scholarly journals An experimental study on the shear capacity of corroded reinforced concrete beams without shear reinforcement

2021 ◽  
Vol 15 (1) ◽  
pp. 55-66
Author(s):  
Nguyen Ngoc Tan ◽  
Nguyen Trung Kien
Keyword(s):  
Shear Strength ◽  
Reinforced Concrete ◽  
Concrete Beam ◽  
Reinforced Concrete Beam ◽  
Shear Capacity ◽  
Reinforced Concrete Beams ◽  
Rc Beams ◽  
Accelerated Corrosion ◽  
Steel Rebar ◽  
Accelerated Corrosion Test

The effect of corrosion on the structural behavior of reinforced concrete (RC) beams without stirrups was experimentally investigated. A total of eight medium-scale RC beams were constructed without stirrups. The beams were 150 mm in width, 200 mm in depth, and 1100 mm in length. Test variables included three distinct degrees of corrosion (0%, 3.13%, 4.11%, and 4.93% by mass loss of steel rebar). Six beams were subjected to an accelerated corrosion test, while two beams served as non-corroded control beams. All beams were tested under four-point loading failure after the corrosion stage. The effect of various small degrees of corroded longitudinal reinforcements has been observed for the shear capacity. Test findings found that all tested beams had a brittle failure with tested corrosion degrees. Moreover, corroded beams that are exposed to 3% and 4% average corrosion degree reported having a larger shear capacity of approximately 7% compared to control beams. Lastly, beams with a corrosion degree of about 5% showed a decrease of 10% shear strength and a different failure mechanism with distinguished cracking patterns due to the formation of corrosion cracks along the longitudinal reinforcements. Keywords: reinforced concrete beam; reinforcement corrosion; shear strength; no stirrups.

scholarly journals Limit Equilibrium Method-based Shear Strength Prediction for Corroded Reinforced Concrete Beam with Inclined Bars

Materials ◽  
2019 ◽  
Vol 12 (7) ◽  
pp. 1014 ◽  
Author(s):  
Yafei Ma ◽  
Baoyong Lu ◽  
Zhongzhao Guo ◽  
Lei Wang ◽  
Hailong Chen ◽  
...  
Keyword(s):  
Shear Strength ◽  
Reinforced Concrete ◽  
Concrete Beam ◽  
Limit Equilibrium ◽  
Reinforced Concrete Beam ◽  
Limit Equilibrium Method ◽  
Shear Capacity ◽  
Reinforced Concrete Beams ◽  
Equilibrium Method ◽  
Diagonal Crack

Shear strength is a widely investigated parameter for reinforced concrete structures. The corrosion of reinforcement results in shear strength reduction. Corrosion has become one of the main deterioration factors in reinforced concrete beam. This paper proposes a shear strength model for beams with inclined bars based on a limit equilibrium method. The proposed model can be applied to both corroded and uncorroded reinforced concrete beams. Besides the tensile strength of longitudinal steel bars, the shear capacity provided by the concrete on the top of the diagonal crack, the tensile force of the shear steel at the diagonal crack, the degradation of the cross-sectional area and strength of the reinforcements induced by corrosion are all considered. An experimental work on two groups accelerated corroded beams was performed. Good agreements were found between the proposed theoretical predictions and experimental observations.

Predicting the effect of stirrups on shear strength of reinforced normal-strength concrete (NSC) and high-strength concrete (HSC) slender beams using artificial intelligence

2006 ◽  
Vol 33 (8) ◽  
pp. 933-944 ◽  
Author(s):  
H El Chabib ◽  
M Nehdi ◽  
A Saïd
Keyword(s):  
Shear Strength ◽  
Reinforced Concrete ◽  
High Strength ◽  
Shear Capacity ◽  
Reinforced Concrete Beams ◽  
Design Parameters ◽  
Rc Beams ◽  
Shear Reinforcement ◽  
Strength Concrete ◽  
Shear Design

