scholarly journals Mineral Preparation Using Rod Mill for Mineral Galena Characterization

2021 ◽  
Vol 1 (1) ◽  
pp. 355-362
Author(s):  
Riria Zendy Mirahati ◽  
Yasmina Amalia ◽  
Mochamad Juliyanto ◽  
Lintang Larasati Adi Putri
Keyword(s):  
Grain Size ◽  
Electron Microscope ◽  
Scanning Electron Microscope ◽  
Grinding Process ◽  
X Ray Diffraction ◽  
Mineral Concentration ◽  
X Ray ◽  
Concentration Process ◽  
Mineral Characterization ◽  
Scanning Electron

Galena mineral preparation was carried out for mineral characterization. The mineral characterization carried out included XRD (X-Ray Diffraction), XRF (X-Ray Fluorescence), SEM-EDS (Scanning Electron Microscope-Energy Dispersive X-Ray). The preparation of galena minerals begins with the process of reducing the grain size including crushing and grinding. The results of crushing and grinding are then separated based on grain size using a sieve or siever to get a grain size of -200 mesh. The grinding process using a rod mill needs to be timed, so that the results are not too fine which is causing the recovery in the mineral concentration process to be low.

Study on the Properties of Doped La in BaBi4Ti4O15 Ceramic

2007 ◽  
Vol 26-28 ◽  
pp. 243-246
Author(s):  
Xing Hua Yang ◽  
Jin Liang Huang ◽  
Xiao Wang ◽  
Chun Wei Cui
Keyword(s):  
Crystal Structure ◽  
Grain Size ◽  
Electron Microscope ◽  
Scanning Electron Microscope ◽  
Sintering Temperature ◽  
Solid Phase ◽  
X Ray Diffraction ◽  
X Ray ◽  
Lanthanum Content ◽  
Scanning Electron

BaBi4-xLaxTi4O15 (BBLT) ceramics were prepared by conventional solid phase sintering ceramics processing technology. The crystal structure and the microstructure were detected by X-ray diffraction (XRD) and scanning electron microscope (SEM). The XRD analyses show that La3+ ions doping did not change the crystal structure of BBT ceramics. The sintering temperature increased from 1120°C to 1150°C with increasing Lanthanum content from 0 to 0.5, but it widened the sintering temperature range from 20°C to 50°C and refined the grain size of the BBT ceramic. Additionally, polarization treatment was performed and finally piezoelectric property was measured. As a result, the piezoelectric constant d33 of the 0.1at.% doped BBLT ceramics reached its highest value about 22pc/N at polarizing electric field of 8kV/mm and polarizing temperature of 120°C for 30min.

PENGGUNAAN TiO2 PARTIKEL NANO HASIL SINTESIS BERBASIS AIR MENGGUNAKAN METODA SOL-GEL PADA BAHAN KAPAS SEBAGAI APLIKASI UNTUK TEKSTIL ANTI UV

Arena Tekstil ◽  
2013 ◽  
Vol 28 (1) ◽  
Author(s):  
Maya Komalasari ◽  
Bambang Sunendar
Keyword(s):  
Fourier Transform ◽  
Electron Microscope ◽  
Scanning Electron Microscope ◽  
Sol Gel ◽  
Crosslinking Agent ◽  
X Ray Diffraction ◽  
Nano Tio2 ◽  
X Ray ◽  
Infra Red ◽  
Scanning Electron

