scholarly journals Analisis Penambahan Reflektor Sudut pada Antena V-Double Dipole pada Frekuensi Kerja 1.800 MHz

2020 ◽  
Vol 17 (2) ◽  
pp. 37
Author(s):  
Ikhwan Ikhawan ◽  
Raisah Hayati ◽  
Misriana Misriana ◽  
Nasri Nasri
Keyword(s):  
Return Loss

Antena adalah komponen yang dirancang untuk mengirim dan menerima gelombang elektromagnetik. Penambahan reflektor sudut pada antena untuk membatasi radiasi agar tidak melebar ke belakang, namun pancarannya akan diperkuat ke arah sebaliknya dan dapat meningkatkan gain pada suatu antena. Parameter-parameter antena dapat mempengaruhi kualitas suatu antena. Dalam penelitian ini, parameter antena yang diukur berupa VSWR, return loss, pola radiasi, dan gain. Hasil pengukuran antena V-Double Dipole pada frekuensi 1.800 MHz memiliki VSWR sebesar 1,16 dan return loss sebesar -22,4 dB. Impedansi antena 58,10 Ω dan bandwidth sebesar 70 MHz. Pada pengukuran gain, digunakan 3 antena yang bekerja pada frekuensi yang sama, dimana antena-antena tersebut berfungsi sebagai antena pembanding. Pada pengukuran gain ini dilakukan dengan mengubah-ubah sudut reflektornya, yaitu 90° dan 60°.  Berdasarkan hasil pengukuran yang dilakukan pada antena V-Double Dipole dengan penambahan reflektor sudut 90° diperoleh nilai gain sebesar 9,8 dB, dan pada sudut 60° diperoleh nilai gain sebesar 15 dB. Sedangkan sebelum penambahan reflektor diperoleh gain sebesar 5 dB. Jadi penambahan reflektor dapat meningkatkan gain, dan makin kecil sudut reflektor maka gainnya semakin tinggi.

Metamaterial Structure with Negative μ and ε for reduction of return loss of Microstrip Patch Antenna

2012 ◽  
Vol 2 (8) ◽  
pp. 130-133
Author(s):  
Amandeep Singh Amandeep Singh ◽  
◽  
Sankul Agarwal ◽  
Vaibhav Sharma ◽  
Shivam Pandita
Keyword(s):  
Patch Antenna ◽  
Return Loss ◽  
Microstrip Patch Antenna ◽  
Metamaterial Structure ◽  
Microstrip Patch

A Single Band Antenna Design for Future Millimeter Wave Wireless Communication at 38 GHz

2018 ◽  
Vol 3 (1) ◽  
pp. 35 ◽  
Author(s):  
Cihat Şeker ◽  
Turgut Ozturk ◽  
Muhammet Tahir Güneşer
Keyword(s):  
Millimeter Wave ◽  
Mobile Communications ◽  
Return Loss ◽  
Computer Software ◽  
Dielectric Substrate ◽  
Single Band ◽  
Microstrip Patch ◽  
Fifth Generation ◽  
Wireless Application ◽  
5G Mobile Communications

In this proposed paper, a single band microstrip patch antenna for fifth generation (5G) wireless application was presented. 28, 38, 60 and 73 GHz frequency bands have been allocated for 5G mobile communications by International Telecommunications Union (ITU). In this paper, we proposed an antenna, which is suitable for the millimeter wave frequency. The single band antenna consists of new slot loaded on the radiating patch with the 50 ohms microstrip line feeding used. This single band antenna was simulated on a FR4 dielectric substrate have relative permittivity 4.4, loss tangent 0.02, and height 1.6 mm. The antenna was simulated by Electromagnetic simulation, computer software technology High Frequency Structural Simulator. And simulated result on return loss, VSWR, radiation pattern and 3D gain was presented. The parameters of the results well coherent and proved the literature for millimeter wave 5G wireless application at 38 GHz.

