scholarly journals Estimation of Tibiofemoral and Patellofemoral Joint Forces during Squatting and Kneeling

2021 ◽  
Vol 12 (1) ◽  
pp. 255
Author(s):  
Ulrich Glitsch ◽  
Kai Heinrich ◽  
Rolf Peter Ellegast
Keyword(s):  
Knee Joint ◽  
Patellofemoral Joint ◽  
Inverse Dynamics ◽  
Biomechanical Model ◽  
Tibiofemoral Joint ◽  
Joint Force ◽  
Contact Points ◽  
Joint Forces ◽  
Motion Capturing ◽  
Male Subjects

This study examined the differences of knee joint forces between lowering to, or rising from squat, and typical final postures of squatting and kneeling. A biomechanical model of the lower limb was configured considering large knee flexion angles, multiple floor contact points, and the soft tissue contact between the thigh and calf. Inverse dynamics were used to determine muscle and compressive joint forces in the tibiofemoral and patellofemoral joints. Data were obtained from a group of 13 male subjects by means of 3D motion capturing, two force plates, a pressure-sensitive pad, and electromyography. During lowering into the kneeling/squatting positions and rising from them, the model exhibited the anticipated high maximum forces of 2.6 ± 0.39 body weight (BW) and 3.4 ± 0.56 BW in the tibiofemoral and patellofemoral joints. Upon attainment of the static terminal squatting and kneeling positions, the forces fell considerably, remaining within a range of between 0.5 and 0.7 BW for the tibiofemoral joint and 0.9 to 1.1 BW for the patellofemoral joint. The differences of the knee joint forces between the final postures of squatting and kneeling remained on average below 0.25 BW and were significant only for the tibiofemoral joint force.

External Loading at the Knee Joint for Landing Movements in Alpine Skiing

1992 ◽  
Vol 8 (1) ◽  
pp. 62-80 ◽  
Author(s):  
Lynda Read ◽  
Walter Herzog
Keyword(s):  
Knee Joint ◽  
Knee Flexion ◽  
Inverse Dynamics ◽  
Cruciate Ligament ◽  
Acl Injury ◽  
External Loading ◽  
Alpine Skiing ◽  
Joint Forces ◽  
Anterior Cruciate ◽  
Resultant Forces

The purpose of this study was to determine resultant knee joint forces and moments during a specific movement in Alpine ski racers. The movement analyzed consisted of a landing from a bump and the initiation of recovery (if necessary). Resultant loads were obtained using an inverse dynamics approach. Results of two specific skiers are contrasted, one skier landing in good form, the second skier landing in poor form. The skier landing in poor form exhibited larger knee flexion, and larger knee joint resultant forces and moments than the skier landing in good form. The movement of the skier landing in poor form has been associated with isolated anterior cruciate ligament (ACL) injury. However, the data obtained in this study do not indicate that either skier was in danger of ACL injury.

Three-Dimensional Knee Joint Loading in Alpine Skiing: A Comparison Between a Carved and a Skidded Turn

2012 ◽  
Vol 28 (6) ◽  
pp. 655-664 ◽  
Author(s):  
Miriam Klous ◽  
Erich Müller ◽  
Hermann Schwameder
Keyword(s):  
Knee Joint ◽  
Inverse Dynamics ◽  
Small Sample Size ◽  
Three Dimensional ◽  
Small Sample ◽  
High Rate ◽  
Joint Loading ◽  
Joint Forces ◽  
Inverse Dynamics Analysis ◽  
Knee Joint Loading

Limited data exists on knee biomechanics in alpine ski turns despite the high rate of injuries associated with this maneuver. The purpose of the current study was to compare knee joint loading between a carved and a skidded ski turn and between the inner and outer leg. Kinetic data were collected using Kistler mobile force plates. Kinematic data were collected with five synchronized, panning, tilting, and zooming cameras. Inertial properties of the segments were calculated using an extended version of the Yeadon model. Knee joint forces and moments were calculated using inverse dynamics analysis. The obtained results indicate that knee joint loading in carving is not consistently greater than knee joint loading in skidding. In addition, knee joint loading at the outer leg is not always greater than at the inner leg. Differentiation is required between forces and moments, the direction of the forces and moments, and the phase of the turn that is considered. Even though the authors believe that the analyzed turns are representative, results have to be interpreted with caution due to the small sample size.

