scholarly journals Scaling Method of the Rotating Blade of a Wind Turbine for a Rime Ice Wind Tunnel Test

Energies ◽  
2019 ◽  
Vol 12 (4) ◽  
pp. 627 ◽  
Author(s):  
Yan Li ◽  
Ce Sun ◽  
Yu Jiang ◽  
Fang Feng
Keyword(s):  
Heat Transfer ◽  
Wind Tunnel ◽  
Large Scale ◽  
Wind Tunnel Test ◽  
Full Scale ◽  
Similar Degree ◽  
Transfer Model ◽  
Ice Accretion ◽  
Water Droplets ◽  
Scaling Method

In order to research the law of rime ice accretion on different scaling blades surface, a new rime ice scaling method was proposed in this research. According to previous research, there are three kinds of ice types on blade surfaces: rime ice, glaze ice and mixed ice. Under the condition of rime ice, both the freezing fraction and the coefficient of heat transfer between super-cold water droplets and blade are 100%. The heat transfer model of rime ice is simpler than that of glaze ice and mixed ice. In this research, the scaling parameters including flow field, water droplets, temperature, pressure and rotating parameters were defined. The Weber number (We) based on water film thickness as an important parameter was applied in this study. The rotating parameters including rotating speed and radius had been added into the icing scaling method. To verify the effectiveness of the new rime ice scaling method, icing wind tunnel tests were carried out. The NACA0018 airfoil was used for the test blade. Two kinds of scale chord blades were selected, the chord of full-scale blade was 200 mm and of subscale blade was 100 mm. The test temperature was −15 °C. The ice accretion on different scale blades surface were captured by high-speed camera and the icing shapes of different scaling blades were obtained. To quantitatively analyze the similar degree of icing shapes on different scale blades, an evaluation method which included similar degree (Sim) was established based on the typical characteristic parameters proposed by previous research. The results show that the icing shapes of subscale blades are similar to that of full-scale blades. The similar degree is between 75.22% and 93.01%. The icing wind tunnel test indicates that the new rime ice scaling method is an effective method to study the rime ice of large scale rotating blades. This study can be used as a reference for research on anti-icing and de-icing technologies for large-scale HAWTs (Horizontal Axis Wind Turbines).

scholarly journals Heat Transfer in Rotating Serpentine Passages With Trips Normal to the Flow

1992 ◽  
Vol 114 (4) ◽  
pp. 847-857 ◽  
Author(s):  
J. H. Wagner ◽  
B. V. Johnson ◽  
R. A. Graziani ◽  
F. C. Yeh
Keyword(s):  
Heat Transfer ◽  
Turbine Blade ◽  
Large Scale ◽  
Flow Direction ◽  
Operating Conditions ◽  
Transfer Model ◽  
Transfer Coefficients ◽  
Flow Equations ◽  
Turbine Blade Cooling ◽  
Heat Transfer Coefficients

Experiments were conducted to determine the effects of buoyancy and Coriolis forces on heat transfer in turbine blade internal coolant passages. The experiments were conducted with a large-scale, multipass, heat transfer model with both radially inward and outward flow. Trip strips on the leading and trailing surfaces of the radial coolant passages were used to produce the rough walls. An analysis of the governing flow equations showed that four parameters influence the heat transfer in rotating passages: coolant-to-wall temperature ratio, Rossby number, Reynolds number, and radius-to-passage hydraulic diameter ratio. The first three of these four parameters were varied over ranges that are typical of advanced gas turbine engine operating conditions. Results were correlated and compared to previous results from stationary and rotating similar models with trip strips. The heat transfer coefficients on surfaces, where the heat transfer increased with rotation and buoyancy, varied by as much as a factor of four. Maximum values of the heat transfer coefficients with high rotation were only slightly above the highest levels obtained with the smooth wall model. The heat transfer coefficients on surfaces where the heat transfer decreased with rotation, varied by as much as a factor of three due to rotation and buoyancy. It was concluded that both Coriolis and buoyancy effects must be considered in turbine blade cooling designs with trip strips and that the effects of rotation were markedly different depending upon the flow direction.