Partikel nano TiO2 berbasis air dengan pH basa telah berhasil disintesis dengan menggunakan metode sol-gel dan diimobilisasi pada kain kapas dengan menggunakan kitosan sebagai zat pengikat silang. Sintesis dilakukan  dengan prekursor TiCl4 pada konsentrasi 0,3 M, 0,5 M dan 1 M, dan menggunakan templat kanji dengan proses kalsinasi pada suhu 500˚C selama 2 jam. Partikel nano TiO2 diaplikasikan ke kain kapas dengan metoda pad-dry-cure dan menggunakan kitosan sebagai crosslinking agent. Berdasarkan hasil Scanning Electron Microscope (SEM),diketahui bahwa morfologi partikel TiO2 berbentuk spherical dengan ukuran nano (kurang dari 100 nm). Karakterisasi X-Ray Diffraction (XRD) menunjukkan adanya tiga tipe struktur kristal utama, yaitu (100), (101) dan (102) dengan fasa kristal yang terbentuk adalah anatase dan rutile. Pada karakterisasi menggunakan SEM terhadap serbuk dari TiO2 yang telah diaplikasikan ke permukaan kain kapas, terlihat adanya imobilisasi partikel nano TiO2 melalui ikatan hidrogen silang dengan kitosan pada kain kapas. Hasil analisa tersebut kemudian dikonfirmasi dengan FTIR (Fourier Transform Infra Red) yang hasilnya memperlihatkan puncak serapan pada bilangan gelombang 3495 cm-1, 2546 cm-1, dan 511 cm-1,  yang masing-masing diasumsikan sebagai adanya vibrasi gugus fungsi O-H, N-H dan Ti-O-Ti. Hasil SEM menunjukkan pula bahwa kristal nano yang terbentuk diantaranya adalah fasa rutile , yang berdasarkan literatur terbukti dapatberfungsi sebagai anti UV.

Effect of the Neodymium Content on Mechanical Properties of the Electro-Brush Plated Nano-Al2O3/Ni Composite Coating

2012 ◽  
Vol 525-526 ◽  
pp. 277-280
Author(s):  
Guo Jin ◽  
Xiu Fang Cui ◽  
Er Bao Liu ◽  
Qing Fen Li
Keyword(s):  
Mechanical Properties ◽  
Rare Earth ◽  
Electron Microscope ◽  
Scanning Electron Microscope ◽  
Composite Coating ◽  
Nanoindentation Test ◽  
X Ray Diffraction ◽  
X Ray ◽  
Small Cracks ◽  
Scanning Electron

The effect of the neodymium content on mechanical properties of the electro-brush plated nanoAl2O3/Ni composite coating was investigated in this paper. The microstructure and phase structure were studied with scanning electron microscope (SEM) and X-ray diffraction (XRD). The hardness and abrasion properties of several coatings with different neodymium content were studied by nanoindentation test and friction / wear experiment. Results show that the coatings are much finer and more compact when the neodymium was added, and the hardness and abrasion property of the coatings with neodymium were improved obviously. Besides, the small cracks conduced by the upgrowth stress in the coatings were ameliorated when the rare earth neodymium was added. The improvement mechanism was further discussed.

Effect of Briquetting Pressure on the Performance of In Situ Formed Sialon in Al2O3-C Refractory Bricks

2014 ◽  
Vol 881-883 ◽  
pp. 1049-1052 ◽  
Author(s):  
Nai Peng ◽  
Cheng Ji Deng ◽  
Hong Xi Zhu
Keyword(s):  
Electron Microscope ◽  
Scanning Electron Microscope ◽  
X Ray Diffraction ◽  
X Ray ◽  
Z Value ◽  
Refractory Bricks ◽  
Scanning Electron

In this paper, the effects of briquetting pressure on the performance of in-situ formed Sialon in Al2O3-C refractory bricks are investigated. The phase compositions and microstructure of the Al2O3-C refractory were investigated by X-ray diffraction (XRD) and scanning electron microscope (SEM).The results show the briquetting pressure hardly has effect on the phase of the sintered specimens, two new phases of Sialon with a Z value of 2 and SiC formed. The micrographs of Sialon crystals have the shape of both column and tabular column, but with a cone tip in the specimens sintered at 200MPa and 300MPa and smooth tip in specimens sintered at 400MPa and 500MPa.

