. 3266-3269 ◽  
Author(s):  
Yu Hua Chen ◽  
Peng Wei ◽  
Quan Ni ◽  
Li Ming Ke
Keyword(s):  
Tensile Strength ◽  
Friction Stir Welding ◽  
Cross Section ◽  
Welded Joint ◽  
Welding Process ◽  
Dissimilar Materials ◽  
Influence Of Process Parameters ◽  
Friction Stir ◽  
Dissimilar Alloys ◽  
Titanium Aluminum

Titanium alloy TC1 and Aluminum alloy LF6 were jointed by friction stir welding (FSW), and the influence of process parameters on formation of weld surface, cross-section morphology and tensile strength were studied. The results show that, Titanium and Aluminum dissimilar alloy is difficult to be joined by FSW, and some defects such as cracks and grooves are easy to occur. When the rotational speed of stir head(n) is 750r/min and 950r/min, the welding speed(v) is 118mm/min or 150mm/min, a good formation of weld surface can be obtained, but the bonding of titanium/aluminum interface in the cross-section of weld joint is bad when n is 750r/min which results in a low strength joint. When n is 950r/min and v is 118mm/min，the strength of the FSW joint of Titanium/Aluminum dissimilar materials is 131MPa which is the highest．

Optimization of Welding Process Parameters in Novel Friction Stir Welding of Polyamide 66 Joints

2019 ◽  
Vol 969 ◽  
pp. 828-833 ◽  
Author(s):  
R. Nandhini ◽  
R. Dinesh Kumar ◽  
S. Muthukumaran ◽  
S. Kumaran
Keyword(s):  
Tensile Strength ◽  
Friction Stir Welding ◽  
Process Parameters ◽  
Welding Process ◽  
Polyamide 66 ◽  
Friction Stir ◽  
Response Characteristics ◽  
Tool Shoulder ◽  
Stereo Microscope ◽  
Friction Plate

The friction stir welding of polyamide 66 with a specially modified tool is studied. A variation of the conventional friction stir welding is investigated by incorporating a friction plate for the purpose of heating the polymer in the course of welding process through the tool shoulder. This in turn, improves the efficiency of the weld. The association of the welding process parameters and the weld performance has been investigated by the grey relational analysis with multi response characteristics like weld tensile strength, percent elongation and hardness. Macrostructure of the weld joint cross section has been explored by Stereo microscope. The maximum weld tensile strength of 63 MPa and a Shore hardness of 60 D at the weld nugget are obtained. The hardness profiles of the welded samples have been analyzed in this investigation.

Heat Transfer Simulations and Analysis of Joint Cross-Sectional Microstructure on Friction Stir Welding between Steel and Aluminium

2020 ◽  
Vol 863 ◽  
pp. 85-95
Author(s):  
Truong Minh Nhat ◽  
Truong Quoc Thanh ◽  
Tu Vinh Thong ◽  
Tran Trong Quyet ◽  
Luu Phuong Minh
Keyword(s):  
Tensile Strength ◽  
Aluminum Alloy ◽  
Friction Stir Welding ◽  
Thermal Contact ◽  
Welding Process ◽  
Welding Parameters ◽  
Thermal Imager ◽  
Sem Images ◽  
Cross Sectional ◽  
Friction Stir

This study presents conducted heat simulations and experimental jointing flat-plate of aluminum alloy 6061 and SUS 304. Temperature is simulated by the COMSOL software in three states: (1) Preheat the Friction Stir Welding (FSW) by TIG welding, (2) Thermal contact resistance between Aluminium and steel, and (3) The welding process using stiring friction is simulated. The simulations intended to predicting the temperature which is used for preheat and welding process to ensuring the required solid-state welding. The temperature is also determined and checked by a thermal imager comparing with simulation results. Besides, the results of tensile strength is carried out. The Box - Behnken method is used to identify the relationship between the welding parameters (rotation, speed and offset), temperature and tensile strength. The maximum tensile strength is 77% compared to the strength of aluminum alloy. The optimal set of parameters for the process is n = 676 rpm, v = 46 mm / min and x = 0.6 mm. The optimizing welding parameters to achieving good quality of welding process are described. SEM images to determine some properties of welding materials. This is also the basis for initial research to identify some defects in welding of two different materials (IMC thickness and interconnected pores) and the cause of these defects.

Sign in / Sign up

Export Citation Format

Share Document