scholarly journals Wide Input Voltage Range Operation of the Series Resonant DC-DC Converter with Bridgeless Boost Rectifier

Energies ◽  
2020 ◽  
Vol 13 (16) ◽  
pp. 4220
Author(s):  
Abualkasim Bakeer ◽  
Andrii Chub ◽  
Dmitri Vinnikov ◽  
Argo Rosin
Keyword(s):  
Input Voltage ◽  
Voltage Regulation ◽  
Operating Conditions ◽  
Reverse Direction ◽  
Switching Frequency ◽  
Half Cycle ◽  
Wide Range ◽  
Series Resonant ◽  
Boost Rectifier ◽  
Abnormal Operating Conditions

The series resonant DC-DC converter (SRC) can regulate the input voltage in a wide range at a fixed switching frequency. In this work, the bridgeless rectifier, which is utilized intensively in the applications of the power factor correction, has been integrated into the SRC as a voltage step-up cell at the output-side of the SRC. It is shown that the conventional overlapping pulse-width modulation (PWM) of the two metal oxide semiconductor field-effect transistors MOSFETs in this rectification cell limits the input voltage regulation range of the converter due to excessive power losses in abnormal operating conditions. The abnormal operating conditions occur when the instantaneous voltage across the resonant capacitor is larger than the secondary voltage of the isolation transformer. This happens at high values of the DC voltage gain, i.e., low input voltages and high currents, which causes the resonant current to flow in the reverse direction in the same half-cycle through a parasitic path formed by overlapping PWM of the rectifier MOSFETs. The abnormal operation results in additional conduction loss in the converter as the MOSFETs of the bridgeless boost rectifier turn on at high current at the beginning of each half of the switching period. Accordingly, the overall efficiency of the converter significantly deteriorates. This paper proposes the hybrid PWM aiming to improve the efficiency of the SRC with a bridgeless boost rectifier in a wide input voltage regulation range. The converter swaps between the overlapping and the proposed short-pulse PWM schemes to drive the MOSFETs in the bridgeless boost rectifier. The transition between the two PWM schemes is defined according to the boundary condition that relies upon the operating point of the converter power and the input voltage. The proposed hybrid PWM scheme is analyzed and compared to the overlapping PWM at different levels of the input voltage and the load power. A 300 W prototype was studied in the laboratory to show the feasibility of the proposed hybrid PWM scheme with the closed-loop control system to switch between the two PWM schemes.

scholarly journals Step-Up Series Resonant DC–DC Converter with Bidirectional-Switch-Based Boost Rectifier for Wide Input Voltage Range Photovoltaic Applications

Energies ◽  
2020 ◽  
Vol 13 (14) ◽  
pp. 3747 ◽  
Author(s):  
Abualkasim Bakeer ◽  
Andrii Chub ◽  
Dmitri Vinnikov
Keyword(s):  
Theoretical Analysis ◽  
Duty Cycle ◽  
Input Voltage ◽  
Voltage Regulation ◽  
Switching Frequency ◽  
Voltage Gain ◽  
Voltage Range ◽  
Dc Voltage ◽  
Wide Range ◽  
Series Resonant

This paper proposes a high gain DC–DC converter based on the series resonant converter (SRC) for photovoltaic (PV) applications. This study considers low power applications, where the resonant inductance is usually relatively small to reduce the cost of the converter realization, which results in low-quality factor values. On the other hand, these SRCs can be controlled at a fixed switching frequency. The proposed topology utilizes a bidirectional switch (AC switch) to regulate the input voltage in a wide range. This study shows that the existing topology with a bidirectional switch has a limited input voltage regulation range. To avoid this issue, the resonant tank is rearranged in the proposed converter to the resonance capacitor before the bidirectional switch. By this rearrangement, the dependence of the DC voltage gain on the duty cycle is changed, so the proposed converter requires a smaller duty cycle than that of the existing counterpart at the same gain. Theoretical analysis shows that the input voltage regulation range is extended to the region of high DC voltage gain values at the maximum input current. Contrary to the existing counterpart, the proposed converter can be realized with a wide range of the resonant inductance values without compromising the input voltage regulation range. Nevertheless, the proposed converter maintains advantages of the SRC, such as zero voltage switching (ZVS) turn-on of the primary-side semiconductor switches. In addition, the output-side diodes are turned off at zero current. The proposed converter is analyzed and compared with the existing counterpart theoretically and experimentally. A 300 W experimental prototype is used to validate the theoretical analysis of the proposed converter. The peak efficiency of the converter is 96.5%.

