scholarly journals High Surface Area Nanoporous Activated Carbons Materials from Areca catechu Nut with Excellent Iodine and Methylene Blue Adsorption

2021 ◽  
Vol 8 (1) ◽  
pp. 2
Author(s):  
Sahira Joshi ◽  
Rekha Goswami Shrestha ◽  
Raja Ram Pradhananga ◽  
Katsuhiko Ariga ◽  
Lok Kumar Shrestha
Keyword(s):  
Methylene Blue ◽  
Surface Area ◽  
Carbon Materials ◽  
High Surface ◽  
High Surface Area ◽  
Textural Properties ◽  
Mixing Ratio ◽  
Surface Functional Groups ◽  
Methylene Blue Adsorption ◽  
Areca Catechu

Nanoporous carbon materials from biomass exhibit a high surface area due to well-defined pore structures. Therefore, they have been extensively used in separation and purification technologies as efficient adsorbents. Here, we report the iodine and methylene blue adsorption properties of the hierarchically porous carbon materials prepared from Areca catechu nut. The preparation method involves the phosphoric acid (H3PO4) activation of the Areca catechu nut powder. The effects of carbonization conditions (mixing ratio with H3PO4, carbonization time, and carbonization temperature) on the textural properties and surface functional groups were studied. The optimum textural properties were obtained at a mixing ratio of 1:1, carbonized for 3 h at 400 °C, and the sample achieved a high specific surface area of 2132.1 m2 g−1 and a large pore volume of 3.426 cm3 g−1, respectively. The prepared materials have amorphous carbon structures and contain oxygenated surface functional groups. Due to the well-defined micro-and mesopore structures with the high surface area and large pore volume, the optimal sample showed excellent iodine and methylene blue adsorption. The iodine number and methylene blue values were ca. 888 mg g−1 and 369 mg g−1, respectively. The batch adsorption studies of methylene dye were affected by pH, adsorbent dose, contact time, and initial concentration. The optimum parameters for the methylene blue adsorption were in alkaline pH, adsorbent dose of 2.8 g L−1, and contact time of 180 min. Equilibrium data could be best represented by the Langmuir isotherm model with a monolayer adsorption capacity of 333.3 mg g−1. Thus, our results demonstrate that the Areca catechu nut has considerable potential as the novel precursor material for the scalable production of high surface area hierarchically porous carbon materials that are essential in removing organic dyes from water.

scholarly journals Rice Husk-Derived High Surface Area Nanoporous Carbon Materials with Excellent Iodine and Methylene Blue Adsorption Properties

2019 ◽  
Vol 5 (1) ◽  
pp. 10 ◽  
Author(s):  
Lok Shrestha ◽  
Mamata Thapa ◽  
Rekha Shrestha ◽  
Subrata Maji ◽  
Raja Pradhananga ◽  
...  
Keyword(s):  
Methylene Blue ◽  
Surface Area ◽  
Rice Husk ◽  
Carbon Materials ◽  
High Surface ◽  
High Surface Area ◽  
Nanoporous Carbon ◽  
Adsorption Properties ◽  
Methylene Blue Adsorption ◽  
Nanoporous Carbon Materials

Iodine and methylene blue adsorption properties of the high surface area nanoporous carbon materials derived from agro-waste and rice husk is reported. Rice husk was pre-carbonized at 300 °C in air followed by leaching out the silica nanoparticles by extraction with sodium hydroxide solution. The silica-free rice husk char was mixed with chemical activating agents sodium hydroxide (NaOH), zinc chloride (ZnCl2), and potassium hydroxide (KOH) separately at a mixing ratio of 1:1 (wt%) and carbonized at 900 °C under a constant flow of nitrogen. The prepared carbon materials were characterized by scanning electron microscopy (SEM), Fourier transformed-infrared spectroscopy (FT-IR), powder X-ray diffraction (pXRD), and Raman scattering. Due to the presence of bimodal micro- and mesopore structures, KOH activated samples showed high specific surface area ca. 2342 m2/g and large pore volume ca. 2.94 cm3/g. Oxygenated surface functional groups (hydroxyl, carbonyl, and carboxyl) were commonly observed in all of the samples and were essentially non-crystalline porous particle size of different sizes (<200 μm). Adsorption study revealed that KOH activated samples could be excellent material for the iodine and methylene blue adsorption from aqueous phase. Iodine and methylene blue number were ca. 1726 mg/g and 608 mg/g, respectively. The observed excellent iodine and methylene blue adsorption properties can be attributed to the well-developed micro- and mesopore structure in the carbon material. This study demonstrates that the agricultural waste, rice husk, and derived nanoporous carbon materials would be excellent adsorbent materials in water purifications.

