scholarly journals Spectroscopic and Microscopic Correlation of SRO-HFCVD Films on Quartz and Silicon

Crystals ◽  
2020 ◽  
Vol 10 (2) ◽  
pp. 127
Author(s):  
Haydee Martínez Hernández ◽  
José Luna López ◽  
José Hernández de la Luz ◽  
Adan Luna Flores ◽  
Karim Monfil Leyva ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Heat Treatment ◽  
Thermal Treatment ◽  
Single Layer ◽  
Nanocrystal Size ◽  
Silicon Nanocrystal ◽  
Grown Layer ◽  
Layer Film ◽  
Heat Treated ◽  
Vis Spectroscopy

This work is focused on making a correlation between results obtained by using spectroscopy and microscopy techniques from single and twofold-layer Silicon-Rich Oxide (SRO) films. SRO films single-layer and twofold-layer characterizations were compared considering the conditions as-grown and with thermal treatment at 1100 °C for 60 min in a nitrogen atmosphere. The thickness of the single-layer film is 324.7 nm while for the twofold-layer film it is 613.2 nm; after heat-treated, both thicknesses decreased until 28.8 nm. X-ray Photoelectron Spectroscopy shows changes in the excess-silicon in single-layer SRO films, with 10% in as-grown films and decreases to 5% for the heat-treated films. Fourier Transform Infrared Spectroscopy (FTIR) exhibits three characteristic vibrational modes of SiO2, as well as, the vibrating modes associated with the Si-H bonds, which disappear after the heat treatment. With UV–Vis spectroscopy results we obtained the absorbance and the absorption coefficient for the SRO films in order to calculate the optical bandgap energy (Egopt), which increased with heat-treatment. The energy peaks of the photoluminescence spectra were used to calculate the silicon nanocrystal size, obtaining thus an average size of 1.89 ± 0.32 nm for the as-grown layer, decreasing the size to 1.64 ± 0.01 nm with the thermal treatment. On the other hand, scanning electron microscopy and high-resolution transmission electron microscopy images confirm the thickness of the twofold-layer SRO films as 628 nm for the as-grown layer and 540 nm for the layer with heat-treatment, and the silicon nanocrystal size of 2.3 ± 0.6 nm for the films with thermal treatment.

Copper(I) Halide Nanoparticle-dispersed Glasses Prepared by Copper Staining

2005 ◽  
Vol 20 (9) ◽  
pp. 2480-2485 ◽  
Author(s):  
Kohei Kadono ◽  
Tatsuya Suetsugu ◽  
Takeshi Ohtani ◽  
Toshihiko Einishi ◽  
Takashi Tarumi ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Heat Treatment ◽  
Surface Region ◽  
Borosilicate Glasses ◽  
X Ray Diffraction ◽  
X Ray ◽  
Depth Profiles ◽  
Transmission Electron ◽  
Heat Treated ◽  
Glass Heat

Copper(I) chloride and bromide nanoparticle-dispersed glasses were prepared by means of a conventional copper staining. The staining was performed by the following process: copper stain was applied on the surfaces of Cl−- or Br−-ion-containing borosilicate glasses, and the glasses were heat-treated at 510 °C for various times. Typical exciton bands observed in the absorption spectra of the glasses after the heat treatment indicated that CuCl and CuBr particles were formed in the surface region of the glasses. The average sizes of the CuCl and CuBr particles in the glasses heat-treated for 48 h were estimated at 4.8 and 2.7 nm, respectively. The nanoparticles were also characterized by x-ray diffraction and transmission electron microscopy. Depth profiles of Cu and CuBr concentration in the glass heat-treated for 48 h were measured. Copper decreased in concentration monotonously with depth, reaching up to 60 μm, while the CuBr concentration had a maximum at about 25 μm in depth.

