scholarly journals Thermal and Mechanical properties of epoxy-jute fiber composite

2014 ◽  
Vol 27 (2) ◽  
pp. 77-82 ◽  
Author(s):  
H Ahmad ◽  
MA Islam ◽  
MF Uddin
Keyword(s):  
Mechanical Properties ◽  
Thermal Conductivity ◽  
Tensile Strength ◽  
Fiber Length ◽  
Epoxy Composite ◽  
Fiber Composite ◽  
Young Modulus ◽  
Fiber Content ◽  
Jute Fiber ◽  
Elongation At Break

Chopped jute fiber-epoxy composites with varying fiber length (2-12 mm) and mass fraction (0.05-0.35) had been prepared by a heat press unit. The cross-linked product was characterized in terms of specific gravity, thermal conductivity, tensile strength, Young modulus and elongation at break. The transverse thermal conductivities for randomly oriented fibers in the composite were investigated by Lees and Charlton’s method. The tensile strength, Young modulus and elongation at break were investigated by a Universal Tensile Tester. With an increase in the fiber content (irrespective of the fiber length), the thermal conductivity of the composite decreases; the decreasing rate being highest for the fiber length of 2 mm followed by that for the fiber length of 6 and 12 mm. The decreasing rate of the thermal conductivity of the jute-epoxy composite is comparatively higher to that reported in literature for acrylic polymer hemp fiber composite. The tensile strength also decreases with the increase of the fiber content in the composite. The fiber length does not show to have significant effect on the tensile strength of the composite; the variation in strength being masked within experimental error. The Young modulus increases with the increase of fiber content within elastic limit; showing the highest values for the fiber length of 6 mm followed by those for the fiber length of 2 mm and 12 mm. The elongation at break shows slightly increasing trend up to 15% fiber content, but beyond that it decreases drastically. The specific gravity decreases with the increase in the fiber content and thus the recalculated specific tensile strength is found to keep at a stable level of 36MPa up to the fiber content of 20%, and beyond that the specific tensile strength decreases with the increase in the fiber content. It is concluded that jute fiber-epoxy composite could be used as a good heat-insulating material. Further investigation is recommended on the improvement of the thermal insulation keeping the mechanical properties unchanged or even improved. The TGA study is also required to ascertain the field of application of the material. DOI: http://dx.doi.org/10.3329/jce.v27i2.17807 Journal of Chemical Engineering, IEB Vol. ChE. 27, No. 2, December 2012: 77-82

Experimental study on effect of fiber length and fiber content on tensile and flexural properties of bamboo fiber/epoxy composite

2019 ◽  
Vol 15 (5) ◽  
pp. 947-957 ◽  
Author(s):  
Giridharan R. ◽  
Raatan V.S. ◽  
Jenarthanan M.P.
Keyword(s):  
Mechanical Properties ◽  
Fiber Length ◽  
Epoxy Composite ◽  
Natural Fibers ◽  
Weight Ratio ◽  
Fiber Content ◽  
Bamboo Fiber ◽  
Flexural Properties ◽  
Fiber Reinforced ◽  
Content Type

Purpose The purpose of this paper is to study the effects of fiber length and content on properties of E-glass and bamboo fiber reinforced epoxy resin matrices. Experiments are carried out as per ASTM standards to find the mechanical properties. Further, fractured surface of the specimen is subjected to morphological study. Design/methodology/approach Composite samples were prepared according to ASTM standards and were subjected to tensile and flexural loads. The fractured surfaces of the specimens were examined directly under scanning electron microscope. Findings From the experiment, it was found that the main factors that influence the properties of composite are fiber length and content. The optimum fiber length and weight ratio are 15 mm and 16 percent, respectively, for bamboo fiber/epoxy composite. Hence, the prediction of optimum fiber length and content becomes important, so that composite can be prepared with best mechanical properties. The investigation revealed the suitability of bamboo fiber as an effective reinforcement in epoxy matrix. Practical implications As bamboo fibers are biodegradable, recyclable, light weight and so on, their applications are numerous. They are widely used in automotive components, aerospace parts, sporting goods and building industry. With this scenario, the obtained result of bamboo fiber reinforced composites is not ignorable and could be of potential use, since it leads to harnessing of available natural fibers and their composites rather than synthetic fibers. Originality/value This work enlists the effect of fiber length and fiber content on tensile and flexural properties of bamboo fiber/epoxy composite, which has not been attempted so far.

scholarly journals Research Regarding the Mechanical Properties of Some Biodegradable Polymeric Composites for Food Packaging Products

2018 ◽  
Vol 55 (4) ◽  
pp. 498-501
Author(s):  
Constantin Gheorghe Opran ◽  
Elena Grosu ◽  
Marius Enachescu
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Injection Molding ◽  
Biodegradable Polymers ◽  
Food Packaging ◽  
Young Modulus ◽  
Important Application ◽  
Elongation At Break ◽  
Amorphous Character ◽  
Sem Analyses