Study on Effective Radial Thermal Conductivity of Gas Flow through a Methanol Reactor

2015 ◽  
Vol 13 (1) ◽  
pp. 103-112 ◽  
Author(s):  
Kun Lei ◽  
Hongfang Ma ◽  
Haitao Zhang ◽  
Weiyong Ying ◽  
Dingye Fang
Keyword(s):  
Heat Transfer ◽  
Thermal Conductivity ◽  
Reynolds Number ◽  
Temperature Distribution ◽  
Large Scale ◽  
Gas Flow ◽  
Fixed Bed ◽  
Heat Transfer Model ◽  
Transfer Model ◽  
Particle Reynolds Number

Abstract The heat conduction performance of the methanol synthesis reactor is significant for the development of large-scale methanol production. The present work has measured the temperature distribution in the fixed bed at air volumetric flow rate 2.4–7 m3 · h−1, inlet air temperature 160–200°C and heating tube temperature 210–270°C. The effective radial thermal conductivity and effective wall heat transfer coefficient were derived based on the steady-state measurements and the two-dimensional heat transfer model. A correlation was proposed based on the experimental data, which related well the Nusselt number and the effective radial thermal conductivity to the particle Reynolds number ranging from 59.2 to 175.8. The heat transfer model combined with the correlation was used to calculate the temperature profiles. A comparison with the predicated temperature and the measurements was illustrated and the results showed that the predication agreed very well with the experimental results. All the absolute values of the relative errors were less than 10%, and the model was verified by experiments. Comparing the correlations of both this work with previously published showed that there are considerable discrepancies among them due to different experimental conditions. The influence of the particle Reynolds number on the temperature distribution inside the bed was also discussed and it was shown that improving particle Reynolds number contributed to enhance heat transfer in the fixed bed.

scholarly journals Heat Transfer in Rotating Serpentine Passages With Trips Normal to the Flow

1991 ◽  
Author(s):  
J. H. Wagner ◽  
B. V. Johnson ◽  
R. A. Graziani ◽  
F. C. Yeh
Keyword(s):  
Heat Transfer ◽  
Turbine Blade ◽  
Large Scale ◽  
Flow Direction ◽  
Operating Conditions ◽  
Transfer Model ◽  
Transfer Coefficients ◽  
Flow Equations ◽  
Turbine Blade Cooling ◽  
Heat Transfer Coefficients

Experiments were conducted to determine the effects of buoyancy and Coriolis forces on heat transfer in turbine blade internal coolant passages. The experiments were conducted with a large scale, multi–pass, heat transfer model with both radially inward and outward flow. Trip strips on the leading and trailing surfaces of the radial coolant passages were used to produce the rough walls. An analysis of the governing flow equations showed that four parameters influence the heat transfer in rotating passages: coolant–to–wall temperature ratio, Rossby number, Reynolds number and radius–to–passage hydraulic diameter ratio. The first three of these four parameters were varied over ranges which are typical of advanced gas turbine engine operating conditions. Results were correlated and compared to previous results from stationary and rotating similar models with trip strips. The heat transfer coefficients on surfaces, where the heat transfer increased with rotation and buoyancy, varied by as much as a factor of four. Maximum values of the heat transfer coefficients with high rotation were only slightly above the highest levels obtained with the smooth wall model. The heat transfer coefficients on surfaces, where the heat transfer decreased with rotation, varied by as much as a factor of three due to rotation and buoyancy. It was concluded that both Coriolis and buoyancy effects must be considered in turbine blade cooling designs with trip strips and that the effects of rotation were markedly different depending upon the flow direction.

scholarly journals Heat Transfer in Rotating Serpentine Passages With Trips Skewed to the Flow

1994 ◽  
Vol 116 (1) ◽  
pp. 113-123 ◽  
Author(s):  
B. V. Johnson ◽  
J. H. Wagner ◽  
G. D. Steuber ◽  
F. C. Yeh
Keyword(s):  
Heat Transfer ◽  
Turbine Blade ◽  
Large Scale ◽  
Flow Direction ◽  
Operating Conditions ◽  
Transfer Model ◽  
Transfer Coefficients ◽  
Flow Equations ◽  
Turbine Blade Cooling ◽  
Heat Transfer Coefficients