Performance enhancement of Echo Cancellation Using a Combination of Partial Update ( PU) Methods and New Variable Length LMS (NVLLMS) Algorithm

2018 ◽  
Vol 24 (5) ◽  
pp. 66
Author(s):  
Thamer M. Jamel ◽  
Faez Fawzi Hammood
Keyword(s):  
Mean Square Error ◽  
Return Loss ◽  
Performance Enhancement ◽  
Variable Length ◽  
Echo Cancellation ◽  
Convergence Time ◽  
Length Variation ◽  
Mean Square ◽  
Step Size ◽  
Echo Return Loss Enhancement

In this paper, several combination algorithms between Partial Update LMS (PU LMS) methods and previously proposed algorithm (New Variable Length LMS (NVLLMS)) have been developed. Then, the new sets of proposed algorithms were applied to an Acoustic Echo Cancellation system (AEC) in order to decrease the filter coefficients, decrease the convergence time, and enhance its performance in terms of Mean Square Error (MSE) and Echo Return Loss Enhancement (ERLE). These proposed algorithms will use the Echo Return Loss Enhancement (ERLE) to control the operation of filter's coefficient length variation. In addition, the time-varying step size is used.The total number of coefficients required was reduced by about 18% , 10% , 6%, and 16% using Periodic, Sequential, Stochastic, and M-max PU NVLLMS algorithms respectively, compared to that used by a full update method which  is very important, especially in the application of mobile communication since the power consumption must be considered. In addition, the average ERLE and average Mean Square Error (MSE) for M-max PU NVLLMS are better than other proposed algorithms.  

Optimization of Scattering Parameters through Numerical Investigation of One-bit RF MEMS Switch over Ku, K and Ka Band

2020 ◽  
Vol 12 ◽  
Author(s):  
Pampa Debnath ◽  
Ujjwal Mondal ◽  
Arpan Deyasi
Keyword(s):  
Transmission Line ◽  
Numerical Investigation ◽  
Line Width ◽  
Insertion Loss ◽  
Return Loss ◽  
Rf Mems ◽  
Rf Mems Switch ◽  
Ka Band ◽  
Mems Switch ◽  
Overlap Area

Aim:: Computation of loss factors for one-bit RF MEMS switch over Ku, K and Ka-band for two different insulating substrates. Objective:: Numerical investigation of return loss, insertion loss, isolation loss are computed under both actuated and unactuated states for two different insulating substrates of the 1-bit RF MEMS switch, and corresponding up and down-capacitances are obtained. Methods:: The unique characteristics of a 1-bit RF MEMS switch of providing higher return loss under both actuated and unactuated states and also of isolation loss with negligible insertion loss makes it as a prime candidate for phase shifter application. This is presented in this manuscript with a keen focus on improvement capability by changing transmission line width, and also of overlap area; where dielectric constant of the substrate also plays a vital role. Results:: The present work exhibits very low down-capacitance over the spectrum whereas considerable amount of up-capacitance. Also when overall performance in terms of all loss parameters are considered, switch provides very low insertion loss, good return loss under actuated state and standard isolation loss. Conclusion:: Reduction of transmission line width of about 33% improved the performance of the switch by increasing isolation loss. Isolation loss of -40 dB is obtained at actuated condition in higher microwave spectra for SiO 2 at higher overlap area. Down capacitance of ~ 1dB is obtained which is novel as compared with other published literature. Moreover, a better combination of both return loss, isolation loss and insertion loss are reported in this present work compared with all other published data so far.

scholarly journals A balanced-to-balanced directional coupler based on branch-slotline coupled structure

Frequenz ◽  
2020 ◽  
Vol 74 (11-12) ◽  
pp. 427-433
Author(s):  
Yaxin Liu ◽  
Feng Wei ◽  
Xiaowei Shi ◽  
Cao Zeng
Keyword(s):  
Directional Coupler ◽  
Return Loss ◽  
Design Method ◽  
Differential Mode ◽  
Arbitrary Power ◽  
Measurement Results ◽  
Transition Structures ◽  
Coupled Structures ◽  
Better Than ◽  
Good Agreement

