Melting ranges of heterophase systems Zr – Si – ZrB2 – ZrSi2-MoSi2 and Zr – Si – HfB2 – HfSi2 – MoSi2

2020 ◽  
Vol 12 ◽  
pp. 5-15
Author(s):  
M. V. Zinovyeva ◽  
◽  
V. V. Sanin ◽  
Yu. S. Pogozhev ◽  
Ye. A. Levashov ◽  
...  

The work is devoted to studying the melting ranges of the base Zr – Si eutectic composition depending on the content of the heterophasic powder component in the ZrB2 – ZrSi2 – MoSi2 and HfB2 – HfSi2 – MoSi2 systems in an amount of 30 – 90 % obtained by the method of self-propagating high-temperature synthesis (SHS). The melting range of the mixture Zr – Si was 1420 – 1440 °C, while the addition of SHS-powders ZrB2 – ZrSi2 – MoSi2 led to an increase in the melting onset temperature Тmelt.onset to 1460 – 1560 °С and the complete melting temperature Tmelt.complete to 1480 – 1670 °C. The addition of HfB2 – HfSi2 – MoSi2 powders had a weak effect on the values of Тmelt.onset (1390 – 1430 °С), but led to an increase in the values of Tmelt.complete to 1510 – 1550 °С. X-ray phase analysis showed that the remelted samples contained ZrB2/HfB2, ZrSi2/HfSi2, MoSi2 phases and Si, with the number of phases being directly proportional to the content of SHS powders in the composition of the Zr – Si mixture. The ingots were characterized by a homogeneous structure consisting of a silicon matrix, ZrSi2/HfSi2, MoSi2 disilicide grains, with ZrB2/HfB2 diboride inclusions.

2020 ◽  
Vol 15 (4) ◽  
pp. 27-32
Author(s):  
Irina V. Milyukova ◽  
Marina P. Boronenko

The work is devoted to the technology for the reduction of molybdenum from oxides by the method of self-propagating high-temperature synthesis in the MoO3 AI system with the addition of aluminum. The experiment was carried out in two modes: in a reactor at different pressures without preliminary heating and in a furnace in air until the initiation of the SH-synthesis process. Samples of molybdenum metal were obtained in different synthesis modes. X-ray phase and X-ray spectral analysis showed that molybdenum is the main phase in the synthesized samples. The presence of slag oxide phases Al2O3 and MoO2 was detected.


2016 ◽  
Vol 675-676 ◽  
pp. 623-626 ◽  
Author(s):  
Tawat Chanadee ◽  
Sutham Niyomwas

Silicon-silicon carbide (Si-SiC) composite powders were synthesized by in-situ self- propagating high-temperature synthesis using rice husk ash (RHA)/carbon/Mg as precursors in argon atmosphere. The as-SHS powders were leached by two leaching steps. The microstructure and chemical composition of the obtained Si-SiC composite powders were examined using scanning electron microscope (SEM) and x-ray diffractometer (XRD), respectively.


2012 ◽  
Vol 626 ◽  
pp. 138-142
Author(s):  
Saowanee Singsarothai ◽  
Vishnu Rachpech ◽  
Sutham Niyomwas

The steel substrate was coated by Fe-based composite using self-propagating high-temperature synthesis (SHS) reaction of reactant coating paste. The green paste was prepared by mixing precursor powders of Al, Fe2O3and Al2O3. It was coated on the steel substrate before igniting by oxy-acetylene flame. The effect of coating paste thickness and the additives on the resulted Fe-based composite coating was studied. The composite coating was characterized by X-ray diffraction (XRD) and scanning electron microscope (SEM) couple with dispersive X-ray (EDS).


2016 ◽  
Vol 685 ◽  
pp. 719-723 ◽  
Author(s):  
Maxim G. Krinitcyn ◽  
Gennadii A. Pribytkov ◽  
Vasiliy G. Durakov

A structure of Ti-TiC coatings with different content of titanium binder, overlaid of composite powders, which were obtained by self-propagating high-temperature synthesis, was investigated. The structure was studied by X-ray analysis and metallography. A size of the carbide particles in coatings, hardness of coatings and rate of wear were measured.


1990 ◽  
Vol 68 (8) ◽  
pp. 1444-1449 ◽  
Author(s):  
Martin K. Ehlert ◽  
Steven J. Rettig ◽  
Alan Storr ◽  
Robert C. Thompson ◽  
James Trotter

A moderately high-yield, high temperature synthesis of the title compound is reported. Crystals of tris[(3,5-dimethylpyrazolato-N1,N2)copper(I)] are triclinic, a = 12.360(4), b = 14.637(4), c = 12.358(4) Å, α = 105.29(2), β = 119.83(2), γ = 93.99(3)°, Z = 4 (trimers, two per asymmetric unit), space group [Formula: see text]. The structure was solved by heavy atom methods and was refined by full-matrix least-squares procedures to R = 0.034 and Rw = 0.038 for 3877 reflections with I ≥ 3σ(I). The structure consists of trimeric molecules with an unusually short average Cu—N distance of 1.852 Å. The central Cu3N6 nine-membered rings are planar to within 0.07 Å. The trimer units are linked in pairs about centres of symmetry by weak [Formula: see text] interactions averaging 2.946 Å. Keywords: pyrazolato copper (I) timer, copper (I) pyrazolate.


2013 ◽  
Vol 748 ◽  
pp. 46-50 ◽  
Author(s):  
Saowanee Singsarothai ◽  
Sutham Niyomwas

Fe-W based composite have successfully been prepared using natural resource. The ferberite (Fe (Mn, Sn)WO4) tailings mixed with aluminum, carbon and boron oxide powder were used as reactants. The reactants were pressed and followed by oxy-acetylene flame ignition. The products from the self-propagating high-temperature synthesis (SHS) reaction were characterized by X-ray diffraction (XRD) and scanning electron microscope (SEM) couple with dispersive X-ray (EDS).


2010 ◽  
Vol 658 ◽  
pp. 408-411
Author(s):  
Hui Xie ◽  
Lei Jia ◽  
Si Ming Wang ◽  
Ji Ling Zhu ◽  
Zhen Lin Lu

Cu-Mo-Si alloys with different Cu contents were prepared by self-propagation high-temperature synthesis (SHS). The microstructure and the worn surface morphology were observed using scanning electron microscopy (SEM) together with energy dispersive X-ray spectroscopy (EDS) analysis. Phase composition was determined by X-ray diffraction (XRD). The wear behavior of the Cu-Mo-Si alloys was characterized by pin-on-disc wear tester. The results showed that most of Si atoms dissolved in Cu matrix or resulted in formation of compound with Cu, while only small amount of Si atoms reacted with Mo atoms to form Mo5Si3 particles in the Cu-Ni-Si alloys with 80% Cu content. The wear rate of Cu-Mo-Si alloys descended with a decrease of Cu content, and the predominant wear mechanism could be identified as abrasive wear for Cu content less than 90% and plastic deformation for Cu content higher than 90%.


Sign in / Sign up

Export Citation Format

Share Document