scholarly journals Fluid flow in the impulse valve of a hydraulic ram

2020 ◽  
Vol 3 (22) ◽  
Author(s):  
Wojciech Sobieski ◽  
Dariusz Grygo
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Numerical Modeling ◽  
Hydrodynamic Pressure ◽  
Water Velocity ◽  
Experimental Measurements ◽  
Ansys Fluent ◽  
Working Cycle ◽  
Numerical Studies ◽  
Minimum Force

The paper presents the results of a study investigating the equilibrium of forces acting on the closing element of the impulse valve in a water ram at the end of the acceleration stage. Acceleration is one of the three main stages in the working cycle of a water ram. In the first part of the paper, we estimated water velocity based on our earlier experimental measurements. We also calculated the minimum force required for closing the impulse valve. The second part of the paper discusses two variants of a numerical model, which was developed in ANSYS Fluent to determine the result-ant hydrodynamic pressure and, consequently, the forces acting on the head of the impulse valve at the end of the acceleration stage. The main aim of this research was to verify the applicability of numerical modeling in water ram studies. The present study was motivated by the fact that Computational Fluid Dynamics is very rarely applied to water rams. In particular, we have not found any numerical studies related to the equilibrium of forces acting on the closing element of the impulse valve in a water ram.

Tonal Noise Reduction in a Radial Fan With Forward-Curved Blades

2014 ◽  
Author(s):  
Manoochehr Darvish ◽  
Bastian Tietjen ◽  
Daniel Beck ◽  
Stefan Frank
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Aerodynamic Performance ◽  
Computational Aeroacoustics ◽  
Experimental Measurements ◽  
Noise Generation ◽  
Tonal Noise ◽  
Outlet Angle ◽  
And Performance ◽  
Impeller Geometry

The main focus of this work is on the geometrical modifications that can be applied to the fan wheel and the volute tongue of a radial fan to reduce the tonal noise. The experimental measurements are performed by using the in-duct method in accordance with ISO 5136. In addition to the experimental measurements, CFD (Computational Fluid Dynamics) and CAA (Computational Aeroacoustics) simulations are carried out to investigate the effects of different modifications on the noise and performance of the fan. It is shown that by modifying the blade outlet angle, the tonal noise of the fan can be reduced without affecting the performance of the fan. Moreover, it is indicated that increasing the number of blades leads to a significant reduction in the tonal noise and also an improvement in the performance. However, this trend is only valid up to a certain number of blades, and a further increment might reduce the aerodynamic performance of the fan. Besides modifying the impeller geometry, new volute tongues are designed and manufactured. It is demonstrated that the shape of the volute tongue plays an important role in the tonal noise generation of the fan. It is possible to reduce the tonal noise by using stepped tongues which produce phase-shift effects that lead to an effective local cancellation of the noise.

CFD Leakage Predictions of Unworn and Worn Labyrinth Seals With and Without Tooth Axial Offset

2017 ◽  
Author(s):  
Hasham H. Chougule ◽  
Alexander Mirzamoghadam
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Numerical Modeling ◽  
Steady State ◽  
Flow Field ◽  
Labyrinth Seals ◽  
Small Clearance ◽  
Total Leakage ◽  
Computational Fluid Dynamics Cfd ◽  
Flow Deflection

The objective of this study is to develop a Computational Fluid Dynamics (CFD) based methodology for analyzing and predicting leakage of worn or rub-intended labyrinth seals during operation. The simulations include intended tooth axial offset and numerical modeling of the flow field. The purpose is to predict total leakage through the seal when an axial tooth offset is provided after the intended/unintended rub. Results indicate that as expected, the leakage for the in-line worn land case (i.e. tooth under rub) is higher compared to unworn. Furthermore, the intended rotor/teeth forward axial offset/shift with respect to the rubbed land reduces the seal leakage. The overall leakage of a rubbed seal with axial tooth offset is observed to be considerably reduced, and it can become even less than a small clearance seal designed not to rub. The reduced leakage during steady state is due to a targeted smaller running gap because of tooth offset under the intended/worn land groove shape, higher blockages, higher turbulence and flow deflection as compared to worn seal model without axial tooth offset.

Transportation Performance of Highly Concentrated Coal-Water Slurries Prepared from Indian Coals

2014 ◽  
Vol 592-594 ◽  
pp. 869-873 ◽  
Author(s):  
Arunanshu Chakravarthy ◽  
Satish Kumar ◽  
S.K. Mohapatra
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Rheological Behaviour ◽  
Pseudoplastic Fluid ◽  
Ansys Fluent ◽  
Water Slurry ◽  
Solids Concentration ◽  
Coal Water Slurry ◽  
Indian Coals ◽  
Fluid Behaviour

The rheological behaviour of concentrated coal-water slurries prepared from three different Indian coals were investigated using an Anton Paar rheometer. The perspective was laid in to study the effect of solids concentration on the rheological behaviour of coal water slurry. It was observed that coal water slurry exhibited non-Newtonian pseudoplastic fluid behaviour at concentrations above 30 % by weight. The apparent viscosity varied with the amount of coal in the slurry. The rheological data were utilized to predict the pressure drop characteristics of coal water slurry flowing through a 53 mm diameter slurry pipeline using ANSYS Fluent 14.0 computational fluid dynamics code.

