scholarly journals Mixing Effectiveness of Various Damper-Plenum Configurations

2008 ◽  
Vol 42 (2008) ◽  
pp. 18-22 ◽  
Author(s):  
H. J. Sauer ◽  
P. Hande ◽  
F. Finaish

Improper mixing of outside air and return air streams in building air conditioning systems has been recognized for years. The problems may lead to nuisance cycling, frequent freeze-stat trips and serious consequences of a frozen or ruptured conditioning coil. It was thought that typical solutions for the problem usually consist of preferred placement of outside air and return air duct penetrations to the mixing box, manipulation of the inlet damper angles and velocity ratio between the outside air and return air streams and the insertion of static flow mixers in the mixing box to help improve the thermal stratification. This paper reports the results of a computational fluid dynamics (CFD) study conducted as a follow-up to an experimental study conducted at the Ruskin Laboratory in Grandview, Missouri, sponsored by the American Society of Heating, Refrigerating and Air-Conditioning Engineers (ASHRAE). The CFD results indicated that the most significant improvement in mixing performance with minimum increase in pressure drop and energy use is achieved by expanding the mixing plenum. Effectiveness increased from 39 percent to 67 percent with less than a 0.1 inch of water additional pressure drop. However, optimization of relative plenum dimensions and baffle size and placement awaits additional CFD simulations and full scale validation.

Author(s):  
Milton Meckler

What does remain a growing concern for many users of Data Centers is their continuing availability following the explosive growth of internet services in recent years, The recent maximizing of Data Center IT virtualization investments has resulted in improving the consolidation of prior (under utilized) server and cabling resources resulting in higher overall facility utilization and IT capacity. It has also resulted in excessive levels of equipment heat release, e.g. high energy (i.e. blade type) servers and telecommunication equipment, that challenge central and distributed air conditioning systems delivering air via raised floor or overhead to rack mounted servers arranged in alternate facing cold and hot isles (in some cases reaching 30 kW/rack or 300 W/ft2) and returning via end of isle or separated room CRAC units, which are often found to fight each other, contributing to excessive energy use. Under those circumstances, hybrid, indirect liquid cooling facilities are often required to augment above referenced air conditioning systems in order to prevent overheating and degradation of mission critical IT equipment to maintain rack mounted subject rack mounted server equipment to continue to operate available within ASHRAE TC 9.9 prescribed task psychometric limits and IT manufacturers specifications, beyond which their operational reliability cannot be assured. Recent interest in new web-based software and secure cloud computing is expected to further accelerate the growth of Data Centers which according to a recent study, the estimated number of U.S. Data Centers in 2006 consumed approximately 61 billion kWh of electricity. Computer servers and supporting power infrastructure for the Internet are estimated to represent 1.5% of all electricity generated which along with aggregated IT and communications, including PC’s in current use have also been estimated to emit 2% of global carbon emissions. Therefore the projected eco-footprint of Data Centers into the future has now become a matter of growing concern. Accordingly our paper will focus on how best to improve the energy utilization of fossil fuels that are used to power Data Centers, the energy efficiency of related auxiliary cooling and power infrastructures, so as to reduce their eco-footprint and GHG emissions to sustainable levels as soon as possible. To this end, we plan to demonstrate significant comparative savings in annual energy use and reduction in associated annual GHG emissions by employing a on-site cogeneration system (in lieu of current reliance on remote electric power generation systems), introducing use of energy efficient outside air (OSA) desiccant assisted pre-conditioners to maintain either Class1, Class 2 and NEBS indoor air dew-points, as needed, when operated with modified existing (sensible only cooling and distributed air conditioning and chiller systems) thereby eliminating need for CRAC integral unit humidity controls while achieving a estimated 60 to 80% (virtualized) reduction in the number servers within a existing (hypothetical post-consolidation) 3.5 MW demand Data Center located in southeastern (and/or southern) U.S., coastal Puerto Rico, or Brazil characterized by three (3) representative microclimates ranging from moderate to high seasonal outside air (OSA) coincident design humidity and temperature.