AbstractIn this paper, a balanced-to-balanced (BTB) branch-slotline directional coupler (DC) is firstly presented, which can realize an arbitrary power division ratios (PDRs). The coupler is composed by microstrip-to-slotline (MS) transition structures and branch-slotline coupled structures. The single-ended to balanced-ended conversion is simplified and easy to implemented by the MS transition structures, which intrinsically leads to the differential-mode (DM) transmission and common-mode (CM) suppression. Moreover, the different PDRs which are controlled by the widths of branch-slotlines can be achieved. In order to verify the feasibility of the proposed design method, two prototype circuits of the proposed coupler with different PDRs are fabricated and measured. The return loss and the isolation of two designs are all better than 10 dB. Moreover, the CM suppressions are greater than 35 dB. A good agreement between the simulation and measurement results is observed.

Tunable balanced to balanced filtering power divider with high common-mode suppression

Frequenz ◽  
2020 ◽  
Vol 74 (7-8) ◽  
pp. 263-270
Author(s):  
Cao Zeng ◽  
Xue Han Hu ◽  
Feng Wei ◽  
Xiao Wei Shi
Keyword(s):  
Return Loss ◽  
High Selectivity ◽  
Power Divider ◽  
Center Frequency ◽  
Differential Mode ◽  
Common Mode ◽  
Mode Suppression ◽  
The Common ◽  
Equal Power ◽  
Good Agreement

AbstractIn this paper, a tunable balanced-to-balanced in-phase filtering power divider (FPD) is designed, which can realize a two-way equal power division with high selectivity and isolation. A differential-mode (DM) passband with a steep filtering performance is realized by applying microstrip stub-loaded resonators (SLRs). Meanwhile, six varactors are loaded to the SLRs to achieve the center frequency (CF) and bandwidth adjustment, respectively. U-type microstrip lines integrated with stepped impedance slotline resonators are utilized as the differential feedlines, which suppress the common-mode (CM) intrinsically, making the DM responses independent of the CM ones. A tuning center frequency from 3.2 to 3.75 GHz and a fractional bandwidth (12.1–17.6%) with more than 10 dB return loss and less than 2.3 dB insertion loss can be achieved by changing the voltage across the varactors. A good agreement between the simulated and measured results is observed. To the best of authors' knowledge, the proposed balanced-to-balanced tunable FPD is first ever reported.

Monitoring Tissue Temperature Using Antenna Return Loss Spectrum

2021 ◽  
Vol 30 ◽  
pp. S257
Author(s):  
E. Yang ◽  
V. Tran ◽  
T. Barry ◽  
A. McEwan ◽  
P. Qian
Keyword(s):  
Return Loss ◽  
Tissue Temperature

scholarly journals Inverted F Type Antenna Design for the Cattle Activity and Estrus Detection Sensor Module

2020 ◽  
Vol 11 (1) ◽  
pp. 298
Author(s):  
Youchung Chung
Keyword(s):  
Radio Frequency ◽  
Return Loss ◽  
Antenna Design ◽  
Sensor Module ◽  
Estrus Detection ◽  
Communication Module ◽  
Frequency Module ◽  
Rf Transmission ◽  
Main Station

In this paper, an inverted F type antenna (IFA) for ZigBee communication of a sensor board has been designed and optimized, and it replaces the chip antenna on an RF (Radio Frequency) module that is not performing well enough for the ZigBee communication. The sensor board detects cattle behavior and identifies the breeding (estrus) period and transmits the data to the main station by the RF (Radio Frequency) module and IFA antenna. The proposed and optimized TRx (transmitting/receiving) IFA antenna of the ZigBee communication module has a return loss of −19 dB and a gain of 1.6 dB at 2.45 GHz. The size is about 2.5 × 0.5 cm in width and vertical length, and the height is 0.55 cm. The strength of signals with the chip antenna and the IFA antenna have been measured and compared. There is about a 20 dB enhancement with the IFA antenna compared to the chip antenna. The antenna is designed and applied to the RF transmission and reception (TRx) module. This antenna and sensor module can be applied to livestock in general as well as cattle.

Sign in / Sign up

Export Citation Format

Share Document