scholarly journals Wide Range Series Resonant DC-DC Converter with a Reduced Component Count and Capacitor Voltage Stress for Distributed Generation

Energies ◽  
2021 ◽  
Vol 14 (8) ◽  
pp. 2051
Author(s):  
Abualkasim Bakeer ◽  
Andrii Chub ◽  
Andrei Blinov ◽  
Jih-Sheng Lai
Keyword(s):  
Distributed Generation ◽  
Input Voltage ◽  
Voltage Regulation ◽  
Maximum Efficiency ◽  
Half Cycle ◽  
Wide Range ◽  
Voltage Stress ◽  
Capacitor Voltage ◽  
Output Side ◽  
Boost Rectifier

This paper proposes a galvanically isolated dc-dc converter that can regulate the input voltage in a wide range. It is based on the series resonance dc-dc converter (SRC) topology and a novel boost rectifier. The proposed topology has a smaller number of semiconductors than its SRC-based existing topologies employing an ac-switch in the boost rectifier. The proposed dc-dc converter comprises only two diodes and one switch at the output side, while the existing solutions use two switches and two diodes to step up the voltage. The proposed converter boosts the input voltage within a single boosting interval in the positive half-cycle of the switching period. In addition, the resonant current in the negative half-cycle is sinusoidal, which could enhance the converter efficiency. The resonant capacitor voltage is clamped at the level of the output voltage. Therefore, the voltage stress of the capacitor could significantly reduce at various input voltage and power levels. This makes it perfect for distributed generation applications such as photovoltaics with wide variations of input voltage and power. The converter operates at the fixed switching frequency close to the resonance frequency to obtain the maximum efficiency at the nominal input voltage. The zero-voltage switching (ZVS) feature is achieved in the primary semiconductors, while the diodes in the output-side rectifier turn off at nearly zero current switching. The mathematical model and design guidelines of the proposed converter are discussed in the paper. The experimental results confirmed the theoretical analysis based on a 300 W prototype. The maximum efficiency of the converter was 96.8% at the nominal input voltage, and the converter has achieved a wider input voltage regulation range than that with the boosting cell comprising an ac-switch.

scholarly journals Influence of Power Losses in the Inductor Core on Characteristics of Selected DC–DC Converters

Energies ◽  
2019 ◽  
Vol 12 (10) ◽  
pp. 1991 ◽  
Author(s):  
Krzysztof Górecki ◽  
Kalina Detka
Keyword(s):  
Nanocrystalline Material ◽  
Input Voltage ◽  
Load Resistance ◽  
Operating Conditions ◽  
Switching Frequency ◽  
Power Losses ◽  
Boost Converters ◽  
The Core ◽  
Operation Conditions ◽  
Wide Range

The paper presents the results of a computer simulation illustrating the influence of power losses in the core of an inductor based on the characteristics of buck and boost converters. In the computations, the authors’ model of power losses in the core is used. Correctness of this model is verified experimentally for three different magnetic materials. Computations are performed with the use of this model and the Excel software for inductors including cores made of ferrite, powdered iron, and nanocrystalline material in a wide range of load resistance, as well as input voltage of both the considered converters operating at different values of switching frequency. The obtained computation results show that power losses in the inductor core and watt-hour efficiency of converters strongly depend on the material used to make this core, in addition to the input voltage and parameters of the control signal and load resistance of the considered converters. The obtained results of watt-hour efficiency of the considered direct current (DC)–DC converters show that it changes up to 30 times in the considered ranges of the mentioned factors. In turn, in the same operating conditions, values of power losses in the considered cores change from a fraction of a watt to tens of watts. The paper also considers the issue of which material should be used to construct the inductor core in order to obtain the highest value of watt-hour efficiency at selected operation conditions of the considered converters.

scholarly journals Performance Improvement of PWM Control Methods for Voltage Step-Down in Series Resonant DC–DC Converters

Energies ◽  
2020 ◽  
Vol 13 (17) ◽  
pp. 4569
Author(s):  
Vadim Sidorov ◽  
Andrii Chub ◽  
Dmitri Vinnikov
Keyword(s):  
Power Conversion Efficiency ◽  
Conversion Efficiency ◽  
Pulse Width Modulation ◽  
Renewable Energy Sources ◽  
Power Conversion ◽  
Input Voltage ◽  
Voltage Regulation ◽  
Switching Frequency ◽  
Semiconductor Switches ◽  
Series Resonant

