scholarly journals The Performance Evaluation on Co-Digestion of Domestic Sewage Sludge and Food Waste for Methane Yield and Kinetics Analysis

2021 ◽  
Vol 13 (3) ◽  
Author(s):  
Siti Mariam Sulaiman ◽  
◽  
Roslinda Seswoya ◽  
Keyword(s):  
Anaerobic Digestion ◽  
Sewage Sludge ◽  
Food Waste ◽  
Methane Production ◽  
Test System ◽  
Domestic Sewage ◽  
Methane Yield ◽  
Methane Potential ◽  
Methane Production Rate ◽  
Bmp Test

Sewage sludge and food waste; are organic wastes suitable for the anaerobic digestion. However, the digestion of sewage sludge and food waste as solely substrate is having a drawback in term of methane yield. Therefore, many researchers combined these two wastes as a co-substrate and used in co-digestion. This study focused to evaluate the anaerobic co-digestion of domestic sewage sludge (in form of primary and secondary sewage sludge) with food waste under mesophilic temperature in a batch assay. Two series of batch biochemical methane potential (BMP) test were conducted using the Automatic Methane Potential Test System (AMPTS II). Each set are labelled with BMP 1(PSS:FW) and BMP 2 (SSS:FW). The BMP tests were monitored automatically until the methane production is insignificant. Using the data observed in the laboratory, the kinetic paremeters were calculated. Also, the First-order and Modified Gompertz modeling were included to predict the anaerobic digestion performance. Finding showed that BMP 1(PSS:FW) have better performance with respect to the higher ultimate methane yield and methane production rate as compared to BMP 2 (SSS:FW). Besides, the kinetic parameters from laboratory work and modeling were slightly different. In which the kinetic paremetes from modelling is lesser. However, both modelling are well fitted to the experimental data with high correlation coefficient, R2 ranged from 0.993 to 0.997.

scholarly journals Methane Potential from the Digestion of Food Waste in a Batch Reactor

2018 ◽  
Vol 7 (3.23) ◽  
pp. 36 ◽  
Author(s):  
Roslinda Seswoya ◽  
Ahmad Tarmizi Abdul Karim ◽  
Nur Aiza Darnak ◽  
Muhammad Fahmi Abd Rahman
Keyword(s):  
Food Waste ◽  
Methane Production ◽  
Yield Curve ◽  
Batch Reactor ◽  
Laboratory Data ◽  
Test System ◽  
Methane Yield ◽  
Lag Phase ◽  
Methane Potential ◽  
Bmp Test

The anaerobic digestibility of a targeted substrate, measured as methane yield is conducted via biochemical methane potential (BMP). In this study, the batch BMP test was conducted using Automatic Methane Potential Test System (AMPTS II) for 25 days and focused on the methane production from the digestion of food waste (FW, in the form of raw and diluted) at inoculum to substrate ratio (I/S) ratio of 2:0 and under mesophilic temperature.  The results showed that solids (TS and VS) concentration reduced significantly due to the       dilution. The ultimate methane yields from the digestion of raw FW and diluted FW were 1891.91ml CH4/gVS and 1983.96 ml CH4/gVS respectively. This showed that the dilution significantly improved the methane yield. In addition, the lag phase of the methane yield curve for both BMP tests was less than one (1) day, showing the good biodegradability of FW. The kinetic methane production from laboratory data and Modified Gompertz modelling fitted well. However, the kinetic equation parameters such as Mo, Rm and l from the model were slightly lower based on the observation of the laboratory data. 

scholarly journals Optimisation of C:N Ratio for Co-Digested Processed Industrial Food Waste and Sewage Sludge Using the BMP Test

2011 ◽  
Vol 9 (1) ◽  
Author(s):  
Zuhaib Siddiqui ◽  
N.J. Horan ◽  
Kofi Anaman
Keyword(s):  
Sewage Sludge ◽  
Food Waste ◽  
Biogas Production ◽  
C:N Ratio ◽  
Methane Yield ◽  
Biochemical Methane Potential ◽  
Volatile Solids ◽  
Methane Potential ◽  
Biomethane Production ◽  
Bmp Test

Biomethane production from processed industrial food waste (IFW) in admixture with sewage sludge (primary and waste activated sludge: PS and WAS) was evaluated at a range of C:N ratios using a standard biochemical methane potential (BMP) test. IFW alone had a C:N of 30 whereas for WAS it was 5.4 and thus the C:N ratio of the blends fell in that range. Increasing the IFW content in mix improves the methane potential by increasing both the cumulative biogas production and the rate of methane production. Optimum methane yield 239 mL/g VSremoved occurred at a C:N ratio of 15 which was achieved with a blend containing 11 percent (w/w) IFW. As the fraction of IFW in the blend increased, volatile solids (VS) destruction was increased and this led to a reduction in methane yield and amount of production. The highest destruction of volatile solids of 93 percent was achieved at C:N of 20 followed by C:N 30 and 15. A shortened BMP test is adequate for evaluating optimum admixtures.