The exact effect that each of the basic shear design parameters exerts on the shear capacity of reinforced concrete (RC) beams without shear reinforcement (Vc) is still unclear. Previous research on this subject often yielded contradictory results, especially for reinforced high-strength concrete (HSC) beams. Furthermore, by simply adding Vc and the contribution of stirrups Vs to calculate the ultimate shear capacity Vu, current shear design practice assumes that the addition of stirrups does not alter the effect of shear design parameters on Vc. This paper investigates the validity of such a practice. Data on 656 reinforced concrete beams were used to train an artificial neural network model to predict the shear capacity of reinforced concrete beams and evaluate the performance of several existing shear strength calculation procedures. A parametric study revealed that the effect of shear reinforcement on the shear strength of RC beams decreases at a higher reinforcement ratio. It was also observed that the concrete contribution to shear resistance, Vc, in RC beams with shear reinforcement is noticeably larger than that in beams without shear reinforcement, and therefore most current shear design procedures provide conservative predictions for the shear strength of RC beams with shear reinforcement.Key words: analysis, artificial intelligence, beam depth, compressive strength, modeling, shear span, shear strength.

Experimental Research on Crazing-Resistance of Inclined Section of Basalt Fiber Reinforced Concrete Beams

2014 ◽  
Vol 584-586 ◽  
pp. 899-903
Author(s):  
Wei Chen ◽  
Xiang Peng Li ◽  
Ting Ting Chen ◽  
Xiao Yang Wang ◽  
Chao Chao Ma
Keyword(s):  
Reinforced Concrete ◽  
Concrete Beam ◽  
Concrete Beams ◽  
Basalt Fiber ◽  
Volume Ratio ◽  
Reinforced Concrete Beam ◽  
Shear Capacity ◽  
Fiber Reinforced Concrete ◽  
Reinforced Concrete Beams ◽  
Fiber Reinforced

In order to research the influence of the shear capacity of reinforced concrete beam with the incorporation of basalt fiber, four basalt fiber reinforced concrete beams with parameters of length and volume ratio were designed and made. The fiber lengths were 12mm and 30mm, and the volume ratios were 1‰ and 2‰. The test data of basalt fiber reinforced concrete was obtained through the shear experiments and comparison with the common reinforced concrete beam. The results of the experiment show that the cracking load of the basalt fiber reinforced concrete beam increase obviously with the growing of fiber characteristic parameters, and effectively reduce the diagonal crack width.

Calculation of Shear Capacity of Steel Reinforced Concrete Beams Strengthened with Near-Surface Mounted CFRP Rods

2012 ◽  
Vol 193-194 ◽  
pp. 852-854
Author(s):  
Wei Hua Chen ◽  
Mei Qin Wu
Keyword(s):  
Reinforced Concrete ◽  
Reinforced Concrete Beam ◽  
Shear Capacity ◽  
Reinforced Concrete Beams ◽  
Rc Beams ◽  
Near Surface ◽  
Steel Reinforced Concrete ◽  
Carbon Fiber Reinforce Polymer ◽  
Near Surface Mounted ◽  
Fiber Reinforce

Some calculated methods of shear capacity of RC beams strengthened with NSM(near-surface mounted) CFRP(Carbon fiber reinforce polymer) rods are reviewed based on the experimental data on shear capacity of RC beams strengthened with NSM CFRP rods. Therefore, according to the destruction forms of steel reinforced concrete beam strengthened with NSM CFRP rods, the formula for calculating the shear capacity of the beam is given. The formula is expressed clearly, simple and easy to use.

scholarly journals Influence of coarse aggregate on the shear strength of reinforced concrete beams

2020 ◽  
Author(s):  
◽  
Hoosen Ahmed Jajbhay
Keyword(s):  
Shear Strength ◽  
Reinforced Concrete ◽  
Concrete Beam ◽  
Coarse Aggregate ◽  
Concrete Beams ◽  
Shear Capacity ◽  
Reinforced Concrete Beams ◽  
Shear Reinforcement ◽  
Shear Transfer ◽  
Coarse Aggregates

