scholarly journals Perovskite Solar Cell with Added Gold/Silver Nanoparticles: Enhanced Optical and Electrical Characteristics

Energies ◽  
2020 ◽  
Vol 13 (15) ◽  
pp. 3854
Author(s):  
Ali Hajjiah ◽  
Hussein Badran ◽  
Ishac Kandas ◽  
Nader Shehata
Keyword(s):  
Solar Cell ◽  
Short Circuit ◽  
Perovskite Solar Cells ◽  
Short Circuit Current ◽  
Perovskite Solar Cell ◽  
Open Circuit ◽  
Electrical Characteristics ◽  
Ag Nps ◽  
Resonance Frequencies ◽  
Gold Silver

Different perovskite materials, such as methylammonium lead triiodide MAPbI3, exhibit many outstanding and desirable properties in solar energy harvesting. In this paper, the enhancement of perovskite solar cells’ both optical and electrical characteristics through adding either gold (Au) or silver (Ag) nanoparticles (NPs) using different simulations was studied. The used plasmonic nanoparticles were found to be able to compensate for the low absorption of MAPbI3 in the visible with optical coupling resonance frequencies close to that spectrum. Optimal diameters of Au and Ag NPs were found and simulated, and their impact on different parameters such as transmission, absorption, reflection, external quantum efficiency (EQE), open circuit voltage, short-circuit current density, fill factor, and most importantly, efficiency of the perovskite solar cell, have been investigated.

scholarly journals Simulation of a perovskite sandwich solar cell with the p-CZTS / p-CH3NH3PbCI3 / p-CZTS absorber layers

2021 ◽  
Vol 877 (1) ◽  
pp. 012001
Author(s):  
Marwah S Mahmood ◽  
N K Hassan
Keyword(s):  
Solar Cell ◽  
Conversion Efficiency ◽  
Current Density ◽  
Short Circuit ◽  
Perovskite Solar Cells ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Open Circuit ◽  
Current Voltage ◽  
Cell Capacitance

Abstract Perovskite solar cells attract the attention because of their unique properties in photovoltaic cells. Numerical simulation to the structure of Perovskite on p-CZTS/p-CH3NH3PbCI3/p-CZTS absorber layers is performed by using a program solar cell capacitance simulator (SCAPS-1D), with changing absorber layer thickness. The effect of thickness p-CZTS/p-CH3NH3PbCI3/p-CZTS, layers at (3.2μm, 1.8 μm, 1.1 μm) respectively are studied. The obtained results are short circuit current density (Jsc ), open circuit voltage (V oc), fill factor (F. F) and power conversion efficiency (PCE) equal to (28 mA/cm2, 0.83 v, 60.58 % and 14.25 %) respectively at 1.1 μm thickness. Our findings revealed that the dependence of current - voltage characteristics on the thickness of the absorbing layers, an increase in the amount of short circuit current density with an increase in the thickness of the absorption layers and thus led to an increase in the conversion efficiency and improvement of the cell by increasing the thickness of the absorption layers.

Modeling of Abnormal Hysteresis in CsPbBr3 based Perovskite Solar Cells

2021 ◽  
Vol 34 (1) ◽  
pp. 01-08
Author(s):  
B GopalKrishna ◽  
Sanjay Tiwari
Keyword(s):  
Solar Cells ◽  
Solar Cell ◽  
Simulation Study ◽  
Open Circuit Voltage ◽  
Layer Structure ◽  
Short Circuit ◽  
Perovskite Solar Cells ◽  
Perovskite Solar Cell ◽  
Open Circuit ◽  
Perovskite Layer

Perovskite solar cells are emerging photovoltaic devices with PCE of above 25%. Perovskite are suitable light absorber materials in solar cells with excellent properties like appropriate band gap energy, long carrier lifetime and diffusion length, and high extinction coefficient. Simulation study is an important technique to understand working mechanisms of perovskites solar cells. The study would help develop efficient, stable PSCs experimentally. In this study, modeling of perovskite solar cell was carried out through Setfos software. The optimization of different parameters of layer structure of solar cell would help to achieve maximum light absorption in the perovskite layer of solar cell. Simulation study is based drift-diffusion model to study the different parameters of perovskite solar cell. Hysteresis is one of the factors in the perovskite solar cell which may influence the device performance. The measurement of abnormal hysteresis can be done by current-voltage curve during backward scan during simulation study. In backward scan, the measurement starts from biasing voltage higher than open circuit voltage and sweep to voltage below zero. The numerical simulation used to study the various parameters like open circuit voltage, short circuit current, fill factor, power conversion efficiency and hysteresis. The simulation results would help to understand the photophysics of solar cell physics which would help to fabricate highly efficient and stable perovskite solar cells experimentally.

