scholarly journals A Numerical Study of the Stiffness and Strength of Cross-Laminated Timber Wall-to-Floor Connections under Compression Perpendicular to the Grain

Buildings ◽  
2021 ◽  
Vol 11 (10) ◽  
pp. 442
Author(s):  
Shaheda T. Akter ◽  
Michael Schweigler ◽  
Erik Serrano ◽  
Thomas K. Bader
Keyword(s):  
Finite Element ◽  
Annual Ring ◽  
Numerical Study ◽  
Plastic Material ◽  
Element Model ◽  
Material Behavior ◽  
Thickness Effect ◽  
Parameter Study ◽  
Regression Equations ◽  
Cross Laminated Timber

The use of cross-laminated timber (CLT) in multi-story buildings is increasing due to the potential of wood to reduce green house gas emissions and the high load-bearing capacity of CLT. Compression perpendicular to the grain (CPG) in CLT is an important design aspect, especially in multi-storied platform-type CLT buildings, where CPG stress develops in CLT floors due to loads from the roof or from upper floors. Here, CPG of CLT wall-to-floor connections are studied by means of finite element modeling with elasto-plastic material behavior based on a previously validated Quadratic multi-surface (QMS) failure criterion. Model predictions were first compared with experiments on CLT connections, before the model was used in a parameter study, to investigate the influence of wall and floor thicknesses, the annual ring pattern of the boards and the number of layers in the CLT elements. The finite element model agreed well with experimental findings. Connection stiffness was overestimated, while the strength was only slightly underestimated. The parameter study revealed that the wall thickness effect on the stiffness and strength of the connection was strongest for the practically most relevant wall thicknesses between 80 and about 160 mm. It also showed that an increasing floor thickness leads to higher stiffness and strength, due to the load dispersion effect. The increase was found to be stronger for smaller wall thicknesses. The influence of the annual ring orientation, or the pith location, was assessed as well and showed that boards cut closer to the pith yielded lower stiffness and strength. The findings of the parameter study were fitted with regression equations. Finally, a dimensionless ratio of the wall-to-floor thickness was used for deriving regression equations for stiffness and strength, as well as for load and stiffness increase factors, which could be used for the engineering design of CLT connections.

Elephant Foot Buckling Analysis of Large Unanchored Oil Storage Tanks With Tapered Shells Subjected to Foundation Settlement

2020 ◽  
Author(s):  
Lei Shi ◽  
Xiaolin Wang ◽  
Liang Chang ◽  
Xue Li
Keyword(s):  
Finite Element ◽  
Numerical Study ◽  
Plastic Material ◽  
Element Model ◽  
Nonlinear Boundary Conditions ◽  
Storage Tanks ◽  
Nonlinear Stabilization ◽  
Buckling Strength ◽  
Oil Storage ◽  
Steel Tank

Abstract This paper presents an numerical study on a large unanchored open-topped steel tank. The buckling behaviors of the tank are analyzed using the finite element computer package ANSYS by means of nonlinear stabilization algorithm. The effects of foundation harmonic settlement on the elephant foot buckling strength of large unanchored open-topped oil storage tanks with tapered shells under axial compression are explored by numerical modeling. Various items of actual geometrical structure which involve concrete ringwall foundation of tank, unanchored bottom with slope, shell tapering from the base to the top, wind girders and supports, top angles, stiffening rings and support plates are presented thoroughly in the non-symmetrical 3D finite element model. Geometric nonlinearity, nonlinear boundary conditions and elastic plastic material of Ramberg-Osgood model are involved simultaneously in simulate course. The obtained solutions are displayed graphically for selected values of system parameters: harmonic settlement amplitude, harmonic number, and critical buckling stress of axially compressed oil tank. The results will provide insights into the relationship between foundation harmonic settlement and buckling strength of the large cylinders.

