scholarly journals Wearable Flexible Phototherapy Device for Knee Osteoarthritis

Electronics ◽  
2021 ◽  
Vol 10 (16) ◽  
pp. 1891
Author(s):  
Kun Liu ◽  
Hongda Chen ◽  
Yuguang Wang ◽  
Mengqi Wang ◽  
Jun Tang

Knee osteoarthritis (OA) is a highly prevalent and disabling disease that causes pain and gradual degeneration of the articular cartilage. Phototherapy is a new physiotherapy treatment, more effective and stable than other non-pharmacologic management. Conventional phototherapy devices typically suffer from unintelligent and bulky equipment, while existing phototherapy methods require maintain a certain phototherapy distance. Here, we introduce a wearable flexible phototherapy device worn on a knee for osteoarthritis, incorporating a phototherapy adhesive patch and a control box. The phototherapy adhesive patch is capable of softly laminating onto the curved surfaces of the knee skin to increase the effects of phototherapy. We describe the LED array, constant current drive module, key control module, and power supply module that serve as the foundations for the control box. The weight of the device is only 101.8 g. The irradiance of the device can be adjusted linearly and irradiance of the designed phototherapy device based on LED can reach 13 mW/cm2. The maximum temperature of the surface of the light source is 31.2 °C. The device proposed in this work exhibits satisfactory stability, promising a potential in phototherapy.

2014 ◽  
Vol 687-691 ◽  
pp. 3235-3238
Author(s):  
Xiao Min Han

This design uses ATMEG8L as the master chip, real-time detection the state of the main power supply DC voltage, by controlling the MOSFET has the ability to quickly turn off the main power and backup power to achieve seamless switching, switching time of less than 1ms; by controlling the MOSFET with the fast turn-off capability to achieve the main power supply and backup power seamless switching, switching time of less than 1ms; Valley-fill PFC circuit is used in the main power supply to ensure the power factor > 0.9, DC-DC buck circuit is composed of LM2576T - ADJ, when great fluctuations in input voltage, output voltage 8 v is very stable, error < 1%, DC-DC boost circuit composed by LM2577T-ADJ, the battery voltage decay process, to achieve a stable output voltage of 8V, LED constant current drive circuit composed by PT4115, adjustable output current and high precision, and then adjust the brightness of LED. Master control chip, through detecting the change of photosensitive resistance, control the duty ratio of PWM wave, In order to achieve LED brightness can be adjusted automatically with ambient light, Protection of the power transformer is perfect, efficiency > 85%.


2013 ◽  
Vol 709 ◽  
pp. 408-412
Author(s):  
Yan Ling Zhao ◽  
Rong Xing Liu

Abstract. A mid-frequency magnetron sputtering (MFMS) power supply based on TL494 and MCU was introduced. A Buck Chopper and full bridge inverter were applied to the main circuit. The PWM controller TL494 was used in the Buck voltage-regulation control circuit to realize closed loop control. The drive signal of the IGBT in full bridge inverter was based on precise digital pulse width modulator (DPWM) signal produced by the MCU M30290. The DPWM can be set by potentiometer so the power supply can output the square wave with adjustable frequency and duty cycle. The power supply was operated in constant current mode. For micro or strong arcing of the target, different safeguards were adopted by the control circuit. At last, the system test and experimental results show that the stability, reliability and tuning range of the MFMS power supply can meet the requirements of the magnetron sputtering coating.


2021 ◽  
Vol 92 (11) ◽  
pp. 114706
Author(s):  
Geethanjali Pandeswara ◽  
Naresh Pasula ◽  
Geshma Kumari R

2020 ◽  
Vol 21 (4) ◽  
pp. 604-614
Author(s):  
Yu-jia Zang ◽  
Yan-hu Chen ◽  
Can-jun Yang ◽  
De-jun Li ◽  
Ze-jian Chen ◽  
...  

Sign in / Sign up

Export Citation Format

Share Document