scholarly journals CHEMICAL ETCHING AND HARDNESS ANISOTROPY IN LLYSINE MONOHYDROCHLORIDE DIHYDRATE CRYSTAL

2021 ◽  
Vol 14 (03) ◽  
pp. 1892-1898
Author(s):  
P. V. Raja Shekar ◽  
D. Madhavi Latha ◽  
Ch. Sateesh Chandra ◽  
K. Kishan Rao
Author(s):  
M.E. Lee

The crystalline perfection of bulk CdTe substrates plays an important role in their use in infrared device technology. The application of chemical etchants to determine crystal polarity or the density and distribution of crystallographic defects in (100) CdTe is not well understood. The lack of data on (100) CdTe surfaces is a result of the apparent difficulty in growing (100) CdTe single crystal substrates which is caused by a high incidence of twinning. Many etchants have been reported to predict polarity on one or both (111) CdTe planes but are considered to be unsuitable as defect etchants. An etchant reported recently has been considered to be a true defect etchant for CdTe, MCT and CdZnTe substrates. This etchant has been reported to reveal crystalline defects such as dislocations, grain boundaries and inclusions in (110) and (111) CdTe. In this study the effect of this new etchant on (100) CdTe surfaces is investigated.The single crystals used in this study were (100) CdTe as-cut slices (1mm thickness) from Bridgman-grown ingots.


2018 ◽  
Author(s):  
Julia Sun ◽  
Benjamin Almquist

For decades, fabrication of semiconductor devices has utilized well-established etching techniques to create complex nanostructures in silicon. Of these, two of the most common are reactive ion etching in the gaseous phase and metal-assisted chemical etching (MACE) in the liquid phase. Though these two methods are highly established and characterized, there is a surprising scarcity of reports exploring the ability of metallic films to catalytically enhance the etching of silicon in dry plasmas via a MACE-like mechanism. Here, we discuss a <u>m</u>etal-<u>a</u>ssisted <u>p</u>lasma <u>e</u>tch (MAPE) performed using patterned gold films to catalyze the etching of silicon in an SF<sub>6</sub>/O<sub>2</sub> mixed plasma, selectively increasing the rate of etching by over 1000%. The degree of enhancement as a function of Au catalyst configuration and relative oxygen feed concentration is characterized, along with the catalytic activities of other common MACE metals including Ag, Pt, and Cu. Finally, methods of controlling the etch process are briefly explored to demonstrate the potential for use as a liquid-free fabrication strategy.


Author(s):  
Jianwei Zhou ◽  
Wei Zheng ◽  
Taekoo Lee

Abstract Multi-Chip Package (MCP) decapsulation is now becoming a rising problem. Because for traditional decapsulation method, acid can’t dissolve the top silicon die to expose the bottom die surface in MCP. It makes inspecting the bottom die in MCP is difficult. In this paper, a new MCP decapsulation technology combining mechanical polishing with chemical etching is introduced. This new technology can remove the top die quickly without damaging the bottom die using KOH and Tetra-Methyl Ammonium Hydroxide (TMAH). The technology process and relative application are presented. The factors that affect the KOH and TMAH etch rate are studied. The usage difference between the two etchant is discussed.


2018 ◽  
Author(s):  
Ong Pei Hoon ◽  
Ng Kiong Kay ◽  
Gwee Hoon Yen

Abstract Chemical etching is commonly used in exposing the die surface from die front-side and die backside because of its quick etching time, burr-free and stress-free. However, this technique is risky when performing copper lead frame etching during backside preparation on small and non-exposed die paddle package. The drawback of this technique is that the copper leads will be over etched by 65% Acid Nitric Fuming even though the device’s leads are protected by chemical resistance tape. Consequently, the device is not able to proceed to any other further electrical measurements. Therefore, we introduced mechanical preparation as an alternative solution to replace the existing procedure. With the new method, we are able to ensure the copper leads are intact for the electrical measurements to improve the effectiveness and accuracy of physical failure analysis.


Author(s):  
Dongmei Meng ◽  
Joe Rupley ◽  
Chris McMahon

Abstract This paper presents decapsulation solutions for devices bonded with Cu wire. By removing mold compound to a thin layer using a laser ablation tool, Cu wire bonded packages are decapsulated using wet chemical etching by controlling the etch time and temperature. Further, the paper investigates the possibilities of decapsulating Cu wire bonded devices using full wet chemical etches without the facilitation of laser ablation removing much of mold compound. Additional discussion on reliability concerns when evaluating Cu wirebond devices is addressed here. The lack of understanding of the reliability of Cu wire bonded packages creates a challenge to the FA engineer as they must develop techniques to help understanding the reliability issue associated with Cu wire bonding devices. More research and analysis are ongoing to develop appropriate analysis methods and techniques to support the Cu wire bonding device technology in the lab.


2013 ◽  
Vol 28 (11) ◽  
pp. 1207-1212 ◽  
Author(s):  
Jian-Wen LI ◽  
Ai-Jun ZHOU ◽  
Xing-Quan LIU ◽  
Jing-Ze LI

Small ◽  
2020 ◽  
Vol 16 (51) ◽  
pp. 2007045
Author(s):  
Mei Sun ◽  
Bocheng Yu ◽  
Mengyu Hong ◽  
Zhiwei Li ◽  
Fengjiao Lyu ◽  
...  

Sign in / Sign up

Export Citation Format

Share Document