Mechanical properties of heat-treated cellulose nanofiber-reinforced polyvinyl alcohol nanocomposite

2016 ◽  
Vol 51 (14) ◽  
pp. 1971-1977 ◽  
Author(s):  
NH Noor Mohamed ◽  
Hitoshi Takagi ◽  
Antonio N Nakagaito
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Heat Treatment ◽  
Tensile Strength ◽  
Polyvinyl Alcohol ◽  
Tensile Tests ◽  
Cellulose Nanofiber ◽  
Heat Treated ◽  
Scanning Electron ◽  
Polyvinyl Alcohol Films

The mechanical properties of cellulose nanofiber-reinforced polyvinyl alcohol composite were studied. Neat polyvinyl alcohol films, cellulose nanofiber sheets, and their nanocomposites containing cellulose nanofiber weight ratios of 5, 15, 30, 40, 45, 50 and 80 wt% were fabricated. Heat treatment by hot pressing at 180℃ was conducted on the specimens to study its effect to the mechanical properties and the results were compared with the non heat-treated specimens. Morphology of the composites was studied by scanning electron microscopy and the mechanical properties were evaluated by means of tensile tests. The results showed that increase of cellulose nanofiber content from 5 wt% to 80 wt% has increased the tensile strength of the composites up to 180 MPa, with cellulose nanofiber content higher than 40 wt% yielding higher tensile strength. The heat-treated specimens exhibited higher tensile strength compared to those of untreated specimens.

Surface Modification of Diamonds in Diamond/Al-Matrix Composite

2008 ◽  
Vol 59 ◽  
pp. 125-130 ◽  
Author(s):  
C. Edtmaier ◽  
Ludger Weber ◽  
Reza Tavangar
Keyword(s):  
Electron Microscopy ◽  
Heat Treatment ◽  
Treatment Temperature ◽  
Pressure Infiltration ◽  
Argon Gas ◽  
Diamond Particles ◽  
Heat Treated ◽  
Modified Surface ◽  
Al Matrix Composite ◽  
Al Matrix

Fe- or Mn-powders were mixed with the diamonds and the mixtures were heat treated under different gas atmospheres like hydrogen or argon gas and at varying temperatures in order to roughen the surface of the diamond particles. Subsequently the reaction layers are removed by the addition of aqueous solutions of HCl. The modified surface structure after the etching process is investigated by electron microscopy showing increased roughening of the formerly flat faces of the diamond particles with increasing heat treatment temperature. After drying the diamonds, composites were prepared by gas pressure infiltration with pure Al. For treatments in the temperature range from 750 to 850°C the thermal conductivity can be improved by up to 20 percent compared to composites based on un-treated powders.

Morphological changes of poly(tetrafluoroethylene) by heat treatment on NaCl

1993 ◽  
Vol 8 (11) ◽  
pp. 2942-2947 ◽  
Author(s):  
Sadaatsu Yamaguchi ◽  
Masaki Tsuji
Keyword(s):  
Electron Microscopy ◽  
Heat Treatment ◽  
Transmission Electron Microscopy ◽  
Morphological Changes ◽  
Dark Field ◽  
Exothermic Peak ◽  
Lateral Side ◽  
Cooling Process ◽  
Transmission Electron ◽  
Heat Treated

Fine granules of poly(tetrafluoroethylene) (PTFE) were heat-treated/annealed on NaCl near its melting temperature (Tm) and/or at a temperature (Tc) between upper and lower feet of the exothermic peak in the DSC cooling process from Tm. Morphological changes of the granules were examined in the bright- and dark-field modes by transmission electron microscopy. When the granules were heat-treated near Tm, microfibrils of 20–30 nm in width and fibrils of 70–120 nm in width came out of the granules. The microfibrils were also observed in the fibrils. The microfibrils formed by heat treatment near Tm seemed to be identified as microfibrils of 20–30 nm in width which were recognized outside the granules annealed at Tc. It is expected that such a microfibril will grow to be a band in the band structure observed on the surface of bulk PTFE. Since the 0015 dark-field images showed that the PTFE chains in such microfibrils and fibrils are set perpendicular to their fibril axis, the chains should fold back and forth repeatedly at both lateral side-surfaces of the microfibrils and fibrils.