Sintering Process of Nd:YAG Transparent Ceramic

2013 ◽  
Vol 281 ◽  
pp. 475-479
Author(s):  
Bo Wang ◽  
Quan Xi Cao ◽  
Guang Xu ◽  
Sen Tian
Keyword(s):  
Grain Size ◽  
Electron Microscope ◽  
Scanning Electron Microscope ◽  
Crystal Structures ◽  
Heating Rate ◽  
Optical Transmittance ◽  
Sintering Process ◽  
X Ray ◽  
Polycrystalline Ceramics ◽  
Scanning Electron

1.0at% Nd:YAG polycrystalline ceramics were sintered at 1420°C, 1500°C, 1600°C and 1730°C respectively by different heating rate (1°C/min and 5°C/min). The crystal structures were indexed by X-ray diffractometer (XRD). The microstructure and the grain size of the samples were characterized by scanning electron microscope (SEM). The optical transmittance spectra of the samples were measured using V-570 UV spectrophotometer. The sintering process of Nd:YAG ceramics and the effect of heating rate on the microstructure of samples have been investigated.

Effect of Nickel on Titanium Carbide Synthesized via Tungsten Inert Gas (TIG) Method

2012 ◽  
Vol 620 ◽  
pp. 384-388
Author(s):  
Sharifah Aishah Syed Salim ◽  
Julie Juliewatty Mohamed ◽  
Zainal Arifin Ahmad ◽  
Zainal Arifin Ahmad
Keyword(s):  
Electron Microscope ◽  
Scanning Electron Microscope ◽  
Powder Mixture ◽  
Raw Material ◽  
Inert Gas ◽  
X Ray Diffraction ◽  
X Ray ◽  
Arc Melting ◽  
Elemental Powder Mixture ◽  
Scanning Electron

Numerous methods have been used to produce high purity TiC. There is no previous study has been reported on the formation using single elemental powders of Titanium (Ti) and Carbon (C) with addition Nickel (Ni) by tungsten inert gas (TIG) weld method. In this work, TiC was synthesized via TIG method by arc melting elemental powder mixture of Ti and C at ~5 second (s) and 80 ampere (A). The effect Ni contents on TiC formation was investigated. The mixed raw material was ball milled for 24 hours followed by synthesis via TIG method. The arced samples were characterized by X-ray diffraction (XRD) and Scanning electron microscope (SEM). It was revealed, that small amount of Ni additive to the metal powder allows the production of dense and tough TiC.

scholarly journals Supplementary X-ray studies of the Ni-Sn-Bi system

2007 ◽  
Vol 43 (2) ◽  
pp. 141-150 ◽  
Author(s):  
G.P. Vassilev ◽  
K.I. Lilova ◽  
J.C. Gachon
Keyword(s):  
Electron Microscope ◽  
Scanning Electron Microscope ◽  
Phase Equilibria ◽  
Ternary Compound ◽  
Approximate Formula ◽  
Ternary Phase ◽  
X Ray Diffraction ◽  
X Ray ◽  
Diffraction Peaks ◽  
Scanning Electron

Phase equilibria were studied in the system Ni-Sn-Bi. Special attention has been paid to the identification of the recently found ternary phase. For this purpose samples were synthesized using intimately mixed powders. After annealing and quenching, all alloys were analyzed by scanning electron microscope and by X-ray diffraction. The results give evidences about the existence of a ternary compound with approximate formula Ni6Sn2Bi to Ni7Sn2Bi. Overlapping of some neighboring diffraction peaks of this phase with NiBi and Ni3Sn_LT is the reason for the difficulties related to the X-ray diffraction identification of the ternary phase.

scholarly journals Pengaruh Suhu Kalsinasi terhadap Karakteristik Komposit Forsterit-Karbon Tersintesis dalam Medium Gas Argon

2020 ◽  
Vol 16 (2) ◽  
pp. 12
Author(s):  
Solihudin Solihudin ◽  
Haryono Haryono ◽  
Atiek Rostika Noviyanti ◽  
Muhammad Rizky Ridwansyah
Keyword(s):  
Fourier Transform ◽  
Electron Microscope ◽  
Scanning Electron Microscope ◽  
Rice Husk ◽  
Energy Dispersive Spectroscopy ◽  
Carbon Composite ◽  
X Ray Diffraction ◽  
Argon Gas ◽  
X Ray ◽  
Scanning Electron

