scholarly journals Coal Fly Ash as Raw Material for Immobilization of Sr-Contaminated Soil by Microwave Heating: Mechanism and Performance

Crystals ◽  
2021 ◽  
Vol 12 (1) ◽  
pp. 55
Author(s):  
Yupeng Xie ◽  
Ailian Zhu ◽  
Min Chen ◽  
Bing Dai ◽  
Bin Wang ◽  
...  
Keyword(s):  
Fly Ash ◽  
Microwave Heating ◽  
Contaminated Soil ◽  
Power Plants ◽  
Coal Fly Ash ◽  
Microwave Sintering ◽  
Phase Evolution ◽  
Raw Material ◽  
Elemental Distribution ◽  
And Performance

In this work, coal fly ash, hereinafter CFA is proposed to work as raw material for immobilization of Sr-contaminated soil by microwave sintering in the path towards resource utilization of solid waste. The immobilization mechanism and performance was systemically investigated through phase evolution, microstructure, elemental distribution, and physical properties. The results shown that the Sr could be incorporated into feldspar strontian (SrAl2Si2O8) at 1300 °C for 30 min. Moreover, the maximum solid solubility of SrSO4 was more than 30 wt.%. The Sr was homogeneously distributed in the sintered matrices without substantial enrichment. The sintered matrix exhibited high density (2.53 g/cm3). Thus, microwave heating coupled with CFA could provide a new method for immobilization of Sr-contaminated soil in case of the spent nuclear reprocessing cycle in nuclear power plants or a nuclear accident emergency.

scholarly journals Rare earth elements in deposited hard coal fly ash in Poland

2021 ◽  
Vol 278 ◽  
pp. 01016
Author(s):  
Justyna Woźniak ◽  
Marcel Gurdziel
Keyword(s):  
Rare Earth ◽  
Fly Ash ◽  
Rare Earth Elements ◽  
Power Plants ◽  
Coal Fly Ash ◽  
Raw Material ◽  
Hard Coal ◽  
Central Statistical ◽  
Central Statistical Office ◽  
Modern Technologies

Rare Earth Elements (REEs), due to their unique properties, are nowadays a desirable raw material, especially in the development of modern technologies. This paper describes a 4-step research methodology for the task of identifying the potential for REE recovery in landfilled fly ash. A literature analysis was performed on their significance, occurrence in both primary and secondary deposits. Opportunities for REE recovery from coal fly ash in conventional power plants were identified and selected technologies were described. Poland, as a country whose energy sector is to a large extent based on coal, has a potential in this respect. Taking into account studies of the Polish Central Statistical Office (GUS) and forecasts of the Polish energy policy, the article determines the approximate value of REE in the waste stream from coal-fired power plants burning hard coal.

scholarly journals Extraction of Al-Si master alloy and alumina from coal fly ash

2017 ◽  
Vol 53 (2) ◽  
pp. 155-162 ◽  
Author(s):  
A. Liu ◽  
Z. Shi ◽  
K. Xie ◽  
X. Hu ◽  
B. Gao ◽  
...  
Keyword(s):  
Fly Ash ◽  
Master Alloy ◽  
Power Plants ◽  
Coal Fly Ash ◽  
Raw Material ◽  
Aluminothermic Reduction ◽  
Chemical Compositions ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray

Coal fly ash from coal power plants is a potential raw material for the production of alumina. An objective aluminothermic reduction method for the preparation of Al-Si master alloy and alumina from coal fly ash was investigated. The kinetic analysis using non-isothermal differential scanning calorimetry indicated that the reduction of Al6Si2O13, Fe2O3, and TiO2 by aluminum in coal fly ash occurs at 1618 K, 1681 K, and 1754 K, respectively. Moreover, the influence of reaction temperature on product composition was studied. The phases and morphologies of the products obtained by the aluminothermic reduction of coal fly ash at 1373-1773 K were analyzed by X-ray diffraction, scanning electron microscopy, and energy-dispersive spectroscopy, respectively. The results from X-ray diffraction show that no oxide reduction has taken place at 1373 K and 1473K, the compositions of the product obtained by aluminothermic reduction of fly ash at 1573K- 1673 K are Al2O3, mullite, Al and Si, while the compositions of the product at 1773 K are Al2O3, Al, and Si. In addition, the chemical compositions of Al-Si alloy obtained at 1773 K are 86.81 wt% Al and 13.19 wt% Si.