Biodegradable polymers became one of the most important materials with large applicability, as they do not generate wastes after life cycle. An important application is food packaging fabricated by injection molding processing. In this paper, we present the investigation of the mechanical properties of some biodegradable polymers based on PLA composites obtained by melting processing and their morphology studied by SEM analyses, in comparison to polypropylene and neat PLA. We found out that tensile strength, elongation at break and Young modulus exhibit values appropriate to injection molding processing and they are very close related to crystalline or amorphous character of the materials.

scholarly journals Mechanical Properties and Tensile Fatigue of Graphene Nanoplatelets Reinforced Polymer Nanocomposites

2013 ◽  
Vol 2013 ◽  
pp. 1-9 ◽  
Author(s):  
Ming-Yuan Shen ◽  
Tung-Yu Chang ◽  
Tsung-Han Hsieh ◽  
Yi-Luen Li ◽  
Chin-Lung Chiang ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Fatigue Life ◽  
Carbon Fiber ◽  
Ultimate Tensile Strength ◽  
Composite Laminates ◽  
Epoxy Composite ◽  
Fiber Composite ◽  
Graphene Nanoplatelets ◽  
Carbon Fiber Composite

Graphene nanoplatelets (GNPs) are novel nanofillers possessing attractive characteristics, including robust compatibility with most polymers, high absolute strength, and cost effectiveness. In this study, GNPs were used to reinforce epoxy composite and epoxy/carbon fiber composite laminates to enhance their mechanical properties. The mechanical properties of GNPs/epoxy nanocomposite, such as ultimate tensile strength and flexure properties, were investigated. The fatigue life of epoxy/carbon fiber composite laminate with GPs-added 0.25 wt% was increased over that of neat laminates at all levels of cyclic stress. Consequently, significant improvement in the mechanical properties of ultimate tensile strength, flexure, and fatigue life was attained for these epoxy resin composites and carbon fiber-reinforced epoxy composite laminates.

Effect of Reprocessing Palm Fiber Composite on the Mechanical Properties

2014 ◽  
Vol 699 ◽  
pp. 146-150 ◽  
Author(s):  
Sivakumar Dhar Malingam ◽  
Muhammad Hilmi Ruzaini bin Hashim ◽  
Md Radzai bin Said ◽  
Ahmad Rivai ◽  
Mohd Ahadlin bin Daud ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Flexural Strength ◽  
Waste Disposal ◽  
Oil Palm ◽  
Fiber Composite ◽  
Young Modulus ◽  
Palm Fiber ◽  
Polypropylene Composites ◽  
Useful Life

Concern for the environment, both in terms of limiting the use of finite resources and the need to manage waste disposal, has led to increasing pressure to recycle materials at the end of their useful life. This work describes the effects of reprocessing on the mechanical properties of oil palm fiber reinforced polypropylene composites (PFC). Composites, containing 30wt% fiber with 3wt% Maleate Polypropylene as a coupling agent, were reprocessed up to six times. For this composite, tensile strength (TS) and Young modulus (YM) were found to decrease by 9.6% and 4.7% after being reprocessed for six times. Flexural strength was found to decrease by 23.8% with increased number of reprocessing. The hardness numbers of the composite were found to increase by 7.43% from 72.10 to 77.89 after the sixth reprocessing. In general the degradation on the mechanical properties is considered to be small and PFC has potential to be reprocessed.

scholarly journals Development of Electrically Conductive Nanocrystalline Thin Film for Optoelectronic Applications

2013 ◽  
Vol 15 ◽  
pp. 90-101 ◽  
Author(s):  
Sujan Kumar Das ◽  
Jahid M.M. Islam ◽  
Monirul Hasan ◽  
Humayun Kabir ◽  
Md Abdul Gafur ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Electrical Properties ◽  
Composite Films ◽  
Young Modulus ◽  
Electrically Conductive ◽  
Elongation At Break ◽  
Ohmic Behavior ◽  
Nanocrystalline Thin Film ◽  
Electrically Conductive Composite

Sodium alginate (TiO2) sand composites were prepared by solution casting. Purified sand was added in the composite films to increase electrical conductivity. Electrical properties such as conductivity, capacitance, dielectric constant, and loss tangent of the composites were investigated. The current voltage characteristics for all the composites showed ohmic behavior. All the electrical properties have been found to improve with the incorporation of sand (SiO2) but 6% sand containing composite exhibits the best electrical properties. The mechanical properties tensile strength (TS), elongation at break (Eb) and Young modulus for 6% sand containing composite film are found to be 4.445 MPa, 9.76%, and 72.8 MPa respectively. The experimental results reveal that the blended films exhibit higher stability and improved mechanical properties of both tensile strength and elongation at break in dry state. Water absorption properties of the composites are found to decrease with the increase of sand content. Lowest water uptake properties and highest stability were demonstrated by 6% sand containing sample. Electrically conductive composite films have useful applications for solar cells and optoelectronics. Thus, this study is very much expected to aid in the design and selection of proper composite for the potential application of solar cell and optoelectronics.