Computational and Experimental Study of Temperature Distribution and Residual Stress in Butt-Joint TIG Welds

2011 ◽  
Vol 480-481 ◽  
pp. 459-465
Author(s):  
Kuang Hung Tseng ◽  
Kuan Lung Chen
Keyword(s):  
Experimental Data ◽  
Residual Stress ◽  
Finite Element ◽  
Temperature Distribution ◽  
Finite Element Model ◽  
Power Distribution ◽  
Plastic Material ◽  
Element Model ◽  
Butt Joint ◽  
Material Behavior

This work conducted a non-linear finite element model associated with arc efficiency to simulate the temperature distribution and residual stress. A three-dimensional finite element analysis of temperature and stress in butt-joint TIG welds was performed using commercial software ANSYS. This model includes adjusting Gaussian distribution heat flux, alternating temperature dependent material properties, and managing thermal elasto-plastic material behavior. Computational results for both the temperature distribution and the residual stress are compared with available experimental data to confirm the accuracy of this technique. The simulated results of temperature distribution and residual stress are in good agreement with corresponding experimental data. The greatest value of this work does not lie in its ability to predict the magnitude and distribution of weld temperature and residual stress. Rather, this work proposed that prediction errors in a finite element model can be eliminated by modifying the arc power distribution function.

scholarly journals Numerical investigation of the effects of unsupported railway sleepers on train-induced environmental vibrations

2017 ◽  
Vol 36 (2) ◽  
pp. 160-176 ◽  
Author(s):  
Seyed-Ali Mosayebi ◽  
Morteza Esmaeili ◽  
Jabbar-Ali Zakeri
Keyword(s):  
Finite Element ◽  
Element Model ◽  
Two Dimensions ◽  
Railway Track ◽  
Sensitivity Analyses ◽  
Regression Equations ◽  
The Finite Element Method ◽  
Technical Literature ◽  
Support Force ◽  
Comparison Of The Results

Review of technical literature regarding to train-induced vibrations shows that the effects of unsupported railway sleepers on this issue have been less investigated. So, the present study was devoted to numerical investigations of the mentioned issue. In this regard, first the problem of longitudinal train–track dynamic interaction was simulated in two dimensions by using the finite element method and the developed model was validated through comparison of the results with those obtained by previous researchers. In the next stage, a series of sensitivity analyses were accomplished to account for the effects of value of gap beneath the unsupported sleeper(s) and the track support stiffness on increasing the sleeper displacement and track support force. Moreover, the raised sleeper support force was introduced as applied load to a two-dimensional plane strain finite element model of track in lateral section and consequently the train-induced vibrations were assessed. As a result, a series of regression equations were established between the peak particle velocity in the surrounding environment of railway track and the sleeper support stiffness for tracks without unsupported sleepers and with one and two unsupported sleepers.

Elasto-Plastic Coupled Temperature-Displacement Finite Element Analysis of Two-Dimensional Rolling-Sliding Contact With a Translating Heat Source

1991 ◽  
Vol 113 (1) ◽  
pp. 93-101 ◽  
Author(s):  
S. M. Kulkarni ◽  
C. A. Rubin ◽  
G. T. Hahn
Keyword(s):  
Finite Element ◽  
Half Space ◽  
Plastic Material ◽  
Element Model ◽  
Rolling Contact ◽  
Two Dimensional ◽  
Element Analysis ◽  
Element Mesh ◽  
Perfectly Plastic ◽  
Elastic Perfectly Plastic

The present paper, describes a transient translating elasto-plastic thermo-mechanical finite element model to study 2-D frictional rolling contact. Frictional two-dimensional contact is simulated by repeatedly translating a non-uniform thermo-mechanical distribution across the surface of an elasto-plastic half space. The half space is represented by a two dimensional finite element mesh with appropriate boundaries. Calculations are for an elastic-perfectly plastic material and the selected thermo-physical properties are assumed to be temperature independent. The paper presents temperature variations, stress and plastic strain distributions and deformations. Residual tensile stresses are observed. The magnitude and depth of these stresses depends on 1) the temperature gradients and 2) the magnitudes of the normal and tangential tractions.