Characterization of Ni-P and Ni-P-Al2O3 Heat Treated Layers

2017 ◽  
Vol 1143 ◽  
pp. 26-31
Author(s):  
Lucica Balint ◽  
Gina Genoveva Istrate
Keyword(s):  
Electron Microscopy ◽  
Heat Treatment ◽  
Corrosion Resistance ◽  
Composite Coatings ◽  
Treatment Temperature ◽  
Initial State ◽  
X Ray ◽  
Transmission Electron ◽  
Heat Treated ◽  
Before And After

Research has shown the relationship among hardness, usage and corrosion resistance Ni-P-Al2O3 composite coatings on steel support heat treated. The electroless strips were heat treated at 200°C, 300°C, 400°C, 500°C and 600°C. Further studies on corrosion, hardness and usage revealed changes in properties, compared to the initial state, both on the strips coated with Ni-P and the ones coated with Ni-P-Al2O3 composite. The samples have been studied before and after the heat treatment via Scanning Electron Microscopy (SEM), Transmission Electron Microscopy (TEM), Energy Dispersive X-ray Analysis (EDX) and X-Ray Diffraction (XRD). The results show that untreated Ni-P layers exhibit strong corrosion resistance, while hardness and usage increase with heat treatment temperature, with a peak at 400 °C. Using suspended particles co-deposition, led to new types of layers, some with excellent hardness and usage properties. Corrosion resistance increase with heat treatment. Coating layers can be adjusted to the desired characteristics, by selecting proper parameters for the expected specific results.

Synthesis and Characterization of Nanostructured TiO2-SnO2 Composite

2014 ◽  
Vol 975 ◽  
pp. 233-237
Author(s):  
Joelma C. S. Breve ◽  
Dayse I. dos Santos
Keyword(s):  
Electron Microscopy ◽  
Heat Treatment ◽  
Thermal Analysis ◽  
Gas Sensors ◽  
Catalytic Properties ◽  
Rutile Phase ◽  
Synthesis And Characterization ◽  
Vis Spectroscopy ◽  
Scanning Electron

Nanostructured composites based on titanium dioxide have been studied in order to improve optical and photo-catalytic properties, as well as their performance in gas sensors. In this work, titanium and tin dioxides were simultaneously synthesized by the polyol method resulting in TiO2 platelet coated with SnO2 nanoparticles as was observed by scanning electron microscopy. The thermal analysis showed that the combined synthesis promotes more easily the crystallization of the TiO2 rutile phase. The composite obtained after heat treatment at 500 °C showed to be formed of almost only rutile phases of both oxides. The optical properties analyzed by UV-Vis spectroscopy showed that the combined oxides have higher absorbance, which reinforces a model found in the literature based on the flow of photo-generated electrons to the conduction band of SnO2 delaying the recombination of charges.

High Purity Ti2AlC Powder Prepared by a Novel Method

2010 ◽  
Vol 658 ◽  
pp. 340-343 ◽  
Author(s):  
Jian Feng Zhu ◽  
Guo Quan Qi ◽  
Fen Wang ◽  
Hai Bo Yang
Keyword(s):  
Heat Treatment ◽  
Thermal Treatment ◽  
High Purity ◽  
High Energy ◽  
High Energy Milling ◽  
Heat Treated ◽  
Novel Method ◽  
Increasing Temperature ◽  
Milled Powders

Ti2AlC powders with high purity were successfully synthesized via high energy milling and heat treatment of Ti, C and Al powders. The effects of composition and thermal treatment on the formation and purity of Ti2AlC were examined in detail. The results shown a mechanically induced self-propagating reaction (MSR) was triggered to form Ti3AlC2, TiC and TiAlx during the high energy milling. When the as-milled powders were heat treated, Ti2AlC was initially formed by the reaction between TiAl and TiC. With continuously increasing temperature, Ti2AlC was also produced by the reaction between TiAl and Ti3AlC2.