NaOH-activated carbon of high surface area produced from coconut shell: Kinetics and equilibrium studies from the methylene blue adsorption

2011 ◽  
Vol 174 (1) ◽  
pp. 117-125 ◽  
Author(s):  
André L. Cazetta ◽  
Alexandro M.M. Vargas ◽  
Eurica M. Nogami ◽  
Marcos H. Kunita ◽  
Marcos R. Guilherme ◽  
...  
Keyword(s):  
Methylene Blue ◽  
Activated Carbon ◽  
Surface Area ◽  
High Surface ◽  
High Surface Area ◽  
Coconut Shell ◽  
Equilibrium Studies ◽  
Methylene Blue Adsorption

scholarly journals Dopamine Assisted One-Step Pyrolysis of Glucose for the Preparation of Porous Carbon with A High Surface Area

Nanomaterials ◽  
2018 ◽  
Vol 8 (10) ◽  
pp. 854 ◽  
Author(s):  
Hanbo Xiao ◽  
Cheng-an Tao ◽  
Yujiao Li ◽  
Xianzhe Chen ◽  
Jian Huang ◽  
...  
Keyword(s):  
Surface Area ◽  
Porous Carbon ◽  
Carbon Materials ◽  
High Current Density ◽  
High Surface ◽  
High Surface Area ◽  
Energy Storage Materials ◽  
One Pot ◽  
Component Structure ◽  
Porous Carbon Materials

Herein, a facile dopamine assisted one-pot synthesis approach is proposed for the preparation of porous carbon with a specific surface area (SSA) up to 2593 m2/g through the direct pyrolysis of a mixture of glucose, NH4Cl, and dopamine hydrochloride (DAH). The glucose is adopted as the carbon source and foaming agent, NH4Cl is used as the blowing agent, and DAH is served as collaborative carbon precursor as well as the nitrogen source for the first time. The effect of dopamine on the component, structure, and SSA of the as-prepared porous carbon materials are systematically studied. The moderate addition of dopamine, which influences the condensation and polymerization of glucose, matches better with ammonium salt decomposition. The SSA of porous carbon increases first and then decreases with the increasing amount of dopamine. In our case, the porous carbon produced with 5 wt% dopamine (PC-5) achieves the maximum SSA of up to 2593 m2/g. Accordingly, it also shows the greatest electrochemical performance. The PC-5 shows a capacitance of 96.7 F/g calculated from the discharge curve at 1 A/g. It also has a good capacitive rate capacity, the specific capacitance can still maintain 80%, even at a high current density of 10 A/g. Moreover, PC-5 exhibits a good cycling stability of 98.1% capacitive retention after 1000 cycles. The proposed method may show promising prospects for preparing porous carbon materials as advanced energy storage materials, storage, and catalyst supports.

Morphology dependent adsorption of methylene blue on trititanate nanoplates and nanotubes prepared by the hydrothermal treatment of TiO2

2016 ◽  
Vol 75 (2) ◽  
pp. 350-357
Author(s):  
Graham Dawson ◽  
Wei Chen ◽  
Luhua Lu ◽  
Kai Dai
Keyword(s):  
Methylene Blue ◽  
Adsorption Capacity ◽  
Surface Area ◽  
Pore Volume ◽  
Hydrothermal Reaction ◽  
Low Cost ◽  
High Surface ◽  
High Surface Area ◽  
High Capacity ◽  
Adsorption Properties

The adsorption properties of two nanomorphologies of trititanate, nanotubes (TiNT) and plates (TiNP), prepared by the hydrothermal reaction of concentrated NaOH with different phases of TiO2, were examined. It was found that the capacity for both morphologies towards methylene blue (MB), an ideal pollutant, was extremely high, with the TiNP having a capacity of 130 mg/g, higher than the TiNT, whose capacity was 120 mg/g at 10 mg/L MB concentration. At capacity, the well-dispersed powders deposit on the floor of the reaction vessel. The two morphologies had very different structural and adsorption properties. TiNT with high surface area and pore volume exhibited exothermic monolayer adsorption of MB. TiNP with low surface area and pore volume yielded a higher adsorption capacity through endothermic multilayer adsorption governed by pore diffusion. TiNP exhibited a higher negative surface charge of −23 mV, compared to −12 mV for TiNT. The adsorption process appears to be an electrostatic interaction, with the cationic dye attracted more strongly to the nanoplates, resulting in a higher adsorption capacity and different adsorption modes. We believe this simple, low cost production of high capacity nanostructured adsorbent material has potential uses in wastewater treatment.

scholarly journals Microporous activated carbon developed from KOH activated biomass waste: surface mechanistic study of methylene blue dye adsorption