scholarly journals Analysis of the role of hole transport layer materials to the performance of perovskite solar cell

2018 ◽  
Vol 67 ◽  
pp. 01021 ◽  
Author(s):  
Istighfari Dzikri ◽  
Michael Hariadi ◽  
Retno Wigajatri Purnamaningsih ◽  
Nji Raden Poespawati
Keyword(s):  
Solar Cells ◽  
Solar Cell ◽  
Short Circuit ◽  
Perovskite Solar Cells ◽  
Perovskite Solar Cell ◽  
Open Circuit ◽  
Hole Transport ◽  
Transport Layer ◽  
Hole Transport Layer

Research in solar cells is needed to maximize Indonesia’s vast solar potential that can reach up to 207.898 MW with an average radiation of 4.8 kWh/m2/day. Organometallic perovskite solar cells (PSCs) have gained immense attention due to their rapid increase in efficiency and compatibility with low-cost fabrication methods. Understanding the role of hole transport layer is very important to obtain highly efficient PSCs. In this work, we studied the effect of Hole Transport Layer (HTL) to the performance of perovskite solar cell. The devices with HTL exhibit substantial increase in power conversion efficiency, open circuit voltage and short circuit current compared to the device without HTL. The best performing device is PSC with CuSCN as HTL layer, namely Voc of 0.24, Isc of 1.79 mA, 0.27 FF and efficiency of 0.09%.

Two-Dimensional Modelling and Simulation of Crystalline Silicon n+pp+ Solar Cell

2012 ◽  
Vol 260-261 ◽  
pp. 154-162
Author(s):  
S. Tobbeche ◽  
M.N. Kateb
Keyword(s):  
Solar Cell ◽  
Open Circuit Voltage ◽  
Crystalline Silicon ◽  
Spectral Response ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Open Circuit ◽  
The Other ◽  
Electrical Characteristics

In this work, we present the simulation results of the technological parameters and the electrical characteristics of a crystalline silicon n+pp+ solar cell, using two-dimension (2D) software, namely TCAD Silvaco (Technology Computer Aided Design). TCAD Silvaco Athena is used to simulate various stages of the technology manufacturing, while TCAD Silvaco Atlas is used for the simulation of the electrical characteristics and the spectral response of the solar cell. The J-V characteristics and the external quantum efficiency (EQE) are simulated under AM 1.5 illumination. The conversion efficiency(η)of 16.06% is reached and the other characteristic parameters are simulated: the open circuit voltage (Voc) is of 0.63 V, the short circuit current density (Jsc) equals 30.54 mA/cm² and the form factor (FF) is of 0.83 for the n+pp+ solar cell with a silicon nitride antireflection layer (Si3N4). In order to highlight the importance of the back surface field (BSF), a comparison between two cells, one without BSF (structure n+p), the other with one BSF (structure n+pp+), was made. By creating a BSF on the rear face of the cell the short circuit current density increases from 28.55 to 30.54 mA/cm2, the open circuit voltage from 0.6 to 0.63 V and the conversion efficiency from 14.19 to 16.06%. A clear improvement of the spectral response is obtained in wavelengths ranging from 0.65 to 1.1 µm for the solar cell with BSF.

scholarly journals Novel perovskite solar cell with Distributed Bragg Reflector

PLoS ONE ◽  
2021 ◽  
Vol 16 (12) ◽  
pp. e0259778
Author(s):  
Waqas Farooq ◽  
Shanshan Tu ◽  
Syed Asfandyar Ali Kazmi ◽  
Sadaqat ur Rehman ◽  
Adnan Daud Khan ◽  
...  
Keyword(s):  
Solar Cell ◽  
Short Circuit ◽  
Short Circuit Current ◽  
High Energy ◽  
Perovskite Solar Cell ◽  
Open Circuit ◽  
Bragg Reflector ◽  
Lead Iodide ◽  
Distributed Bragg Reflector ◽  
Perovskite Material