UTILIZATION OF COAL FLY ASH FROM POWER PLANTS - I. ASH CHARACTERIZATION

2008 ◽  
Vol 7 (3) ◽  
pp. 289-293 ◽  
Author(s):  
Maria Harja ◽  
Marinela Barbuta ◽  
Lacramioara Rusu ◽  
Nicolae Apostolescu
Keyword(s):  
Fly Ash ◽  
Power Plants ◽  
Coal Fly Ash

scholarly journals Preparation of Synthetic Zeolites from Coal Fly Ash by Hydrothermal Synthesis

Materials ◽  
2021 ◽  
Vol 14 (5) ◽  
pp. 1267
Author(s):  
David Längauer ◽  
Vladimír Čablík ◽  
Slavomír Hredzák ◽  
Anton Zubrik ◽  
Marek Matik ◽  
...  
Keyword(s):  
Fly Ash ◽  
Coal Combustion ◽  
Power Plants ◽  
Coal Fly Ash ◽  
Thermal Power ◽  
Product Analysis ◽  
Coal Combustion Products ◽  
X Ray ◽  
Wide Range ◽  
Silica Alumina

Large amounts of coal combustion products (as solid products of thermal power plants) with different chemical and physical properties cause serious environmental problems. Even though coal fly ash is a coal combustion product, it has a wide range of applications (e.g., in construction, metallurgy, chemical production, reclamation etc.). One of its potential uses is in zeolitization to obtain a higher added value of the product. The aim of this paper is to produce a material with sufficient textural properties used, for example, for environmental purposes (an adsorbent) and/or storage material. In practice, the coal fly ash (No. 1 and No. 2) from Czech power plants was firstly characterized in detail (X-ray diffraction (XRD), X-ray fluorescence (XRF), scanning electron microscopy with energy dispersive X-ray analysis (SEM-EDX), particle size measurement, and textural analysis), and then it was hydrothermally treated to synthetize zeolites. Different concentrations of NaOH, LiCl, Al2O3, and aqueous glass; different temperature effects (90–120 °C); and different process lengths (6–48 h) were studied. Furthermore, most of the experiments were supplemented with a crystallization phase that was run for 16 h at 50 °C. After qualitative product analysis (SEM-EDX, XRD, and textural analytics), quantitative XRD evaluation with an internal standard was used for zeolitization process evaluation. Sodalite (SOD), phillipsite (PHI), chabazite (CHA), faujasite-Na (FAU-Na), and faujasite-Ca (FAU-Ca) were obtained as the zeolite phases. The content of these zeolite phases ranged from 2.09 to 43.79%. The best conditions for the zeolite phase formation were as follows: 4 M NaOH, 4 mL 10% LiCl, liquid/solid ratio of 30:1, silica/alumina ratio change from 2:1 to 1:1, temperature of 120 °C, process time of 24 h, and a crystallization phase for 16 h at 50 °C.

scholarly journals Recovery of Cenospheres and Fine Fraction from Coal Fly Ash by a Novel Dry Separation Method

Energies ◽  
2020 ◽  
Vol 13 (14) ◽  
pp. 3576
Author(s):  
Jan Wrona ◽  
Witold Żukowski ◽  
Dariusz Bradło ◽  
Piotr Czupryński
Keyword(s):  
Fly Ash ◽  
Coal Fly Ash ◽  
Fine Fraction ◽  
Free Fall ◽  
Raw Material ◽  
Fluidised Bed ◽  
Air Chamber ◽  
Pneumatic Separation ◽  
Bed Separation ◽  
Separation Product

Aluminosilicate microspheres are a valuable fraction of coal fly ash with diverse applications due to their low density. Currently, there is no efficient and ecologically rational method of cenosphere recovery from fly ash. A combination of dry methods for the recovery of both fine ash particles and aluminosilicate microspheres from coal fly ash is presented. It is comprised of fluidised bed separation followed by screening and pneumatic separation in a free-fall air chamber. Fluidised bed separation was assisted by a mechanical activator to prevent agglomeration. This step reduced the portion of material that required further treatment by 52–55 wt.%, with the recovery of microspheres exceeding 97%. Then, the concentrates were individually subjected to pneumatic separation. The final separation product for the fly ash containing 0.64 wt.% cenospheres was a cenosphere concentrate that constituted about 17 wt.% of the initial fly ash. The recovery of cenospheres was around 81%. Usage of a combination of dry methods allowed for maintaining almost 83 wt.% of the raw material in its dry form. Furthermore, the produced fly ash grain fractions could be used for different industrial purposes.

Characterization of Coal Fly Ash, Bottom Ash and their Possibilities as Catalysts for Biodiesel Production

2021 ◽  
Vol 904 ◽  
pp. 413-418
Author(s):  
Wilasinee Kingkam ◽  
Sasikarn Nuchdang ◽  
Dussadee Rattanaphra
Keyword(s):  
Fly Ash ◽  
Palm Oil ◽  
Power Plants ◽  
Coal Fly Ash ◽  
Bottom Ash ◽  
Biodiesel Production ◽  
Catalyst Loading ◽  
Free Lime ◽  
Operation Conditions ◽  
Class C

Coal fly ash (CFA) and bottom ash (BA) obtained from coal fired power plants in Thailand and local supplier were characterized using XRF, XRD and N2 adsorption-desorption techniques. Their possibilities for conversion of palm oil into biodiesel were investigated. Selected CFA was also modified with lanthanum (La) at different La loading and the influence of La loading on biodiesel conversion was evaluated. The resulted showed that the Class C CFA as contained large amount of CaO (free lime) could catalyze the transesterification to achieve the highest FAME content of 89% under the operation conditions; the reaction temperature of 200 °C, the reaction pressure of 39 bars, the catalyst loading of 5 wt% of oil, the molar of oil to methanol of 1:30 and the stirring speed of 600 rpm for 5 h. The addition of La on the Class C CFA had a negative effect on conversion of palm oil. The FAME content decreased gradually from 89 to 62% with increasing La loading from 0 to 1 wt%.