Experiments were conducted to determine the effects of buoyancy and Coriolis forces on heat transfer in turbine blade internal coolant passages. The experiments were conducted with a large-scale, multipass, heat transfer model with both radially inward and outward flow. Trip strips, skewed at 45 deg to the flow direction, were machined on the leading and trailing surfaces of the radial coolant passages. An analysis of the governing flow equations showed that four parameters influence the heat transfer in rotating passages: coolant-to-wall temperature ratio, rotation number, Reynolds number, and radius-to-passage hydraulic diameter ratio. The first three of these four parameters were varied over ranges that are typical of advanced gas turbine engine operating conditions. Results were correlated and compared to previous results from similar stationary and rotating models with smooth walls and with trip strips normal to the flow direction. The heat transfer coefficients on surfaces, where the heat transfer decreased with rotation and buoyancy, decreased to as low as 40 percent of the value without rotation. However, the maximum values of the heat transfer coefficients with high rotation were only slightly above the highest levels previously obtained with the smooth wall model. It was concluded that (1) both Coriolis and buoyancy effects must be considered in turbine blade cooling designs with trip strips, (2) the effects of rotation are markedly different depending upon the flow direction, and (3) the heat transfer with skewed trip strips is less sensitive to buoyancy than the heat transfer in models with either smooth walls or normal trips. Therefore, skewed trip strips rather than normal trip strips are recommended and geometry-specific tests will be required for accurate design information.

scholarly journals Aerodynamic study of a suspension bridge deck by CFD simulations, wind tunnel tests and full-scale observations

2021 ◽  
Vol 1201 (1) ◽  
pp. 012007
Author(s):  
I. Kusano ◽  
E. Cheynet ◽  
J. B. Jakobsen ◽  
J. Snæbjörnsson
Keyword(s):  
Wind Tunnel ◽  
Wind Tunnel Test ◽  
Suspension Bridge ◽  
Aerodynamic Characteristics ◽  
Full Scale ◽  
Navier Stokes ◽  
Cfd Simulations ◽  
Wind Tunnel Tests ◽  
Long Span Bridges ◽  
Wide Range

Abstract Assessing the aerodynamic characteristics of long-span bridges is fundamental for their design. Depending on the terrain complexity and local wind conditions, episodes of large angles of attack (AoA) of 15° may be observed. However, such large AoAs ( above 10°) are often overlooked in the design process. This paper studies the aerodynamics properties of a flow around a single-box girder for a wide range of AoAs, from –20° to 20°, using numerical simulations. The simulations are based on a 2D unsteady Reynolds-averaged Navier–Stokes (URANS) approach using the k − ω SST turbulence model with a Reynolds number of 1.6 × 105. Numerically obtained aerodynamic static coefficients were compared to wind tunnel test data. The CFD results were generally in good agreement with the wind tunnel tests, especially for small AoAs and positive AoAs. More discrepancies were observed for large negative AoA, likely due to the limitation of modelling 3D railings with 2D simulations. The simulated velocity deficit downstream of the deck was consistent with the one measured in full-scale using short-range Doppler wind lidar instruments. Finally, the Strouhal number from the CFD simulations were in agreement with the value obtained from the full-scale data.

scholarly journals A Parametric Design Method for Hybrid Airfoils for Icing Wind Tunnel Test

2021 ◽  
Vol 2021 ◽  
pp. 1-18
Author(s):  
Zhao Li ◽  
Guang-jun Yang ◽  
Xiao-yan Tong ◽  
Feng Jiang
Keyword(s):  
Flow Field ◽  
Parametric Design ◽  
Design Method ◽  
Pressure Coefficient ◽  
Wind Tunnel Test ◽  
Leading Edge ◽  
Full Scale ◽  
Navier Stokes ◽  
Ice Accretion ◽  
Multiple Control

The size of aircraft models that can be tested in icing wind tunnels is limited by the dimensions of the facilities in present; it is an effective method to replace the large model with a hybrid airfoil to carry out the experiment. A design method of multiple control points for hybrid airfoil based on the similarity of flow field in the leading edge of airfoil is proposed. Aiming at generating the full-scale flow field and ice accretion on the leading edge, multiobjective genetic optimization algorithm is used to design the hybrid airfoil under different conditions by combining the airfoil parameterization and solution of spatial constraint. Pressure tests of hybrid airfoils are carried out and compared with the leading edge pressure of the corresponding full-scale airfoils. The design and experimental results show that the pressure coefficient deviation between the hybrid airfoils designed and the corresponding full-scale airfoil in the 15% chord length range of the leading edge is within 4%. Finally, the vortex distribution and ice accretion process of the two airfoils were simulated by the unsteady Reynolds-averaged-Navier–Stokes (URANS) equations and multistep ice numerical method; it is shown that the hybrid airfoil can provide the same vortex distribution and ice accretion with the full-scale airfoil.