This paper reports numerical modeling of perovskite solar cell which has been knotted with Distributed Bragg Reflector pairs to extract high energy efficiency. The geometry of the proposed cells is simulated with three different kinds of perovskite materials including CH3NH3PbI3, CH3NH3PbBr3, and CH3NH3SnI3. The toxic perovskite material based on Lead iodide and lead bromide appears to be more efficient as compared to non-toxic perovskite material. The executed simulated photovoltaic parameters with the highest efficient structure are open circuit voltage = 1.409 (V), short circuit current density = 24.09 mA/cm2, fill factor = 86.18%, and efficiency = 24.38%. Moreover, a comparison of the current study with different kinds of structures has been made and surprisingly our novel geometry holds enhanced performance parameters that are featured with back reflector pairs (Si/SiO2). The applied numerical approach and presented designing effort of geometry are beneficial to obtain results that have the potential to address problems with less efficient thin-film solar cells.

Modeling of a high performance bandgap graded Pb-free HTM-free perovskite solar cell

2019 ◽  
Vol 87 (1) ◽  
pp. 10101 ◽  
Author(s):  
Davoud Jalalian ◽  
Abbas Ghadimi ◽  
Azadeh Kiani
Keyword(s):  
Solar Cell ◽  
High Performance ◽  
Fill Factor ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Perovskite Solar Cell ◽  
Short Circuit Current Density ◽  
Open Circuit ◽  
Hole Transport ◽  
Cell Capacitance

In this study, a lead-free nontoxic and hole transport material (HTM)-free perovskite solar cell (PSC) with a novel configuration of glass/FTO/ZnO/CH3NH3SnI3−xBrx/back contact has been modeled and optimized by a solar cell capacitance simulator (SCAPS). The bandgap of CH3NH3SnI3−xBrx absorber is tuned in the range of 1.3 eV to 2.15 eV by variation of the Br doping content. To make a comparison, an optimized Pb-based PSC is also modeled. By optimizing the parameters, power conversion efficiency (PCE) of 16.30%, open circuit voltage (Voc) of 1.02 V, short circuit current density (Jsc) of 22.23 mA/cm2, and fill factor (FF) of 0.72 were obtained. As compare to the reports available in the literature, these results show much improvement and can provide guidelines for production of economic and environmentally friendly PSCs with further efficiency enhancement.

scholarly journals Thickness Variation Effects on the Efficiency of Simulated Hybrid Cu2ZnSnS4-Based Solar Cells Using SCAPS-1D

2021 ◽  
Vol 12 (6) ◽  
pp. 7478-7487
Keyword(s):  
Solar Cells ◽  
Solar Cell ◽  
Conversion Efficiency ◽  
Short Circuit ◽  
Perovskite Solar Cells ◽  
Short Circuit Current ◽  
Step Length ◽  
Open Circuit ◽  
Thickness Variation ◽  
Percentage Conversion

This study presents the simulations of a hybrid Cu2ZnSnS4-based solar cell with a planar heterojunction structure in a hybrid model (n-FTO/n-ZnO/p-PSCS/p-CZTS/p-PSCS/p-HTM) using a One-Dimensional Solar cell capacitance simulator (SCAPS-1D). . The configuration "121" of the hybridizing absorber layers of the device was simulated and related with as-Copper Zinc Tin Sulphide (CZTS). The simulation used an absorber layer with a step-length thickness of 25 nm and thicknesses ranging from 100 nm to 500 nm. The bandgap diagram, I-V characteristics curve, percentage conversion efficiencies, and the quantum efficiencies of the simulated solar cells were calculated and constructed from simulated results. The percentage conversion efficiency of 22.57%, fill factor of 49.99%, open-circuit voltage of 0.80V, and short circuit current of 25.12 mAcm-2 were obtained. The obtained photon conversion efficiency shows that the hybridization of different absorber layers was achievable. It was also established that the performance efficiencies of hybrid CZTS structure in terms of optimum thickness and sandwiched Perovskite Solar cells model (FTO/ZnO/CZTS/PSCS/CZTS/HTM) has the same efficiencies for "121 configurations". On the other hand, the efficiencies of as- CZTS structures were higher than the PSCS configuration, which might be due to SCAPS-1D as it was originally designed for Thin Films Solar cells.

scholarly journals CdTe-Based Thin Film Solar Cells: Past, Present and Future

Energies ◽  
2021 ◽  
Vol 14 (6) ◽  
pp. 1684
Author(s):  
Alessandro Romeo ◽  
Elisa Artegiani
Keyword(s):  
Thin Film ◽  
Solar Cells ◽  
Solar Cell ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Open Circuit ◽  
Early Years ◽  
Solar Cell Efficiency ◽  
Cell Efficiency

