The combined effect of cutting speed and feed on the power characteristics in the time of drilling

2021 ◽  
Vol 2021 (12) ◽  
pp. 31-36
Author(s):  
Rasul Guseinov ◽  
Ludmila Sultanova ◽  
Konstantin Sakhno ◽  
Anatoliy Ruban
Keyword(s):  
Cutting Speed ◽  
Pair Interaction ◽  
Planning Method ◽  
Combined Effect ◽  
The Other ◽  
Experiment Planning ◽  
Research Results ◽  
Power Characteristics

The analysis of works devoted to the study of power characteristics in the course of drilling is presented. Research results of the combined effect of cutting speed and feed on the power characteristics when drilling steel parts 45 using the experiment planning method according to plan 22 are presented. The existence of pair interaction is shown, which made it possible to assess the power of influence of one of the factors depending on the level where the other is located.

The Structure of Wiggins' Interpersonal Circumplex: Cross-Cultural Studies

1999 ◽  
Vol 15 (3) ◽  
pp. 196-205 ◽  
Author(s):  
Rosario Martínez-Arias ◽  
Fernando Silva ◽  
Ma Teresa Díaz-Hidalgo ◽  
Generós Ortet ◽  
Micaela Moro
Keyword(s):  
Cultural Studies ◽  
Cross Cultural ◽  
The Other ◽  
Spanish Version ◽  
Interpersonal Circumplex ◽  
Research Groups ◽  
Independent Research ◽  
Research Results ◽  
Cross Cultural Studies

Summary: This paper presents the results obtained in Spain with The Interpersonal Adjective Scales of J.S. Wiggins (1995) concerning the variables' structure. There are two Spanish versions of IAS, developed by two independent research groups who were not aware of each other's work. One of these versions was published as an assessment test in 1996. Results from the other group have remained unpublished to date. The set of results presented here compares three sources of data: the original American manual (from Wiggins and collaborators), the Spanish manual (already published), and the new IAS (our own research). Results can be considered satisfactory since, broadly speaking, the inner structure of the original instrument is well replicated in the Spanish version.

ANALISIS VARIABEL YANG BERPENGARUH TERHADAP KINERJA PERUSAHAAN DI BURSA EFEK INDONESIA

2019 ◽  
Author(s):  
SUSENO - SUSENO
Keyword(s):  
Linear Regression ◽  
Multiple Linear Regression ◽  
Stock Exchange ◽  
T Test ◽  
The Other ◽  
Financial Leverage ◽  
F Test ◽  
Research Results ◽  
Independent Variables ◽  
Influential Variable

ANALISIS VARIABEL YANG BERPENGARUH TERHADAP KINERJA PERUSAHAAN DI BURSA EFEK INDONESIAOleh : Suseno STIE SATRIA Purwokerto ABSTRACT The aims of the research are (1) to analyze influence of age, scale, financial leverage, and profitability to performance of firms at The Indonesian Stock Exchange. (2) to determine the most influential variable on the performance of the firms. Hypotheses proposed in this research were: (1) Age, Scales, Financial Leverage, Profitability influences the performance of firms, (2) Age influences the performance of firms, (3) Scales influences the performance of firms, (4) Financial Leverage influences the performance of firms, (5) Profitability influences the performance of firms. Instrument of analysis employed in the research was multiple linear regression with t test and F test.The results of analyses of t test showed that profitability did not influence the performance of the firms. It was indicated by the value of computed t which was smaller than the value of t table. Meanwhile, the t test of age, scale and financial leverage indicated that the value of computed t > t table. It means that these variables (scale and financial leverage) influenced the performance of the firms. The F test showed that the independent variables of age, scale, financial leverage and profitability as a whole significantly influenced the performance of the firms. It was indicated by the calculated F > the value of F table, the value the age computed t which was smaller than the value of -t table..Based on the research results that age and profitability do not influence the performance of the firms, it is suggested that investors should not pay any attention to those variables. On the other hand, they should pay attention to the variables of scale and financial leverage. It is recommended that for further research should include longer periode of the sample.

Experimental Determination of Optimal Speeds for Alloy Steels in Plane Turning

2008 ◽  
Author(s):  
T. Srikanth ◽  
V. Kamala
Keyword(s):  
Surface Roughness ◽  
Force Measurement ◽  
Cutting Speed ◽  
Vital Role ◽  
The Other ◽  
Depth Of Cut ◽  
Work Piece ◽  
Material Interface ◽  
Alloy Steels

In machining, speeds play vital role. The operator should know exactly the speed at which machining should be performed to get the required surface finish. In this paper, an attempt is made to determine the optimal cutting speed for machining of alloy steels. Three work piece materials having different hardness are taken and machined using a round nose tool with a coated tip. The tool dynamometer is attached to the tool post for force measurement. Turning operation on the work piece is performed on lathe at four different speeds, keeping the feed and depth of cut constant. Cutting forces acting on the tool, temperature at the tool and material interface are recorded. Power consumed being determined by a wattmeter and surface roughness values are measured. The same procedure is repeated for the other two work-pieces materials and optimal speeds for machining are determined for the three specimens. The results obtained are compared with the theoretical values and found to be very close.