<p>Komposit forsterit-karbon merupakan salah satu material modifikasi dari forsterit yang berpotensi memiliki sifat isolator panas baik. Karbon dalam komposit dapat mengisi cacat titik pada kristal forsterit. Arang sekam padi (residu gasifikasi) mengandung SiO2 amorf dan karbon yang tinggi. Penelitian ini bertujuan menentukan pengaruh suhu kalsinasi dalam medium gas inert (dengan pengaliran gas argon) terhadap karakteristik komposit forsterit-karbon dari arang sekam padi dan magnesium karbonat. Metode penelitian meliputi preparasi arang sekam padi hasil gasifikasi, dan sintesis forsterit-karbon. Proses sintesis komposit forsterit karbon dilakukan dengan cara mencampurkan arang sekam padi dengan kalium karbonat pada rasio mol magmesium terhadap silikon sebesar 2 : 1 kemudian dikalsinasi dengan suhu divariasikan (700, 800, 900, dan 1000 oC). Selanjutnya sampel hasil sintesis dikarakterisasi dengan Fourier-transform infrared (FTIR), X-ray diffraction (XRD), dan scanning electron microscope-energy dispersive spectroscopy (SEM-EDS). Hasil karakterisasi dengan FTIR dan XRD diperoleh kesimpulan bahwa forsterit mulai terbentuk pada suhu kalisiasi 800 oC dan sempurna pada suhu 1000 oC, karenanya komposit yang terbentuk pada 1000 oC dimungkinkan sebagai forsterit-karbon, di mana unsur-unsur yang terkandung ditunjukkan oleh SEM-EDS.</p><p> </p><p><strong>The Effect of Calcination Temperature on the Characteristics of Forsterite-Carbon Composites Synthesized in Argon Gas Medium</strong>. Forsterite-carbon composite is one of the material modifications of forsterite, which potentially has a good heat insulation property. Carbon in composites can fill point defects in forsterite crystals. Rice husk charcoal, as gasification residues, contains high amorphous SiO2 and carbon. This study aims to determine the effect of temperature on the calcination of a mixture of rice husk charcoal and magnesium carbonate under an inert gas (argon gas) on the characteristics of the forsterite-carbon composite produced. The experimental research performed includes the preparation of gasified rice husk charcoal and the synthesis of the carbon-forsterite composite. The synthesis process of the carbon-forsterite composites was carried out by mixing rice husk charcoal with potassium carbonate at a mole ratio of magnesium to silicon of 2 : 1. The mixture was then calcined with varying temperatures (700, 800, 900, and 1000 °C). Furthermore, the synthesized sample was characterized by Fourier-transform infrared (FTIR), X-ray diffraction (XRD), and scanning electron microscope-energy dispersive spectroscopy (SEM-EDS). The FTIR and XRD analysis show that the forsterites began to form at a calcination temperature of 800 °C and perfectly formed at a temperature of 1000 °C; therefore, the composite formed at 1000 °C is possible as forsterite-carbon, in which the contained elements were indicated by SEM-EDS.</p>

scholarly journals Peningkatan Kelarutan dan Laju Disolusi Glimepirid Melalui Metode Kokristalisasi

2017 ◽  
Vol 4 (1) ◽  
pp. 35
Author(s):  
Fitrianti Darusman ◽  
Sundani N Soewandhi ◽  
Rachmat Mauludin
Keyword(s):  
Fourier Transform ◽  
Electron Microscope ◽  
Scanning Electron Microscope ◽  
X Ray Diffraction ◽  
X Ray ◽  
Infra Red ◽  
Scanning Electron