Research to accurately predict the shear capacity of reinforced concrete beams without shear reinforcement has been ongoing since the early 20th century. Aggregate interlock of the coarse aggregates at the shear crack interface is one of the internal mechanisms of shear transfer and a major contributor to the shear capacity of slender beams. It is plausible, therefore, to investigate if the coarse aggregate itself influences the shear capacity of a concrete beam. The influence of the type of coarse aggregate on the shear capacity of beams without shear reinforcement was investigated in this study. From the literature study an understanding of the properties of coarse aggregates was gained, the internal mechanisms of shear transfer in reinforced concrete beams without shear reinforcement were determined, and the parameters influencing shear strength were identified. Based on this information an experimental program was designed. Eighteen reinforced concrete beams without shear reinforcement were cast. The beams were cast from three different types of coarse aggregates commonly used in the Durban area, i.e., dolerite, quartzite and tillite. For each type of coarse aggregate two variations were tested, i.e., 13 mm and 19 mm maximum aggregate sizes. For each size of coarse aggregate, three concrete strengths were tested. The beams were loaded in a beam press, by applying an increasing point load offset from midspan to induce cracking on the shorter side, until shear failure of the beam occurred. For the three concrete strengths, beams cast from dolerite had the highest shear capacity while beams cast from tillite had less shear capacity than beams cast from quartzite coarse aggregate. Furthermore, beams cast from 13 mm maximum size coarse aggregate had higher shear capacity than beams cast from 19 mm aggregate. The conclusion may be drawn that the type and size of coarse aggregate does influence the shear strength of a reinforced concrete beam without shear reinforcement.

Finite Element Analysis of Reinforced Concrete Beams with Transversely Prestressed Bars

2011 ◽  
Vol 368-373 ◽  
pp. 108-113
Author(s):  
Can Liu ◽  
Bo Wu ◽  
Kai Yan Xu
Keyword(s):  
Finite Element ◽  
Reinforced Concrete ◽  
Prestressed Concrete ◽  
Concrete Beam ◽  
Concrete Beams ◽  
Shear Crack ◽  
Reinforced Concrete Beam ◽  
Shear Capacity ◽  
Reinforced Concrete Beams ◽  
Failure Loads

This paper presents a method that using inner transverse prestressing bars to enhance the shear capacity of concrete beams, which can be used in new transformer beams to decrease the sectional dimensions. Four transversely prestressed concrete beams and one ordinary reinforced concrete beam were tested. The nonlinear finite element method was applied to analyze them, and the following conclusions can be drawn: (a) The transverse prestressing bars can efficiently increase the shear capacity and failure load of the reinforced concrete beam, the improvement effect is more obvious when exerting the prestressing force on them properly. (b) On the whole, the simulated load-deflection relationships and failure loads of the five specimens agree well with the corresponding tested load-deflection relationships and failure loads. It indicated that the FE models used in this paper predict the structural behavior of the transversely prestressed concrete beams satisfactorily. (c) From the contour of first principal stress, it can be seen that the transverse prestressing bars can efficiently enhance the shear crack resistance of the reinforced concrete beams, if the area of transversely prestressing bars is almost same, the transverse bars with smaller diameter and smaller spacing will be better. It agrees well with the test results.

scholarly journals Stiffness and Strength Analysis of Flexural RC beams strengthened with CFRP Sheets Considering the Influence of Pre-cracking

Mechanika ◽  
2020 ◽  
Vol 26 (4) ◽  
pp. 277-284
Author(s):  
Tadas LISAUSKAS ◽  
Mindaugas AUGONIS ◽  
Tadas ZINGAILA ◽  
Mario Rui Tiago ARRUDA
Keyword(s):  
Reinforced Concrete ◽  
Concrete Beam ◽  
Reinforced Concrete Beam ◽  
Reinforced Concrete Beams ◽  
Bending Test ◽  
Experimental Program ◽  
Strength Analysis ◽  
Rc Beams ◽  
Cfrp Sheets ◽  
Good Agreement

                           This paper presents experimental, numerical and analytical analysis of newly cast and pre-cracking flexural reinforced concrete beams strengthened with CFRP. In total, 9 intermediate-scale composite beams were cast and tested using 4-point bending test setup. Midspan deflection, width of the cracks, concrete and CFRP strains were measured during the experimental program. Clear efficiency of composite pre-cracked beams was observed in comparison to newly cast beams: enhanced flexural capacity and increased stiffness after appearance of primary cracks in tension zone. Good agreement was found comparing experimental and theoretical (EC2) deflections of RC beams strengthened with CFRP. However, for more detailed verification, the analysis should be extended with more specimens. The shear stress at the end of CFRP sheets between the concrete and CFRP increased rapidly until reaching maximum slip value, when the reinforced concrete beam strengthened with CFRP reaches 60-90 % utilization of load bearing capacity. All experimental results were compared with numerical and analytical calculations. Experimental, numerical and analytical results were in sufficiently good agreement.