Shakedown Limit Load Determination for a Kinematically Hardening 90-Degree Pipe Bend Subjected to Constant Internal Pressure and Cyclic Bending

2007 ◽  
Author(s):  
Hany F. Abdalla ◽  
Mohammad M. Megahed ◽  
Maher Y. A. Younan
Keyword(s):  
Finite Element ◽  
Internal Pressure ◽  
Plastic Material ◽  
Kinematic Hardening ◽  
Limit Load ◽  
Material Behavior ◽  
Pipe Bend ◽  
Cyclic Bending ◽  
Perfectly Plastic ◽  
Shakedown Limit

A simplified technique for determining the shakedown limit load of a structure employing an elastic-perfectly-plastic material behavior was previously developed and successfully applied to a long radius 90-degree pipe bend. The pipe bend is subjected to constant internal pressure and cyclic bending. The cyclic bending includes three different loading patterns namely; in-plane closing, in-plane opening, and out-of-plane bending moment loadings. The simplified technique utilizes the finite element method and employs small displacement formulation to determine the shakedown limit load without performing lengthy time consuming full cyclic loading finite element simulations or conventional iterative elastic techniques. In the present paper, the simplified technique is further modified to handle structures employing elastic-plastic material behavior following the kinematic hardening rule. The shakedown limit load is determined through the calculation of residual stresses developed within the pipe bend structure accounting for the back stresses, determined from the kinematic hardening shift tensor, responsible for the translation of the yield surface. The outcomes of the simplified technique showed very good correlation with the results of full elastic-plastic cyclic loading finite element simulations. The shakedown limit moments output by the simplified technique are used to generate shakedown diagrams of the pipe bend for a spectrum of constant internal pressure magnitudes. The generated shakedown diagrams are compared with the ones previously generated employing an elastic-perfectly-plastic material behavior. These indicated conservative shakedown limit moments compared to the ones employing the kinematic hardening rule.

Numerical Study for Global Detection of Cracks Embedded in Beams

1999 ◽  
Author(s):  
S. A. Lipsey ◽  
Y. W. Kwon
Keyword(s):  
Finite Element ◽  
Dynamic Analysis ◽  
Natural Frequency ◽  
Mode Shape ◽  
Numerical Study ◽  
Element Model ◽  
Mode Shapes ◽  
Linear Effect ◽  
Modes Of Vibration ◽  
Damage Simulation

Abstract Damage reduces the flexural stiffness of a structure, thereby altering its dynamic response, specifically the natural frequency, damping values, and the mode shapes associated with each natural frequency. Considerable effort has been put into obtaining a correlation between the changes in these parameters and the location and amount of the damage in beam structures. Most numerical research employed elements with reduced beam dimensions or material properties such as modulus of elasticity to simulate damage in the beam. This approach to damage simulation neglects the non-linear effect that a crack has on the different modes of vibration and their corresponding natural frequencies. In this paper, finite element modeling techniques are utilized to directly represent an embedded crack. The results of the dynamic analysis are then compared to the results of the dynamic analysis of the reduced modulus finite element model. Different modal parameters including both mode shape displacement and mode shape curvature are investigated to determine the most sensitive indicator of damage and its location.

Étude de la réouverture de la lagune du Havre aux Basques. I. Modélisation numérique des conditions d'écoulement

1995 ◽  
Vol 22 (1) ◽  
pp. 55-71
Author(s):  
Y. Ouellet ◽  
A. Khelifa ◽  
J.-F. Bellemare
Keyword(s):  
Finite Element ◽  
Numerical Study ◽  
Element Model ◽  
Two Dimensional ◽  
Flow Conditions ◽  
Modélisation Numérique ◽  
Tidal Flows ◽  
Dimensional Finite Element ◽  
The Stability ◽  
La Madeleine

A numerical study based on a two-dimensional finite element model has been conducted to analyze flow conditions associated with different possible designs for the reopening of Havre aux Basques lagoon, located in Îles de la Madeleine, in the middle of the Gulf of St. Lawrence. More specifically, the study has been done to better define the depth and geometry of the future channel as well as its orientation with regard to tidal flows within the inlet and the lagoon. Results obtained from the model have been compared and analyzed to put forward some recommendations about choice of a design insuring the stability of the inlet with tidal flows. Key words: numerical model, finite element, lagoon, reopening, Havre aux Basques, Îles de la Madeleine.