Feasibility investigation of large-scale model suspended by cable-driven parallel robot in hypersonic wind tunnel test

2016 ◽  
Vol 231 (13) ◽  
pp. 2375-2383 ◽  
Author(s):  
Xiaoguang Wang ◽  
Miaojiao Peng ◽  
Zhenghong Hu ◽  
Yueshi Chen ◽  
Qi Lin
Keyword(s):  
Wind Tunnel ◽  
Large Scale ◽  
Cfd Simulation ◽  
Aerodynamic Force ◽  
Wind Tunnel Test ◽  
Special Kind ◽  
Parallel Robot ◽  
Scale Model ◽  
Hypersonic Wind Tunnel ◽  
Large Scale Model

Cable-driven parallel robot is a special kind of robot, which is actuated by cables. It is already applied in the low speed wind tunnel to get aerodynamic measurement of aircraft model, and the aircraft pose could be adjusted by changing the cable length. Whether it can be used in hypersonic wind tunnel still needs further discussion. This paper presents the dynamics and aerodynamics analysis of a large-scale model supported by 6-DOF cable-driven parallel robot to investigate the feasibility of this special kind of suspension system in hypersonic wind tunnel. The description of this setup with a X-51A-like model is given, and then based on the system dynamic equations, aerodynamic force and stiffness matrix are derived. In the simulation, properties of dynamics and aerodynamics are mainly concerned. A typical shock tunnel with flow duration of about 100 milliseconds is taken as an example, and results show that the system is stable enough to meet the fundamental static wind tunnel test. From the cable tension variation under impact load and the sensitivity analysis, it is likely accessible to derive the aerodynamic forces. Compared with the sting suspension method, cable-driven parallel robot has the priority of higher inherent frequency and more flexible degrees. The interference to the flow field induced by cables is also preliminarily proved to be small by the CFD simulation, which can be acceptable and corrected. Researches conducted show the feasibility of cable-driven parallel robot’s application in hypersonic wind tunnel.

Fluidic actuators for separation control at the engine/wing junction

2017 ◽  
Vol 89 (5) ◽  
pp. 709-718 ◽  
Author(s):  
Philipp Schloesser ◽  
Michael Meyer ◽  
Martin Schueller ◽  
Perez Weigel ◽  
Matthias Bauer
Keyword(s):  
Wind Tunnel ◽  
Flow Control ◽  
Flow Separation ◽  
Mass Flux ◽  
Large Scale ◽  
Active Flow Control ◽  
Wind Tunnel Test ◽  
Local Flow ◽  
Content Type ◽  
Active Flow

Purpose The area behind the engine/wing junction of conventional civil aircraft configurations with underwing-mounted turbofans is susceptible to local flow separation at high angles of attack, which potentially impacts maximum lift performance of the aircraft. This paper aims to present the design, testing and optimization of two distinct systems of fluidic actuation dedicated to reduce separation at the engine/wing junction. Design/methodology/approach Active flow control applied at the unprotected leading edge inboard of the engine pylon has shown considerable potential to alleviate or even eliminate local flow separation, and consequently regain maximum lift performance. Two actuator systems, pulsed jet actuators with and without net mass flux, are tested and optimized with respect to an upcoming large-scale wind tunnel test to assess the effect of active flow control on the flow behavior. The requirements and parameters of the flow control hardware are set by numerical simulations of project partners. Findings The results of ground test show that full modulation of the jets of the non-zero mass flux actuator is achieved. In addition, it could be shown that the required parameters can be satisfied at design mass flow, and that pressure levels are within bounds. Furthermore, a new generation of zero-net mass flux actuators with improved performance is presented and described. This flow control system includes the actuator devices, their integration, as well as the drive and control electronics system that is used to drive groups of actuators. Originality/value The originality is given by the application of the two flow control systems in a scheduled large-scale wind tunnel test.

Sign in / Sign up

Export Citation Format

Share Document