Anterior Cruciate Ligament Forces in Alpine Skiing

1993 ◽  
Vol 9 (4) ◽  
pp. 260-278 ◽  
Author(s):  
Walter Herzog ◽  
Lynda Read
Keyword(s):  
Anterior Cruciate Ligament ◽  
Knee Joint ◽  
Inverse Dynamics ◽  
Cruciate Ligament ◽  
Symmetric System ◽  
Alpine Skiing ◽  
Loading Conditions ◽  
World Cup ◽  
Joint Forces ◽  
Anterior Cruciate

The purpose of this study was to estimate cruciate ligament forces in Alpine skiing during a movement that has been associated with anterior cruciate ligament (ACL) tears. Resultant knee joint forces and moments were obtained from two skiers during a World Cup Downhill race using an inverse dynamics approach and a 2-D bilaterally symmetric system model. It was found that ACL forces were typically small for both skiers throughout the movement analyzed because quadriceps forces prevented anterior displacement of the tibia relative to the femur at the knee joint angles observed. However, for about 10 ms, loading conditions in the knee joint of Subject 2 (who displayed poor form) were such that large ACL forces may have been present. These particular loading conditions were never observed in Subject 1, who displayed good form. Since neither of the skiers was injured, it is not possible to draw firm conclusions about isolated ACL tears in Alpine skiing from the data at hand.

A Video Technique for Obtaining 3-D Coordinates in Alpine Skiing

1996 ◽  
Vol 12 (1) ◽  
pp. 104-115 ◽  
Author(s):  
Werner Nachbauer ◽  
Peter Kaps ◽  
Benno Nigg ◽  
Fritz Brunner ◽  
Alexander Lutz ◽  
...  
Keyword(s):  
Knee Joint ◽  
Linear Transformation ◽  
Inverse Dynamics ◽  
Video Image ◽  
Alpine Skiing ◽  
Control Points ◽  
Reasonable Accuracy ◽  
Large Object ◽  
Object Space ◽  
Joint Forces

A video technique to obtain 3-D data in an Alpine skiing competition was investigated. The flight and landing phases of a jump were recorded during the 1994 Olympic combined downhill race. A direct linear transformation (DLT) implementation was applied, which computes the DLT parameters for each video image of each camera separately. As a consequence, one is able to pan and tilt the cameras and zoom the lenses. The problem of distributing control points in the large object space could be solved satisfactorily. The method proved to be suitable for obtaining 3-D data with reasonable accuracy, which is even sufficient for inverse dynamics. The computed resultant knee joint forces and moments compare well with results reported by other authors.

scholarly journals Determination of Joint Load of Human Lower Limb by Using 2D Inverse Dynamics Modelling

2019 ◽  
Vol 9 (1) ◽  
pp. 5723-5727
Keyword(s):  
Lower Limb ◽  
Inverse Dynamics ◽  
Joint Force ◽  
Joint Forces ◽  
Limb Kinematics ◽  
Dynamics Modelling ◽  
Squat Lifting ◽  
Joint Load ◽  
Joint Loads ◽  
Matlab Programming

The human lower limb is a major part of the human body that is exposed to high joint load during daily activities. Different lifestyles and cultural activities can affect the loading condition generated at the joint during motion. For instance, deep squatting is more frequently performed by Asians compared to Europeans e.g. kneeing on tatami among Japanese and sitting position during prayer among Muslims. The aim of this research is to determine the joint load of the human lower limb during the squat lifting movement by using inverse dynamics of 2-dimensional (2D) human lower limb model. The 2D inverse dynamics modelling was used to describe and compute all the joint force reactions from the known ground reaction and lower limb kinematics. In this study, 2D human lower limb model was analysed during the squat lifting movement. Inverse dynamics computation was performed using MATLAB programming based on Newton-Euler equations to determine the joint forces and moments. The joint loads at ankle, knee and hip joints for every knee flexion angle were obtained and the maximum forces at the ankle, knee and hip were 613.9, 614.1 and 596.1 N, respectively.