Properties of Mortars Mixed with Polystyrene and Hemp Fiber Wastes

2021 ◽  
Author(s):  
Apised Suwansaard
Keyword(s):  
Mechanical Properties ◽  
Thermal Conductivity ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Water Absorption ◽  
Fiber Content ◽  
Partial Replacement ◽  
Hemp Fiber ◽  
Line Crack ◽  
Better Than

When polystyrene (PS) and hemp fiber waste were mixed into the sand aggregate, some physical-mechanical properties of mortar changed. The PS and hemp fiber were tested as partial replacements for sand in mortar with three designated percentages of 2.5, 5.0 and 10.0% by mass. The properties of mortar with PS were found to be better than that of the mortar with hemp fiber. The water absorption of mortar with PS was comparable with the reference mortar but lower than that of mortar with hemp fiber. The compressive strength of the mortar with PS was higher than that with hemp fiber whereas the tensile strength of the mortar with 2.5% PS and hemp fiber was comparable and was higher than that of the reference mortar. The thermal conductivity of a wall plastered by mortar containing PS decreased as the PS content was increased, whereas the thermal conductivity of a wall plastered by mortar containing hemp fiber increased as the hemp fiber content was increased. Thick crack was detected in the reference wall while hair line crack occurred from the wall plastered with PS and hemp fiber mortars. The results indicated that 10.0% PS could be used as a partial replacement for sand in mortar with an improvement in some of the properties of the mortar.

Experimental Study on Property of Rubber Composites Filled With Carbon Nanotubes

2009 ◽  
Vol 87-88 ◽  
pp. 110-115 ◽  
Author(s):  
Ze Peng Wang
Keyword(s):  
Mechanical Properties ◽  
Thermal Conductivity ◽  
Carbon Nanotubes ◽  
Experimental Study ◽  
Tensile Strength ◽  
Dynamic Mechanical Properties ◽  
Rubber Composites ◽  
Elongation At Break ◽  
Tear Strength ◽  
Dynamic Mechanical

The basic and dynamic mechanical properties and thrermal conductivity of rubber composites filled with carbon nanotubes (CNTs) and various particle-sized carbon blacks (CB) were investigated. Results indicated that tear strength and modulus at a definite elongation of rubber composites filled with CNTs were enhanced compared to the conventional CB filler. However, tensile strength and elongation at break became lower. Thermal conductivity of rubber composites partly filled with CNTs is higher than those filled with CB. Rubber filled with the combination of CNTs and the bigger CB particles was beneficial to improve wet-resistant performance and roll resistance of elastomer such as tire.

scholarly journals The Effect of Fiber Length on Tensile Properties of Polyester Resin Composites Reinforced by the Fibers of Sansevieria trifasciata

2014 ◽  
Vol 8 ◽  
pp. 7-13 ◽  
Author(s):  
Palla Hari Sankar ◽  
Y.V. Mohana Reddy ◽  
K. Hemachandra Reddy ◽  
M. Ashok Kumar ◽  
A. Ramesh
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Tensile Properties ◽  
Tensile Testing ◽  
Fiber Length ◽  
Polyester Resin ◽  
Resin Composites ◽  
Elongation At Break ◽  
Polyester Composites ◽  
Scanning Electron

This paper presents the study of the tensile properties of Sansevieria trifasciata – fiber (here after called STF) reinforced polyester composites. The composite sample was fabricated with five different fiber lengths of STF (2, 4, 6, 8 and 10 mm). The fabrication was made by hand lay-up technique. Mechanical properties were determined using tensile testing. An interact between fiber and matrix was observed from the SEM (scanning electron microscope) micrographs. The study reveals that the tensile strength increased with fiber length without effecting the elongation at break of the composite.

Study of the insulation and mechanical properties of hair-reinforced epoxy

2021 ◽  
pp. 147776062095894
Author(s):  
Rana Mahdi Salih ◽  
Ahmed Sattar Jabbar Al-Zubaydi
Keyword(s):  
Mechanical Properties ◽  
Thermal Conductivity ◽  
Tensile Strength ◽  
Flexural Strength ◽  
Human Hair ◽  
Epoxy Composite ◽  
Sound Intensity ◽  
Sound Insulation ◽  
Building Industry ◽  
Test Results

This research reports the study of epoxy reinforced with human hair as a potential building material for the purpose of acoustic and thermal insulation for building industry. The sound insulation and thermal conductivity were studied for an epoxy composite reinforced with 15% human hair, together with a set of mechanical properties (tensile strength and flexural strength). The sound insulation results proved that the addition of hair led to about 75% loss of the sound intensity compared to the sound intensity noticed for the unreinforced specimen. Thermal conductivity decreased by about 20% with reinforcement. Mechanical properties show a significant improvement, such that flexural strength increased by 25%. The tensile test results showed a higher Young’s modulus and tensile strength for the reinforced specimen by about 50% and 27% respectively. Finally, flexural strength also showed an increase by about 20% after reinforcement.

Sign in / Sign up

Export Citation Format

Share Document