The paper is focused on galvanically isolated series resonant DC–DC converters (SRCs) with a low quality factor of the resonant tank. These converters provide input voltage regulation at fixed switching frequency and good power density. Different modulation methods at the fixed switching frequency enable the implementation of the voltage buck functionality in these converters. The SRC under study is considered as a step-up front-end DC–DC converter for the integration of renewable energy sources in DC microgrids. The paper evaluates the voltage buck performance of the SRC achieved by using different pulse-width modulation (PWM) methods including conventional PWM and shifted PWM. Moreover, the new PWM methods, i.e., the hybrid shifted PWM (HSPWM), improved shifted PWM (ISPWM), and hybrid PWM (HPWM), are proposed to overcome the disadvantages of the existing methods. They improve the power conversion efficiency in the buck mode by reducing the power losses in the semiconductor switches and the isolating transformer of the SRC. The proposed and the existing methods are benchmarked in terms of the components stresses and power conversion efficiency. The presented findings have been experimentally validated by the help of a 200 W prototype, which demonstrated the lowest power loss in the case of the HPWM.

scholarly journals Identification of DC Thermal Steady-State Differential Inductance of Ferrite Power Inductors

Energies ◽  
2021 ◽  
Vol 14 (13) ◽  
pp. 3854
Author(s):  
Salvatore Musumeci ◽  
Luigi Solimene ◽  
Carlo Stefano Ragusa
Keyword(s):  
Steady State ◽  
Input Voltage ◽  
Switching Frequency ◽  
Ohmic Losses ◽  
Steady State Temperature ◽  
Wide Range ◽  
Average Current ◽  
Power Inductors ◽  
Saturable Inductor ◽  
Thermal Steady State

In this paper, we propose a method for the identification of the differential inductance of saturable ferrite inductors adopted in DC–DC converters, considering the influence of the operating temperature. The inductor temperature rise is caused mainly by its losses, neglecting the heating contribution by the other components forming the converter layout. When the ohmic losses caused by the average current represent the principal portion of the inductor power losses, the steady-state temperature of the component can be related to the average current value. Under this assumption, usual for saturable inductors in DC–DC converters, the presented experimental setup and characterization method allow identifying a DC thermal steady-state differential inductance profile of a ferrite inductor. The curve is obtained from experimental measurements of the inductor voltage and current waveforms, at different average current values, that lead the component to operate from the linear region of the magnetization curve up to the saturation. The obtained inductance profile can be adopted to simulate the current waveform of a saturable inductor in a DC–DC converter, providing accurate results under a wide range of switching frequency, input voltage, duty cycle, and output current values.

scholarly journals Dual-Mode Power Operation for Grid-Connected PV Systems with Adaptive DC-link Controller

2021 ◽  
Author(s):  
Mostafa Ahmed ◽  
Ibrahim Harbi ◽  
Ralph Kennel ◽  
Mohamed Abdelrahem
Keyword(s):  
Power Generation ◽  
Voltage Regulation ◽  
Operating Conditions ◽  
Switching Frequency ◽  
Atmospheric Conditions ◽  
Voltage Profile ◽  
Dual Mode ◽  
Power Extraction ◽  
Pv Systems ◽  
Power Operation

AbstractPhotovoltaic (PV) power systems are integrated with high penetration levels into the grid. This in turn encourages several modifications for grid codes to sustain grid stability and resilience. Recently, constant power management and regulation is a very common approach, which is used to limit the PV power production. Thus, this article proposes dual-mode power generation algorithm for grid-connected PV systems. The developed system considers the two-stage PV configuration for implementation, where the dual-mode power generation technique is executed within the DC–DC conversion (boost) stage. Most of the techniques adopted for dual-mode power operation employ the conventional perturb and observe method, which is known with unsatisfactory performance at fast-changing atmospheric conditions. Considering this issue, this study suggests a modified maximum power point tracker for power extraction. Furthermore, a new adaptive DC-link controller is developed to improve the DC-link voltage profile at different operating conditions. The adaptive DC-link controller is compared with the traditional PI controller for voltage regulation. The inverter control is accomplished using finite-set model predictive control with two control objectives, namely reference current tracking and switching frequency minimization. The overall control methodology is evaluated at different atmospheric and operating conditions using MATLAB/Simulink software.