Functional Evaluation of a Personalized Orthosis for Knee Osteoarthritis - A Motion Capture Analysis

2021 ◽  
Author(s):  
Martin Huber ◽  
Matthew Eschbach ◽  
Kazem Kazerounian ◽  
Horea T. Ilies
Keyword(s):  
Knee Joint ◽  
Knee Osteoarthritis ◽  
Motion Capture ◽  
Inverse Dynamics ◽  
Statistical Significance ◽  
Knee Kinematics ◽  
Contact Forces ◽  
Patient Specific ◽  
Functional Evaluation ◽  
Shock Absorption

Abstract Knee osteoarthritis (OA) is a disease that compromises the cartilage inside the knee joint, resulting in pain and impaired mobility. Bracing is a common treatment, however currently prescribed braces cannot treat bicompartmental knee OA, fail to consider the muscle weakness that typically accompanies the disease, and utilize hinges that restrict the knee's natural biomechanics. We have developed and evaluated a brace which addresses these shortcomings. This process has respected three principal design goals: reducing the load experienced across the entire knee joint, generating a supportive moment to aid the muscles in shock absorption, and interfering minimally with gait kinematics. Load reduction is achieved via the compression of medial and lateral leaf springs, and magnetorheological dampers provide the supportive moment during knee loading. A novel, personalized joint mechanism replaces a traditional hinge to reduce interference with knee kinematics. Using motion capture gait analysis, we evaluated the basic functionality of a prototype device. We calculated, via inverse dynamics analysis, the reaction forces at the knee joint and the moments generated by the leg muscles during gait. Comparing these values between braced and unbraced trials allowed us to evaluate the system's effectiveness. Kinematic measurements showed the extent to which the brace interfered with natural gait characteristics. Of the three design goals: a reduction in knee contact forces was demonstrated; increased shock absorption was observed, but not to statistical significance; and natural gait was largely preserved. The techniques presented in this paper could lead to improved OA treatment through patient-specific braces.

Effects of Body Weight Modification on Internal Knee Contact Forces During Gait

2013 ◽  
Author(s):  
Allison L. Kinney ◽  
Heather K. Vincent ◽  
Melinda K. Harman ◽  
James Coburn ◽  
Darryl D. D’Lima ◽  
...  
Keyword(s):  
Body Weight ◽  
Risk Factor ◽  
Knee Joint ◽  
Inverse Dynamics ◽  
Contact Forces ◽  
Weight Changes ◽  
Body Weight Changes ◽  
Total Knee ◽  
Knee Joint Loading ◽  
Knee Load

Obesity is commonly considered a risk factor for the development of knee osteoarthritis [1]. Previous studies have shown that reductions in body weight correspond to reductions in total knee joint compressive forces (as calculated by inverse dynamics) [2–4]. A recent study showed that external knee load measurements are not strong predictors of internal knee contact forces [5]. Therefore, direct measurement of knee contact force is important for understanding how body weight changes impact knee joint loading. Force-measuring knee implants can directly measure internal knee contact forces [6].

Design and Test of a Biomechanical Model for the Estimation of Knee Joint Angle During Indoor Rowing: Implications for FES-Rowing Protocols in Paraplegia

2018 ◽  
Vol 26 (11) ◽  
pp. 2145-2152 ◽  
Author(s):  
Taian Vieira ◽  
Giacinto Luigi Cerone ◽  
Laura Gastaldi ◽  
Stefano Pastorelli ◽  
Liliam F. Oliveira ◽  
...  
Keyword(s):  
Knee Joint ◽  
Joint Angle ◽  
Biomechanical Model ◽  
Knee Joint Angle
Sign in / Sign up

Export Citation Format

Share Document