Experimental Study on Shear of Reinforced Concrete Beams with High Strength Rebars as Stirrups under Different Shear Span Ratios

2014 ◽  
Vol 578-579 ◽  
pp. 164-167 ◽  
Author(s):  
Peng Li ◽  
Xian Tang Zhang ◽  
Ming Ping Wang
Keyword(s):  
Reinforced Concrete ◽  
Concrete Beam ◽  
Concrete Beams ◽  
High Strength ◽  
Reinforced Concrete Beam ◽  
Shear Behavior ◽  
Shear Capacity ◽  
Reinforced Concrete Beams ◽  
Test Results ◽  
Shear Span

To investigate the influence of shear span ratio for the shear behavior of reinforced concrete beam with HRBF500 high strength rebars as stirrups, an experiment was carried out, which included 8 simply supported beams with HRBF500 rebars as stirrups. Under concentrated loads, the crack, deflection, strain of rebars, bearing capacity and failure mode are observed under different shear span ratios. Some comparisons are made between test results and calculated outcome. It shows that the shear span ratio has very important influent on the shear behavior of reinforced concrete beam with HRBF500 high strength bars as stirrups. Formula in code for design of concrete structures can be used to calculate its shear capacity with enough safety.

scholarly journals Influence of Steel Fiber on the Shear Strength of a Concrete Beam

2018 ◽  
Vol 4 (7) ◽  
pp. 1501 ◽  
Author(s):  
Ali Ammar Hameed ◽  
Mohannad Husain Al-Sherrawi
Keyword(s):  
Shear Strength ◽  
Reinforced Concrete ◽  
Concrete Beam ◽  
Shear Failure ◽  
Steel Fiber ◽  
Concrete Beams ◽  
Shear Capacity ◽  
Steel Fibers ◽  
Reinforced Concrete Beams ◽  
Shear Reinforcement

The shear failure in a concrete beam is a brittle type of failure. The addition of steel fibers in a plain concrete mix helps to bridge and restrict the cracks formed in the brittle concrete under applied loads, and enhances the ductility of the concrete. In this research an attempt was made to investigate the behavior and the ultimate shear strength of hooked end steel fiber reinforced concrete beams without traditional shear reinforcement. Four simply-supported reinforced concrete beams with a shear span-to-depth ratio of about 3.0 were tested under two-point loading up to failure. Steel fibers volumetric fractions that used were 0.0, 0.5, 0.75 and 1.0%. Test results indicated that using 1.0% volume fraction of hooked steel fiber led to exclude shear failure and enhanced the use of steel fibers as shear reinforcement in concrete beams. The results also showed that a concrete beam with hooked steel fiber provided higher post-flexural-cracking stiffness, an increase in the shear capacity and energy absorption and an increase in the maximum concrete and steel reinforcement strains.

Experimental Study on Fatigue Performance of the Reinforced Concrete Beam with Stainless Steel Rebar

2014 ◽  
Vol 584-586 ◽  
pp. 1293-1298
Author(s):  
Guo Xue Zhang ◽  
Jia Wei Huang ◽  
Zi Qing Chen ◽  
Xi Wu Zhou
Keyword(s):  
Stainless Steel ◽  
Reinforced Concrete ◽  
Fatigue Life ◽  
Concrete Beam ◽  
Reinforced Concrete Beam ◽  
Reinforced Concrete Beams ◽  
Test Results ◽  
Steel Reinforced Concrete ◽  
Steel Rebar ◽  
Stress States

Based on the fatigue test of 6 stainless steel reinforced concrete beams, number of stress cycles, dropping-coefficient of stiffness and crack width are studied. This paper mainly discussed, under different stress states and reinforcement ratio, the influence of the reinforced concrete beam with stainless steel rebar on crack development, deflection and fatigue life. It can be concluded that, the fatigue life of the stainless steel reinforced concrete beam will go up as the stress decreases. Based on the analysis of the test results, the S-N curve can be deduced.

Sign in / Sign up

Export Citation Format

Share Document