Processes ◽  
2021 ◽  
Vol 9 (10) ◽  
pp. 1785
Author(s):  
Ranjan Pratap Singh ◽  
Ranadip K. Das

A rotary desiccant-based air-conditioning system is a heat-driven hybrid system which combines different technologies such as desiccant dehumidification, evaporative cooling, refrigeration, and regeneration. This system has an opportunity to utilize low-grade thermal energy obtained from the sun or other sources. In this paper, the basic principles and recent research developments related to rotary desiccant-based cooling systems are recalled and their applications and importance are summarized. It is shown that with novel system configurations and new desiccant materials, there is great potential for improving the performance and consistency of rotary desiccant systems; at the same time, the use of solar energy for regeneration purposes can minimize the operating cost to a great extent. Some examples are presented to demonstrate how rotary desiccant air conditioning can be a promising solution for replacing traditional vapor-compression air-conditioning systems. Recent advances and ongoing research related to solar-powered hybrid rotary desiccant cooling systems are also summarized. The hybrid systems make use of a vapor-compression system in order to have better operational flexibility. These systems, although they consume electrical energy, use solar energy as the principal source of energy, and hence, significant savings of premium energy can be obtained compared to conventional vapor-compression systems. However, further research and development are required in order to realize the sustainable operation of solar rotary desiccant air-conditioning systems, as solar energy is not steady. Reductions in capital cost and size, along with improvements in efficiency and reliability of the system is still needed for it to become a player in the market of air conditioning.


2020 ◽  
Vol 28 (01) ◽  
pp. 2050004 ◽  
Author(s):  
Ahmad M. Abubaker ◽  
Yousef S. H. Najjar ◽  
Adnan Darwish Ahmad

This study introduces the design of a novel condenser for air conditioning systems. Enhancement of performance of the system was manifested by increasing the coefficient of performance (COP), decreasing the pressure drop and the power consumed by the refrigerant compressor and the cooling water pump. The design consists of an adiabatic double-pipe heat exchanger with longitudinal rectangular fins. This model can enhance heat transfer coefficient and expose more area per unit length. This novel design supersedes other conventional condenser designs by 4.7% higher COP, 8.2% lower water pressure drop, 4.68% lower compressor power. Two refrigerants have been examined in the study; R-134a which is used in commercial and industrial chillers and R-1234ze which has low global warming potential.


Author(s):  
D. Mahboubi ◽  
M. H. Saidi

Hot water heating coils are key components in air conditioning systems undergo heat transfer. The most widely used exchangers (coils) take the form of fin and tube configuration in association with the application of air conditioning systems. In this research, thermodynamic modeling and mathematical optimization of hot water heating coils at steady conditions, approaching minimum energy consumption are achieved. The modeling procedure for heating coils is done based on the log mean temperature difference (LMTD) method. The objective function for optimization is pressure drop of air crossing coil per heating load of the system. This unction comprises all thermal and geometrical parameters of the coils such as coil surface area, number of rows, fin spacing and air side pressure drop of the coil. The objective function is minimized using Lagrange multipliers method. The optimization results are composed of minimum pressure drop, optimum surface area, optimum number of rows and fin spacing. The effects of varying the heating load, fin efficiency and the surface area of the coils on optimum behavior of them are investigated as well.


Author(s):  
David Zietlow ◽  
Dan A. Spurgeon

Original equipment manufacturers are looking for ways to reduce the product development cycle. A tool to reduce this time in the design of air conditioning systems is introduced in this paper. This is done by using a semitheoretical model of each of the components of a system. The semitheoretical model has the advantage of reducing the number of geometrical inputs that need to be specified when compared with a “theoretical” model. This paper focuses on the most complex of the components—the evaporator. A tube and fin evaporator was successfully modeled and validated. The model was tuned using supplier component data (Luvata, 2005, Heatcraft Evaporator—Version 3.07.05.122 B-DHLEX.EVP) for the evaporator. The tuned accuracy of heat transfer rate and pressure drop, both air- and refrigerant-side, was within 5% over the range of conditions representative of air conditioning applications.


Sign in / Sign up

Export Citation Format

Share Document