CdTe is a very robust and chemically stable material and for this reason its related solar cell thin film photovoltaic technology is now the only thin film technology in the first 10 top producers in the world. CdTe has an optimum band gap for the Schockley-Queisser limit and could deliver very high efficiencies as single junction device of more than 32%, with an open circuit voltage of 1 V and a short circuit current density exceeding 30 mA/cm2. CdTe solar cells were introduced at the beginning of the 70s and they have been studied and implemented particularly in the last 30 years. The strong improvement in efficiency in the last 5 years was obtained by a new redesign of the CdTe solar cell device reaching a single solar cell efficiency of 22.1% and a module efficiency of 19%. In this paper we describe the fabrication process following the history of the solar cell as it was developed in the early years up to the latest development and changes. Moreover the paper also presents future possible alternative absorbers and discusses the only apparently controversial environmental impacts of this fantastic technology.

scholarly journals GaInP/GaAs/poly-Si Multi-Junction Solar Cells by in Metal Balls Bonding

Crystals ◽  
2021 ◽  
Vol 11 (7) ◽  
pp. 726
Author(s):  
Ray-Hua Horng ◽  
Yu-Cheng Kao ◽  
Apoorva Sood ◽  
Po-Liang Liu ◽  
Wei-Cheng Wang ◽  
...  
Keyword(s):  
Solar Cells ◽  
Solar Cell ◽  
Low Temperature ◽  
Triple Junction ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Open Circuit ◽  
Metal Line ◽  
Solar Simulator ◽  
Junction Solar Cell

In this study, a mechanical stacking technique has been used to bond together the GaInP/GaAs and poly-silicon (Si) solar wafers. A GaInP/GaAs/poly-Si triple-junction solar cell has mechanically stacked using a low-temperature bonding process which involves micro metal In balls on a metal line using a high-optical-transmission spin-coated glue material. Current–voltage measurements of the GaInP/GaAs/poly-Si triple-junction solar cells have carried out at room temperature both in the dark and under 1 sun with 100 mW/cm2 power density using a solar simulator. The GaInP/GaAs/poly-Si triple-junction solar cell has reached an efficiency of 24.5% with an open-circuit voltage of 2.68 V, a short-circuit current density of 12.39 mA/cm2, and a fill-factor of 73.8%. This study demonstrates a great potential for the low-temperature micro-metal-ball mechanical stacking technique to achieve high conversion efficiency for solar cells with three or more junctions.

Enhancement of the performance of CdS/CdTe heterojunction solar cell using TiO2/ZnO bi-layer ARC and V2O5 BSF layers: A simulation approach

2020 ◽  
Vol 92 (2) ◽  
pp. 20901
Author(s):  
Abdul Kuddus ◽  
Md. Ferdous Rahman ◽  
Jaker Hossain ◽  
Abu Bakar Md. Ismail
Keyword(s):  
Solar Cell ◽  
Short Circuit ◽  
Photovoltaic Performance ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Open Circuit ◽  
Heterojunction Solar Cell ◽  
Back Surface ◽  
Heterojunction Solar Cells

This article presents the role of Bi-layer anti-reflection coating (ARC) of TiO2/ZnO and back surface field (BSF) of V2O5 for improving the photovoltaic performance of Cadmium Sulfide (CdS) and Cadmium Telluride (CdTe) based heterojunction solar cells (HJSCs). The simulation was performed at different concentrations, thickness, defect densities of each active materials and working temperatures to optimize the most excellent structure and working conditions for achieving the highest cell performance using obtained optical and electrical parameters value from the experimental investigation on spin-coated CdS, CdTe, ZnO, TiO2 and V2O5 thin films deposited on the glass substrate. The simulation results reveal that the designed CdS/CdTe based heterojunction cell offers the highest efficiency, η of ∼25% with an enhanced open-circuit voltage, Voc of 0.811 V, short circuit current density, Jsc of 38.51 mA cm−2, fill factor, FF of 80% with bi-layer ARC and BSF. Moreover, it appears that the TiO2/ZnO bi-layer ARC, as well as ETL and V2O5 as BSF, could be highly promising materials of choice for CdS/CdTe based heterojunction solar cell.

Sign in / Sign up

Export Citation Format

Share Document