Experimental and simulation study of thermal accumulation in an enclosed vehicle

2019 ◽  
Vol 233 (14) ◽  
pp. 3621-3629
Author(s):  
Sing Ngie David Chua ◽  
Boon Kean Chan ◽  
Soh Fong Lim
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Three Dimensional ◽  
Experimental Tests ◽  
Dynamics Simulation ◽  
Computational Fluid Dynamics Simulation ◽  
Heat Accumulation ◽  
Ansys Fluent ◽  
Direct Exposure ◽  
Car Park

Thermal accumulation in a car cabin under direct exposure to sunlight can be extremely critical due to the risk of heatstroke especially to children who are left unattended in the car. There are very limited studies in the literature to understand the thermal behaviour of a car that is parked in an open car park space and the findings are mostly inconsistent among researchers. In this paper, the studies of thermal accumulation in an enclosed vehicle by experimental and computational fluid dynamics simulation approaches were carried out. An effective and economical method to reduce the heat accumulation was proposed. Different test conditions such as fully enclosed, fully enclosed with sunshade on front windshield and different combinations of window gap sizes were experimented and presented. Eight points of measurement were recorded at different locations in the car cabin and the results were used as the boundary conditions for the three-dimensional computational fluid dynamics simulation. The computational fluid dynamics software used was ANSYS FLUENT 16.0. The results showed that the application of sunshade helped to reduce thermal accumulation at car cabin by 11.5%. The optimum combination of windows gap size was found to be with 4-cm gap on all four windows which contributed to a 21.1% reduction in car cabin temperature. The results obtained from the simulations were comparable and in agreement with the experimental tests.

CFD Modelling of Multiphase Flows: An Overview

2003 ◽  
Author(s):  
Rajnish K. Calay ◽  
Arne E. Holdo
Keyword(s):  
Fluid Dynamics ◽  
Mass Transfer ◽  
Computational Fluid Dynamics ◽  
Numerical Modeling ◽  
Mathematical Models ◽  
Cfd Modelling ◽  
Two Phase ◽  
Wide Range ◽  
Computational Fluid Dynamics Cfd ◽  
Numerical Modeling Of Flows

The Computational Fluid Dynamics (CFD) is now increasingly being used for modeling industrial flows, i.e. flows which are multiphase and turbulent. Numerical modeling of flows where momentum, heat and mass transfer occurs at the interface presents various difficulties due to the wide range of mechanisms and flow scenarios present. This paper attempts to provide a summary of available mathematical models and techniques for two-phase flows. Some comments are also made on the models available in the commercially available codes.

Computational Fluid Dynamics Modelling of a Load Sensing Proportional Valve

2019 ◽  
Author(s):  
Alessandro Corvaglia ◽  
Giorgio Altare ◽  
Roberto Finesso ◽  
Massimo Rundo
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Steady State ◽  
Complex Geometry ◽  
Ansys Fluent ◽  
Proportional Valve ◽  
Fluid Forces ◽  
Load Sensing ◽  
Cfd Models ◽  
Dynamics Modelling

Abstract In this paper, two 3D CFD models of a load sensing proportional valve are contrasted. The models were developed with two different software, Simerics PumpLinx® and ANSYS Fluent®. In both cases the mesh was dynamically modified based on the fluid forces acting on the local compensator. In the former, a specific template for valves was used, in the latter a user-defined function was implemented. The models were validated in terms of flow rate and pressure drop for different positions of the main spool by means of specific tests. Two configurations were tested: with the local compensator blocked and free to regulate. The study has brought to evidence the reliability of the CFD models in evaluating the steady-state characteristics of valves with complex geometry.

High Swept-Back Delta Wing Flow

2014 ◽  
Vol 1016 ◽  
pp. 377-382 ◽  
Author(s):  
Thi Kim Dung Hoang ◽  
Phu Khanh Nguyen ◽  
Yoshiaki Nakamura
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Lift Force ◽  
Delta Wing ◽  
Air Velocity ◽  
Rolling Angle ◽  
Ansys Fluent ◽  
Absolute Value ◽  
Numerical Tests ◽  
Low Speed Wind Tunnel

In this study, an experimentally and numerically investigation was carried out to obtain characteristics (lift force, drag force ...) on 74.5 degree Delta wing. The experiment tests were conducted at Hanoi University of Science and Technology low-speed wind tunnel facility, whereas the numerical tests were performed using the commercial computational fluid dynamics software ANSYS/FLUENT. The apparition of the vortices upon the Delta wing caused the negative pressure distribution on the wing which reached a maximum absolute value at the vortex core. The characteristics of high swept-back Delta wing were investigated at air velocity of 10 m/s and attack angle of 20 degree in changing the rolling angle of the wing from 0 to 20 degree.

Sign in / Sign up

Export Citation Format

Share Document