Numerical Simulation Research on the Shape of Top Coal Drawn-Body in Gently Inclined Seam

2012 ◽  
Vol 468-471 ◽  
pp. 2248-2254
Author(s):  
Qiang Li ◽  
Wan Kui Bu ◽  
Hui Xu ◽  
Xiao Bo Song
Keyword(s):  
Numerical Simulation ◽  
Numerical Model ◽  
Random Medium ◽  
Body Movement ◽  
The Other ◽  
Simulation Research ◽  
Research Results ◽  
Shape Equation ◽  
The Difference ◽  
Meso Scale

The numerical model of top coal drawing in gently inclined seam is built based on PFC2d software. By comparing with the theory of drawn-body movement law, it can be obtained that the shape of top coal drawn-body accords with the theory of random medium movement. The research results show that the form of the shape equation of top coal drawn-body is uniform while the top coal caving angle is different. On the other hand, with the difference of top coal caving angle and drawing height, the shape of top coal drawn-body is differential at the meso scale, which depends on the parameters of the shape equation of top coal drawn-body.

scholarly journals Pengujian Zeolit Alam Mordenit Sebagai Penjerap Proses Pendegradasian Kandungan Amonium di dalam Air Tambak

2020 ◽  
Vol 21 (1) ◽  
pp. 49-55
Author(s):  
Nuryoto Nuryoto ◽  
Teguh Kurniawan ◽  
Indar Kustiningsih
Keyword(s):  
Particle Size ◽  
Natural Zeolite ◽  
The Other ◽  
Ammonium Concentration ◽  
Small Fish ◽  
Natural Zeolites ◽  
Absorption Time ◽  
Adsorption Time ◽  
Research Results ◽  
Other Hand

ABSTRACTIndonesia has an abundant quantity of natural zeolites that have not yet been utilized maximally. On the other hand, fishpond farmers have a problem regarding the presence of ammonium in the fishpond water which will negatively impact to survival of fish, especially small fish. To solve this problem, this research was utilizing natural zeolite to degrade ammonium in the fishpond water. This research aimed to test mordenite natural zeolite from Bayah as an adsorbent to collaborate some variables impact to reach more maximal adsorption. The variables that were used to be observed were: mordenite natural zeolite from Bayah as an adsorbent which has been activated by 1-7 N H2SO4 and the other was without activation, ammonium concentration of 80-800 ppm, the particle size of adsorbent of 80 and 150 mesh, stirring speed of 600 and 800 rpm, and without stirring by duration adsorption time of 60 minutes. The research results showed that mordenite natural zeolite after activated was able to adsorb of 100% ammonium, while for the mordenite natural zeolite from Bayah without stirring was of 80%, by the same absorption time. These results will give significant benefits for fishpond farmers to increase their productivity because of the increase in fish survival.Keywords: adsorption, adsorbent, zeolite, amoniumABSTRAKKandungan zeolit alam di Indonesia cukup melimpah dan belum termanfaatkan secara maksimal. Pada sisi lain petani tambak dihadapkan pada masalah terdapatnya kandungan amonium di dalam air tambak, yang akan berdampak negatif bagi keberlangsungan hidup ikan, terutama ikan yang masih kecil. Penelitian ini mencoba memanfaatkan zeolit alam guna mendegradasi kandungan amonium dalam air tambak. Tujuan penelitian ini adalah melakukan pengujian terhadap zeolit alam mordenit dari Bayah sebagai adsorben, baik dilakukan dengan pengadukan maupun tanpa pengadukan, serta mengkolaborasi beberapa variabel yang berpengaruh agar hasil adsorpsi lebih maksimal. Observasi dilakukan dengan zeolit alam mordenit dari Bayah yang telah diaktivasi dengan 1-7 N H2SO4 maupun tanpa aktivasi, rentang konsentrasi larutan amonium 80-800 ppm, ukuran partikel adsorben 80 dan 150 mesh, kecepatan pengadukan 600 dan 800 rpm, dan tanpa pengadukan serta lamanya waktu penyerapan 60 menit. Hasil penelitian menunjukan hasil yang sangat baik, dan secara umum zeolit alam mordenit Bayah teraktivasi telah mampu melakukan adsorpsi amonium sebesar 100%, sedangkan untuk zeolit alam mordenit Bayah tanpa pengadukan sebesar 80% pada waktu adsorpsi yang sama.Kata kunci: adsorpsi, adsorben, zeolit, amonium

scholarly journals Applying transfer entropy approach to investigate the information flow among ASEAN stock markets

2020 ◽  
Vol 4 (1) ◽  
pp. First
Author(s):  
Tran Thi Tuan Anh
Keyword(s):  
Information Flow ◽  
Stock Markets ◽  
Investment Strategy ◽  
The Philippines ◽  
Transfer Entropy ◽  
The Other ◽  
Information Flows ◽  
Research Results ◽  
Region Data ◽  
Asean Countries