A FINITE ELEMENT MODEL FOR COMPRESSIVE ICE LOADS BASED ON A MOHR-COULOMB MATERIAL AND THE NODE SPLITTING TECHNIQUE

2021 ◽  
pp. 1-33
Author(s):  
Hauke Herrnring ◽  
Søren Ehlers
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Element Model ◽  
Material Behavior ◽  
Double Pendulum ◽  
Strain Rates ◽  
Splitting Technique ◽  
Structure Interaction ◽  
Node Splitting ◽  
Brittle Mode

Abstract This paper presents a finite element model for the simulation of ice-structure interaction problems, which are dominated by crushing. The failure mode of ice depends significantly on the strain rate. At low strain rates the ice behaves ductile, whereas at high strain rates ice reacts in brittle mode. This paper focuses on the brittle mode, which is the dominating mode for ship-ice interactions. A multitude of numerical approaches for the simulation of ice can be found in the literature. Nevertheless, the literature approaches do not seem suitable for the simulation of continuous ice-structure interaction processes at low and high confinement ratios in brittle mode. Therefore, this paper seeks to simulate the ice-structure interaction with the finite element method (FEM). The objective of the here introduced Mohr-Coulomb Nodal Split (MCNS) model is to represent the essential material behavior of ice in an efficient formulation. To preserve mass and energy as much as possible, the node splitting technique is applied, instead of the frequently used element erosion technique. The intention of the presented model is not to reproduce individual cracks with high accuracy, because this is not possible with a reasonable element size, due to the large number of crack fronts forming during the ice-structure interaction process. To validate the findings of the model, the simulated maximum ice forces and contact pressures are compared with ice-extrusion and double pendulum tests. During validation, the MCNS model shows a very good agreement with these experimental values.

scholarly journals Modeling inflatable fabric with undevelopable surfaces by motion folding method

2019 ◽  
Vol 14 ◽  
pp. 155892501988640
Author(s):  
Xiao-Shun Zhao ◽  
He Jia ◽  
Zhihong Sun ◽  
Li Yu
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Numerical Study ◽  
Technical Problem ◽  
Three Dimensional ◽  
Element Model ◽  
Model Errors ◽  
Folding Model ◽  
Study Results ◽  
The Stability

At present, most space inflatable structures are composed of flexible inflatable fabrics with complex undevelopable surfaces. It is difficult to establish a multi-dimensional folding model for this type of structure. To solve this key technical problem, the motion folding method is proposed in this study. First, a finite element model with an original three-dimensional surface was flattened with a fluid structure interaction algorithm. Second, the flattened surface was folded based on the prescribed motion of the node groups, and the final folding model was obtained. The fold modeling process of this methodology was consistent with the actual folding processes. Because the mapping relationship between the original finite element model and the final folding model was unchanged, the initial stress was used to modify the model errors during folding process of motion folding method. The folding model of an inflatable aerodynamic decelerator, which could not be established using existing folding methods, was established by using motion folding method. The folding model of the inflatable aerodynamic decelerator showed that the motion folding method could achieve multi-dimensional folding and a high spatial compression rate. The stability and regularity of the inflatable aerodynamic decelerator numerical inflation process and the consistency of the inflated and design shapes indicated the reliability, applicability, and feasibility of the motion folding method. The study results could provide a reference for modeling complex inflatable fabrics and promote the numerical study of inflatable fabrics.

Numerical Study of Welding Sequence on the Residual Stress Field in a Thick-Walled Tee Joint

2011 ◽  
Vol 219-220 ◽  
pp. 1211-1214
Author(s):  
Wei Jiang
Keyword(s):  
Residual Stress ◽  
Finite Element ◽  
Numerical Study ◽  
Three Dimensional ◽  
Element Model ◽  
Residual Stress Field ◽  
Factors Affecting ◽  
Welding Sequence ◽  
Welding Sequences ◽  
Three Dimensional Finite Element

Finite element simulation is an efficient method for studying factors affecting weld-induced residual stress distributions. In this paper, a validated three-dimensional finite element model consisting of sequentially coupled thermal and structural analyses was developed. Three possible symmetrical welding sequences, i.e. one-welder, two-welder and four-welder sequence, which were perceived to generate the least distortion in actual welding circumstances, were proposed and their influences on the residual stress fields in a thick-walled tee joint were investigated. Appropriate conclusions and recommendations regarding welding sequences are presented.

Sign in / Sign up

Export Citation Format

Share Document