Determination of methane yield of cellulose using different experimental setups

2014 ◽  
Vol 70 (4) ◽  
pp. 599-604 ◽  
Author(s):  
Bing Wang ◽  
Ivo Achu Nges ◽  
Mihaela Nistor ◽  
Jing Liu
Keyword(s):  
Water Column ◽  
Test System ◽  
Methane Yield ◽  
Biochemical Methane Potential ◽  
Methane Potential ◽  
Bmp Test ◽  
Potential Test

In this work, biochemical methane potential (BMP) tests with cellulose as a model substrate were performed with the aid of three manually operated or conventional experimental setups (based on manometer, water column and gas bag) and one automated apparatus specially designed for analysis of BMP. The methane yields were 340 ± 18, 354 ± 13, 345 ± 15 and 366 ± 5 ml CH4/g VS obtained from experimental setups with manometer, water column, gas bag, and automatic methane potential test system, which corresponded to a biodegradability of 82, 85, 83 and 88% respectively. The results demonstrated that the methane yields of cellulose obtained from conventional and automatic experimental setups were comparable; however, the methane yield obtained from the automated apparatus showed greater precision. Moreover, conventional setups for the BMP test were more time- and labour-intensive compared with the automated apparatus.

Improving methane production and anaerobic digestion stability of food waste by extracting lipids and mixing it with sewage sludge

2017 ◽  
Vol 244 ◽  
pp. 996-1005 ◽  
Author(s):  
Dalal E. Algapani ◽  
Jing Wang ◽  
Wei Qiao ◽  
Min Su ◽  
Andrea Goglio ◽  
...  
Keyword(s):  
Anaerobic Digestion ◽  
Sewage Sludge ◽  
Food Waste ◽  
Methane Production

Anaerobic digestion of sunflower oil cake: a current overview

2013 ◽  
Vol 67 (2) ◽  
pp. 410-417 ◽  
Author(s):  
M. A. De la Rubia ◽  
V. Fernández-Cegrí ◽  
F. Raposo ◽  
R. Borja
Keyword(s):  
Anaerobic Digestion ◽  
Sunflower Oil ◽  
Physical Structure ◽  
Methane Yield ◽  
Organic Loading Rate ◽  
Biochemical Methane Potential ◽  
In Series ◽  
Methane Potential ◽  
Bmp Test ◽  
Sunflower Oil Cake

Due to the chemical and physical structure of a lignocellulosic biomass, its anaerobic digestion (AD) is a slow and difficult process. In this paper, the results obtained from a batch biochemical methane potential (BMP) test and fed-batch mesophilic AD assays of sunflower oil cake (SuOC) are presented. Taking into account the low digestibility shown during one-stage experiments the methane yield decreased considerably after increasing the organic loading rate (OLR) from 2 to 3 g VS L−1 d−1, SuOC was subjected to a two-stage AD process (hydrolytic-acidogenic and methanogenic stages), in two separate reactors operating in series where the methanogenic stage became acidified (with >1,600 mg acetic acid L−1) at an OLR as low as 2 g VS L−1 d−1. More recently, BMP assays were carried out after mechanical, thermal, and ultrasonic pre-treatments to determine the best option on the basis of the methane yield obtained.

Effect of three pretreatment techniques on the chemical composition and on the methane yields of Opuntia ficus-indica (prickly pear) biomass

2017 ◽  
Vol 36 (1) ◽  
pp. 17-29 ◽  
Author(s):  
PS Calabrò ◽  
E Catalán ◽  
A Folino ◽  
A Sánchez ◽  
D Komilis
Keyword(s):  
Chemical Composition ◽  
Methane Production ◽  
Lignin Content ◽  
Alkaline Treatment ◽  
Methane Yield ◽  
Opuntia Ficus Indica ◽  
Methane Generation ◽  
Methane Potential ◽  
Methane Production Rate ◽  
Experimental Values

Opuntia ficus-indica (OFI) is an emerging biomass that has the potential to be used as substrate in anaerobic digestion. The goal of this work was to investigate the effect of three pretreatment techniques (thermal, alkaline, acidic) on the chemical composition and the methane yield of OFI biomass. A composite experimental design with three factors and two to three levels was implemented, and regression modelling was employed using a total of 10 biochemical methane potential (BMP) tests. The measured methane yields ranged from 289 to 604 NmL/gVSadded; according to the results, only the acidic pretreatment (HCl) was found to significantly increase methane generation. However, as the experimental values were quite high with regards to the theoretical methane yield of the substrate, this effect still needs to be confirmed via further research. The alkaline pretreatment (NaOH) did not noticeably affect methane yields (an average reduction of 8% was recorded), despite the fact that it did significantly reduce the lignin content. Thermal pretreatment had no effect on the methane yields or the chemical composition. Scanning electron microscopy images revealed changes in the chemical structure after the addition of NaOH and HCl. Modelling of the cumulated methane production by the Gompertz modified equation was successful and aided in understanding kinetic advantages linked to some of the pretreatments. For example, the alkaline treatment (at the 20% dosage) at room temperature resulted to a μmax (maximum specific methane production rate [NmLCH4/(gVSadded·d)]) equal to 36.3 against 18.6 for the control.