Total reflection X-ray fluorescence analysis of fly ash from Bulgarian coal-fired power plants

2015 ◽  
Vol 69 (5) ◽  
Author(s):  
Albena K. Detcheva ◽  
Svilen E. Mitsiev ◽  
Paunka S. Vassileva ◽  
Juri H. Jordanov ◽  
Metody G. Karadjov ◽  
...  
Keyword(s):  
Fly Ash ◽  
Power Plants ◽  
Coal Fly Ash ◽  
Internal Standard ◽  
Fluorescence Analysis ◽  
Total Reflection ◽  
X Ray

AbstractThe contents of Cl, Ca, K, Ti, V, Cr, Mn, Fe, Ni, Cu, Zn, As, Se, Rb, Sr, Ba and Pb in raw coal fly ash from five Bulgarian power plants were determined by total reflection X-ray fluorescence (TXRF), using gallium as the internal standard. The samples were analysed as in slurry form in Triton

Utilization of Fly Ash in the Synthesis of Refractory Forsterite-Spinel Ceramics

2021 ◽  
Vol 321 ◽  
pp. 131-140
Author(s):  
Martin Nguyen ◽  
Radomír Sokolař
Keyword(s):  
Thermal Expansion ◽  
Fly Ash ◽  
Thermal Shock ◽  
Thermal Shock Resistance ◽  
Power Plants ◽  
Linear Thermal Expansion ◽  
Aluminium Oxide ◽  
Raw Material ◽  
Modulus Of Rupture ◽  
Shock Resistance

Forsterite refractory ceramics is utilized in the metallurgical and cement industries as a lining of metallurgical furnaces and rotary kilns for its high refractoriness up to 1850°C and refractoriness under load above 1600°C. Another significant property of forsterite is its coefficient of linear thermal expansion utilized in the electrotechnical industry for ceramic-metal joints. Addition of aluminium oxide into the raw material mixture results in creation of magnesium-alumina spinel (MgO·Al2O3) which improves sintering, thermal shock resistance and mechanical properties in comparison with pure forsterite ceramics. Inexpensive source of aluminium oxide is fly ash. Utilization of fly ash, secondary energetic product of coal-burning power plants, is important for the environment and sustainable development. This paper evaluated properties of fly ash-based forsterite-spinel ceramics in comparison with alumina-based forsterite-spinel ceramics. Forsterite-spinel ceramics was synthesized from olivine, calcined magnesite and fly ash/alumina powders. XRD analysis was used to determine mineralogical composition, thermal analyses were used to determine the behaviour during firing and scanning electron microscopy to determine the morphology of crystal phases. Refractoriness of pyrometric cones, refractoriness under load, thermal shock resistance, coefficient of linear thermal expansion, water absorption, porosity and modulus of rupture were also determined on fired test samples.

Treatment of Coal Fly Ash And Its Environmentally Friendly Use In Rubber And Plastic Industry

2021 ◽  
Author(s):  
Zawar Hussain ◽  
Gao Lizhen ◽  
Wang Haitao ◽  
Tehreem Ayaz ◽  
Amir Zeb Khan
Keyword(s):  
Fly Ash ◽  
Calcium Carbonate ◽  
Barium Sulfate ◽  
Power Plants ◽  
Coal Fly Ash ◽  
Conveyor Belt ◽  
Plastic Waste ◽  
Talcum Powder ◽  
Coal Power Plants ◽  
Coal Power

Abstract Coal power plants are the major contributor of electricity but these power plants are also producing waste in the form of coal fly ash (CFA). However, it can cause high risk of environmental pollution and pulmonary diseases in humans. Plastic waste is also a problematic waste for many countries in terms of its reuse and recycling. Therefore, this study aims to reuse the waste product (CFA) of coal power plants in rubber conveyer belt instead of calcium carbonate or talcum powder and in recycling of plastic propylene as bonding filler material instead of barium sulfate to increase the durability of plastic products and reduce cost, CFA waste and plastic waste. For this purpose, CFA was treated by different pulverization techniques for the production of conveyor belt. The study found that the most favorable technique was shear based pulverization technique. Application of CFA with rubber was compared with two different chemicals (calcium carbonate and talcum powder) and found that the elongation at break of conveyor belt was 35% increased and abrasion volume was 64% reduced by using treated CFA. Furthermore, CFA was used in molten mass of plastic instead of barium sulfate and the results showed that the use of CFA has improved the dimensional stability of plastic material reducing the cost per ton by 2410 CNY. The study concluded that the performance was increased by applying CFA with a reduction in price as compared to other chemicals.

Sign in / Sign up

Export Citation Format

Share Document