scholarly journals The effect of heat treatment on thermal conductivity of paulownia wood

2019 ◽  
Vol 78 (1) ◽  
pp. 205-207
Author(s):  
Z. Pásztory ◽  
S. Fehér ◽  
Z. Börcsök
Keyword(s):  
Thermal Conductivity ◽  
Heat Treatment ◽  
Thermal Treatment ◽  
Thermal Insulation ◽  
Insulation Materials ◽  
Heat Treated ◽  
Paulownia Wood

AbstractThe thermal conductivity properties of wood of Paulownia Clones in Vitro 112 were investigated after heat treatment at temperatures of 180 °C, 200 °C and 220 °C. After the treatment, the density decreased by 5.6, 8.9, and 14.1% for the samples heat-treated at 180 °C, 200 °C and 220 °C, respectively. The decrease in the thermal conductivity was 0, 2.6 and 15.7%, respectively. The thermal conductivity of kiri wood after thermal treatment at 220 °C was 0.064 W/mK, which is almost the same as that of thermal insulation materials.

Hot Dip Aluminizing of 9Cr-1Mo Steels and their Heat Treatment

2015 ◽  
Vol 830-831 ◽  
pp. 143-146
Author(s):  
Jalpa Patel ◽  
Prashanth Huilgol ◽  
Nirav Jamnapura ◽  
K. Udaya Bhat
Keyword(s):  
Electron Microscopy ◽  
Heat Treatment ◽  
Solid Solution ◽  
Reaction Layer ◽  
Treatment Duration ◽  
Substrate Material ◽  
X Ray ◽  
Heat Treated ◽  
Heat Treatment Duration ◽  
Scanning Electron

Coupons of 9Cr-1Mo steels of type SA 387 Grade 9 class 2 were hot dip aluminized using Al bath at a temperature of 700 °C for 30 seconds. The samples were further heat treated at 750 °C for durations of 1, 3 and 5 hours, respectively. The samples were characterized using X-ray diffractometry, scanning electron microscopy and energy dispersive spectroscopy. The investigation showed that as coated samples contain an aluminum top coat, a reaction layer and substrate material. Within the reaction layer, two distinct regions corresponding to Fe2Al5 and Fe4Al13 were identified. Chromium up to 2 at% was observed. After heat treatment Al coat was not existing. Two distinct layers, corresponding to a thick Fe2Al5 and a thin FeAl were observed at shorter heat treatment duration. Under longer heat treatment durations, multiple phases, namely, Fe2Al5, FeAl, Fe3Al and solid solution of Al in Fe were observed.

Heat Treatment of Nanocrystalline Al2O3-Zr02

1996 ◽  
Vol 457 ◽  
Author(s):  
Bridget M. Smyser ◽  
Jane F. Connelly ◽  
Richard D. Sisson ◽  
Virgil Provenzano
Keyword(s):  
Electron Microscopy ◽  
Heat Treatment ◽  
Grain Size ◽  
Monoclinic Phase ◽  
Phase Distribution ◽  
Critical Size ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Heat Treated

ABSTRACTThe effects of grain size on the phase transformations in nanocrystalline ZrO2-Al2O3 have been experimentally investigated. Compositions from 10 to 50 vol% Al2O3 in ZrO2 were obtained as a hydroxide gel. The powders were then calcined at 600 °C for 17 hours and heat treated at 1100 °C for 24 and 120 hours and at 1200 °C for 2 hours. The phase distribution and grain size were determined using x-ray diffraction and transmission electron microscopy. The initial grain size after calcining was 8–17 nm. It was determined that the critical ZrO2 grain size to avoid the tetragonal to monoclinic phase transformation on cooling from 1100 °C was between 17 and 25 nm. Samples containing 50% Al2O3 maintained a grain size below the critical size for all times and temperatures. The 30% Al2O3 samples showed the same behavior in all but one heat treatment. The remainder of the samples showed significant grain growth and at least partial transformation to the monoclinic phase.

Sign in / Sign up

Export Citation Format

Share Document