Hydrogen and methane production in a two-stage anaerobic digestion system by co-digestion of food waste, sewage sludge and glycerol

2018 ◽  
Vol 76 ◽  
pp. 339-349 ◽  
Author(s):  
Fabrícia M.S. Silva ◽  
Claudio F. Mahler ◽  
Luciano B. Oliveira ◽  
João P. Bassin
Keyword(s):  
Anaerobic Digestion ◽  
Sewage Sludge ◽  
Food Waste ◽  
Methane Production ◽  
Two Stage ◽  
Waste Sewage Sludge

scholarly journals Effect of Pasteurisation on Methane Yield from Food Waste and Other Substrates in Anaerobic Digestion

Processes ◽  
2020 ◽  
Vol 8 (11) ◽  
pp. 1351
Author(s):  
Yue Zhang ◽  
Sigrid Kusch-Brandt ◽  
Sonia Heaven ◽  
Charles J. Banks
Keyword(s):  
Anaerobic Digestion ◽  
Food Waste ◽  
Statistical Significance ◽  
Methane Yield ◽  
Volatile Components ◽  
Cattle Slurry ◽  
Animal Blood ◽  
Potato Waste ◽  
Methane Potential ◽  
The Difference

The effect of pasteurisation and co-pasteurisation on biochemical methane potential values in anaerobic digestion (AD) was studied. Pasteurisation prior to digestion in a biogas plant is a common hygienisation method for organic materials which contain or have been in contact with animal by-products. Tests were carried out on food waste, slaughterhouse waste, animal blood, cattle slurry, potato waste, card packaging and the organic fraction of municipal solid waste (OFMSW); pasteurisation at 70 °C for 1 h was applied. Pasteurisation had increased the methane yields of blood (+15%) and potato waste (+12%) only, which both had a low content of structural carbohydrates (hemi-cellulose and cellulose) but a particularly high content of either non-structural carbohydrates such as starch (potato waste) or proteins (blood). With food waste, card packaging and cattle slurry, pasteurisation had no observable impact on the methane yield. Slaughterhouse waste and OFMSW yielded less methane after pasteurisation in the experiments (but statistical significance of the difference between pasteurised and unpasteurised slaughterhouse waste or OFMSW was not confirmed in this work). It is concluded that pasteurisation can positively impact the methane yield of some specific substrates, such as potato waste, where heat-treatment may induce gelatinisation with release of the starch molecules. For most substrates, however, pasteurisation at 70 °C is unlikely to increase the methane yield. It is unlikely to improve biodegradability of lignified materials, and it may reduce the methane yield from substrates which contain high contents of volatile components. Furthermore, in this experimental study, the obtained methane yield was unaffected by whether the substrates were pasteurised individually and then co-digested or co-pasteurised as a mixture before batch digestion.

Study on Solid-State Anaerobic Co-Digestion with Distiller’s Grains and Food Waste for Methane Production

2012 ◽  
Vol 485 ◽  
pp. 306-309
Author(s):  
Li Hong Wang ◽  
Qun Hui Wang ◽  
Wei Wei Cai
Keyword(s):  
Anaerobic Digestion ◽  
Solid State ◽  
Synergistic Effect ◽  
Food Waste ◽  
Methane Production ◽  
Waste Treatment ◽  
Biogas Production ◽  
Methane Yield ◽  
Kitchen Waste ◽  
Distiller's Grains

Solid-state anaerobic digestion (SSAD) of distiller’s grains (DG) and kitchen waste (KW) for biogas was investigated. Six DG to KW ratios of 10/1, 8/1, 6/1, 4/1, 1/0, and 0/1 was used. The results showed that in 48 digestion days the co-digestion with DG to KW ratio of 8:1 obtained the highest methane yield of 159.74mL/gTS, TS and VS reductions of 58.7% and 71.8%, hemicellulase, cellulose and lignin reductions of 46.7%, 45.4% and 4.0%. Compared to mono-digestions of DG or KW, co-digestion of DG and FW had a good synergistic effect. It indicated that SSAD of cellulosic-based waste and food waste could be one of the options for efficient biogas production and waste treatment

Sign in / Sign up

Export Citation Format

Share Document