2021 ◽  
Author(s):  
Ali H. Jawad ◽  
Ahmed Saud Abdulhameed ◽  
Noor Nazihah Bahrudin ◽  
Nurul Nadiah Mohd Firdaus Hum ◽  
S. N. Surip ◽  
...  
Keyword(s):  
Methylene Blue ◽  
Activated Carbon ◽  
Surface Area ◽  
Sugarcane Bagasse ◽  
High Surface ◽  
High Surface Area ◽  
Dye Adsorption ◽  
Type I ◽  
Order Kinetic ◽  
Bagasse Waste

Abstract In this work, sugarcane bagasse waste (SBW) was used as a lignocellulosic precursor to develop a high surface area activated carbon (AC) by thermal treatment of the SBW impregnated with KOH. This sugarcane bagasse waste activated carbon (SBWAC) was characterized by means of crystallinity, porosity, surface morphology and functional groups availability. The SBWAC exhibited Type I isotherm which corresponds to microporosity with high specific surface area of 709.3 m2/g and 6.6 nm of mean pore diameter. Further application of SBWAC as an adsorbent for methylene blue (MB) dye removal demonstrated that the adsorption process closely followed the pseudo-second order kinetic and Freundlich isotherm models. On the other hand, thermodynamic study revealed the endothermic nature and spontaneity of MB dye adsorption on SBWAC with high acquired adsorption capacity (136.5 mg/g). The MB dye adsorption onto SBWAC possibly involved electrostatic interaction, H-bonding and π-π interaction. This work demonstrates SBW as a potential lignocellulosic precursor to produce high surface area AC that can potentially remove more cationic dyes from the aqueous environment.

scholarly journals Sorghum-Waste-Derived High-Surface Area KOH-Activated Porous Carbon for Highly Efficient Methylene Blue and Pb(II) Removal

ACS Omega ◽  
2020 ◽  
Vol 5 (23) ◽  
pp. 13548-13556 ◽  
Author(s):  
Junhua Hou ◽  
Yijian Liu ◽  
Shikai Wen ◽  
Weitao Li ◽  
Riquan Liao ◽  
...  
Keyword(s):  
Methylene Blue ◽  
Surface Area ◽  
Porous Carbon ◽  
High Surface ◽  
High Surface Area ◽  
Highly Efficient

scholarly journals Structural Flexibility in Activated Carbon Materials Prepared under Harsh Activation Conditions

Materials ◽  
2019 ◽  
Vol 12 (12) ◽  
pp. 1988 ◽  
Author(s):  
Fabiano Gomes Ferreira de Paula ◽  
Ignacio Campello-Gómez ◽  
Paulo Fernando Ribeiro Ortega ◽  
Francisco Rodríguez-Reinoso ◽  
Manuel Martínez-Escandell ◽  
...  
Keyword(s):  
Activated Carbon ◽  
Surface Area ◽  
Structural Changes ◽  
Organic Molecules ◽  
Carbon Materials ◽  
High Surface ◽  
High Surface Area ◽  
Koh Activation ◽  
3D Network ◽  
Activation Conditions

Although traditionally high-surface area carbon materials have been considered as rigid structures with a disordered three dimensional (3D) network of graphite microdomains associated with a limited electrical conductivity (highly depending on the porous structure and surface chemistry), here we show for the first time that this is not the case for activated carbon materials prepared using harsh activation conditions (e.g., KOH activation). In these specific samples a clear structural re-orientation can be observed upon adsorption of different organic molecules, the structural changes giving rise to important changes in the electrical resistivity of the material. Whereas short chain hydrocarbons and their derivatives give rise to an increased resistivity, the contrary occurs for longer-chain hydrocarbons and/or alcohols. The high sensitivity of these high-surface area carbon materials towards these organic molecules opens the gate towards their application for sensing devices.

scholarly journals Synthesis of a high-surface area V2O5/TiO2–SiO2 catalyst and its application in the visible light photocatalytic degradation of methylene blue

RSC Advances ◽  
2019 ◽  
Vol 9 (42) ◽  
pp. 24368-24376 ◽  
Author(s):  
Ajay Kumar Adepu ◽  
Srinath Goskula ◽  
Suman Chirra ◽  
Suresh Siliveri ◽  
Sripal Reddy Gujjula ◽  
...  
Keyword(s):  
Methylene Blue ◽  
Visible Light ◽  
Surface Area ◽  
High Surface ◽  
High Surface Area ◽  
Bet Surface Area ◽  
Titanium Silicate ◽  
Ft Ir ◽  
Synthesized Materials ◽  
Visible Light Photocatalytic

In the present study, we synthesized several high-surface area V2O5/TiO2–SiO2 catalysts (vanado titanium silicate, VTS). The synthesized materials are characterized by PXRD, FE-SEM/EDAX, TEM, BET-surface area, FT-IR, UV-Vis, XPS, fluorescence and photocatalytic studies.

Sign in / Sign up

Export Citation Format

Share Document