This paper uses transfer entropy to measure and identify the information flows between stock markets in the ASEAN region. Data on daily closing stock indices, including Vietnam, the Philippines, Malaysia, Indonesia, Thailand, and Singapore, are collected for the period from March 2012 to October 2019 to calculate these transfer entropies. The research results of this article can be considered in two aspects: one is, how information flow originating from one market will be accepted by other markets and secondly, information flow that markets receive. From the perspective of incoming transfer entropy, Vietnam is the country most affected by information from the other ASEAN markets while Indonesia and Malaysia are the least affected. In terms of outgoing entropy, Thailand is the largest source of information flow to the ASEAN markets. Malaysia and the Philippines are the two countries that receive minor information impact from other countries. The research also reveals that the Singapore stock market is rather separate from the other ASEAN countries. The research results also imply that, for investors and policymakers, defining the information flows among ASEAN stock markets can help to predict market movements, thereby developing a suitable investment strategy or establishing appropriate management policies.

Thermal hardening and calculation of the mathematical model of face milling of parts made of steel 95X18-Sh to improve the quality of the surface layer

2021 ◽  
pp. 200-206
Author(s):  
I.N. Sedinin ◽  
V.F. Makarov
Keyword(s):  
Mathematical Model ◽  
Cutting Speed ◽  
Physical And Mechanical Properties ◽  
Face Milling ◽  
Experiment Planning ◽  
Depth Of Cut ◽  
Machined Surface ◽  
The Mathematical Model ◽  
Full Factorial

It is considered the complex of operations of the technological process for the heat treatment of steel 95X18-Sh, as a result of which the material of the samples increases the hardness to 59...61 HRC, and also improves the physical and mechanical properties. A full-scale full factorial experiment of face milling of samples was carried out using the method of mathematical planning. In the experiments, a high-precision machine and a carbide cutting tool were used. To calculate the values of the roughness function, the following are taken as independent variables: cutting speed, feed per tooth and depth of cut. In order to determine the coefficients of the linear equation, a central compositional orthogonal plan of the second order for three factors was used. A matrix of levels of variation of independent variable factors and a matrix of experiment planning were compiled. A regression analysis of the obtained experimental statistical data was carried out using the Microsoft Excel, Statistica and Wolfram Alpha programs. As a result of the calculations, a mathematical model of the roughness of the machined surface and optimal cutting conditions were determined.

Flank-Wear Model and Optimization of Machining Process and its Control in Turning

1973 ◽  
Vol 187 (1) ◽  
pp. 301-307
Author(s):  
Y. Koren ◽  
J. Ben-Uri
Keyword(s):  
Flank Wear ◽  
Cutting Speed ◽  
The Other ◽  
Machining Process ◽  
Depth Of Cut ◽  
Wear Model ◽  
Speed Change ◽  
Steel Turning ◽  
The One ◽  
Non Linear System

Designing the optimal control for a machine tool necessitates a mathematical model of the cutting process. In the present paper, a flank-wear model was developed for a carbide tool used in steel turning. It yields the relation between the process parameters (cutting speed, feed and depth of cut) on the one hand, and the width of the wear land on the other. In the second stage—the optimization proper—the problem consists of optimizing a non-linear system with the initial, and part of the final, conditions known, and the terminal time not given explicitly. Complexity was reduced by converting from time- to path-derivatives, and the problem was solved using the gradient method, yielding cost differences which are negligible compared with the conventional method. To complete the picture, a motor control system was sought minimizing the error in obeying the speed change command on the one hand, and the path error during simultaneous operation of several feed spindles on the other.

scholarly journals Y25 freight car bogie models properties analysis by means of computer simulations

2018 ◽  
Vol 157 ◽  
pp. 03014 ◽  
Author(s):  
Tomáš Lack ◽  
Juraj Gerlici
Keyword(s):  
Tangential Stress ◽  
Computer Simulations ◽  
Simulation Analysis ◽  
The Other ◽  
Bogie Frame ◽  
Friction Dampers ◽  
Research Results ◽  
Railway Wagon ◽  
Freight Car ◽  
Railway Wheels

The article deals with the results of the simulation analysis of a railway wagon bogie model. We analysed four freight wagon bogie variants for its dynamics properties research. The bogie models correspond in general to the Y25 bogie concept. The models were created in SIMPACK software enhanced by the RAIL module. From the research results depicted in the graphs we found out, that the newly designed bogie variant gives the best results when compared to the other analysed versions. The newly designed model consists of a standard Y25 bogie frame with two Lenoire friction dampers. This bogie is equipped with longitudinal linkages on both sides. These linkages are completed with a radial torsion binding, torsion rod, between side bogie parts. The contact of railway wheels and rails generates active forces affecting the surface contact, affecting the size of the normal and tangential stress, wear surfaces of the wheel/rail, or directly the size of the derailment.

Sign in / Sign up

Export Citation Format

Share Document