Telah dilakukan kokristalisasi glimepirid (GMP) dengan asam oksalat (AO) menggunakan metode penggilingan dan pelarutan (menggunakan pelarut aseton). Diagram fase sistem biner GMP-AO digunakan untuk identifikasi awal pembentukan interaksi antar kedua komponen serta ditegaskan kembali dengan analisis mikroskopik menggunakan alat pemanas (hot stage) yang dihubungkan dengan mikroskop polarisasi. Padatan hasil kokristalisasi dikarakterisasi dengan metode analisis termal (Differential Scanning Calorymetry), difraktometri sinar-X serbuk (Powder X-Ray Diffraction), spektrofotometri inframerah (Fourier Transform-Infra Red) dan mikroskopi (Scanning Electron Microscope). Hasil identifikasi dan karakterisasi menunjukkan interaksi eutektik antara kedua fase kristalin GMP-AO dalam keadaan padat pada perbandingan molar 3:7, dengan titik eutektik pada temperatur 128,7°C. Selanjutnya, uji kelarutan dan laju disolusinya menggunakan media dapar fosfat pH 7,4. Kelarutan dan laju disolusi GMP hasil kokristalisasi meningkat dibandingkan dengan campuran fisika dan senyawa tunggalnya.Kata kunci : glimepirid, kokristalisasi, eutektik, kelarutan dan laju disolusi.

scholarly journals Optimasi Ukuran dan Jumlah Pori yang Terbentuk Pada Molacularly Imprinted Polymer (MIP) Nano Karbaril (C12H11NO2)

POSITRON ◽  
2020 ◽  
Vol 10 (2) ◽  
pp. 14
Author(s):  
Suci Aprilia ◽  
Erry Koryanti ◽  
Idha Royani
Keyword(s):  
Fourier Transform ◽  
Electron Microscope ◽  
Scanning Electron Microscope ◽  
Ethylene Glycol ◽  
Methacrylic Acid ◽  
Molecular Imprinted Polymer ◽  
X Ray Diffraction ◽  
Imprinted Polymer ◽  
X Ray ◽  
Scanning Electron

Telah dilakukan pembuatan molecular imprinted polymer (MIP) nano karbaril dengan metode cooling-heating. Pembuatan MIP nano karbaril bertujuan untuk mendapatkan material sensor yang potensial dalam aplikasinya. Dalam penelitian ini, bahan aktif karbaril di-milling dengan variasi waktu 10 menit dan 15 menit. Pada proses polimerisasi melibatkan templat nano karbaril, methacrylic acid (MAA) sebagai monomer fungsional, ethylene glycol dimathacrylate (EDMA) sebagai crosslinker, benzoil peroksida (BPO) sebagai inisiator, dan acetonitril sebagai pelarut yang disintesis menggunakan metode cooling-heating. Dengan cara yang sama, non-imprinted polymer (NIP) juga dibuat sebagai polimer kontrol.  NIP merupakan polimer yang dibuat dengan komposisi dan cara yang sama dengan MIP, namun tidak ditambahkan nano karbaril sebagai zat aktif. Pembuangan templat pada proses ekstraksi sangat berperan penting untuk menghasilkan material sensor yang baik. MIP, polimer, dan NIP yang dihasilkan di karakterisasi menggunakan Fourier transform infrared (FTIR) dan sampel terbaik dideteksi lebih lanjut dengan uji x-ray diffraction (X-RD), dan scanning electron microscope (SEM). Hasil FTIR menunjukkan bahwa gugus fungsi spesifik nano karbaril pada NIP tidak tampak bila dibandingkan dengan spektra MIP, dan terjadi penurunan persen transmitansi pada polimer dan peningkatan % transmitansi pada MIP. Hal ini menjelaskan bahwa terjadi penurunan konsentrasi nano karbaril pada MIP setelah proses ektraksi. Hasil X-RD menunjukkan ukuran kristal yaitu 9,16 Å. Hasil SEM menunjukkan bahwa jumlah pori tercetak dengan ukuran ≤100 nm yaitu 383 pori.  Data ini mengindikasikan bahwa MIP nano karbaril potensial untuk diaplikasikan sebagai material sensor.

Sign in / Sign up

Export Citation Format

Share Document