A Simple Design Approach for Excitation Controller and Power System Stabilizer

2010 ◽  
Author(s):  
G. Fusco ◽  
M. Russo
Keyword(s):  
Power System ◽  
Transient Stability ◽  
Short Circuit ◽  
Design Procedure ◽  
Voltage Regulation ◽  
Operating Conditions ◽  
Power System Stabilizer ◽  
Simple Design ◽  
Wide Range ◽  
System Stabilizer

This paper proposes a simple design procedure to solve the problem of controlling generator transient stability following large disturbances in power systems. A state-feedback excitation controller and power system stabilizer are designed to guarantee robustness against uncertainty in the system parameters. These controllers ensure satisfactory swing damping and quick decay of the voltage regulation error over a wide range of operating conditions. The controller performance is evaluated in a case study in which a three-phase short-circuit fault near the generator terminals in a four-bus power system is simulated.

Process Safety for Sustainable Applications

2021 ◽  
pp. 2150033
Author(s):  
Alexander Stolar ◽  
Anton Friedl
Keyword(s):  
Risk Management ◽  
Operating Conditions ◽  
Process Safety ◽  
Implementation Effort ◽  
Wide Range ◽  
System Improvement ◽  
Management Techniques ◽  
Universal Applicability ◽  
Abnormal Operating Conditions ◽  
Business Sectors

Process safety techniques have been used in industry for decades to make processes and systems safer and to optimize them, and thus to improve sustainability. Their main aim is to prevent damage to people, equipment and the environment. In this overview, process safety and risk management techniques are shown that can be applied in the different life cycle phases of an application without much implementation effort. A broad and universal applicability in a wide range of business sectors is set as the main focus. In addition to the application of system improvement techniques, a number of additional considerations, such as maintenance and the consideration of abnormal operating conditions, are included in order to be able to comprehensively improve a system or application.

scholarly journals Induction Motor Drives Fed by an NPC Inverter with Unbalanced DC-Link

Electronics ◽  
2019 ◽  
Vol 8 (12) ◽  
pp. 1379 ◽  
Author(s):  
Umberto Abronzini ◽  
Ciro Attaianese ◽  
Matilde D’Arpino ◽  
Mauro Di Monaco ◽  
Giuseppe Tomasso
Keyword(s):  
Output Voltage ◽  
Harmonic Distortion ◽  
Voltage Regulation ◽  
Motor Drives ◽  
Operating Conditions ◽  
Switching Frequency ◽  
Voltage Level ◽  
Voltage Quality ◽  
Vector Modulation

Neutral Point Clamped (NPC) converters with n levels are traditionally controlled in such a way that the DC-link capacitors operate at 1/( n - 1) of the total DC-link voltage level. The voltage level across the DC-link capacitors has to be properly regulated by the capacitor unbalance control to contain the harmonic distortion of the converter output voltages. State-of-the-art modulation techniques address the problem of the DC-link voltage regulation for NPC inverters. However, they highly show reduced performance when unbalanced DC-link voltages are considered. In this paper, a novel Space Vector Modulation (SVM) is proposed for NPC converters with an unbalanced DC-link. At every modulation interval, the technique defines the optimal switching pattern by considering the actual unbalanced DC-link conditions. The proposed modulation allows improving the harmonic content of the NPC converter output voltage with respect to a traditional ML-SVM, when the same operating conditions are considered. As an extension, the proposed modulation technique will guarantee the same output voltage quality of a traditional ML-SVM with unbalanced DC-link, while improving the conversion efficiency thanks to a reduction of switching frequency.

scholarly journals X-Type Step-Up Multi-Level Inverter with Reduced Component Count Based on Switched-Capacitor Concept

Electronics ◽  
2020 ◽  
Vol 9 (12) ◽  
pp. 1987
Author(s):  
Erfan Azimi ◽  
Aryorad Khodaparast ◽  
Mohammad Javad Rostami ◽  
Jafar Adabi ◽  
M. Ebrahim Adabi ◽  
...  
Keyword(s):  
Power Flow ◽  
Input Voltage ◽  
Switching Frequency ◽  
Switched Capacitor ◽  
Level Control ◽  
Voltage Balancing ◽  
Simulink Model ◽  
Wide Range ◽  
Multi Level ◽  
Laboratory Prototype

This paper aims to present a novel switched-capacitor multi-level inverter. The presented structure generates a staircase near sinusoidal AC voltage by using a single DC source and a few capacitors to step-up the input voltage. The nearest level control (NLC) strategy is used to control the operation of the converter. These switching states are designed in a way that they always ensure the self-voltage balancing of the capacitors. Low switching frequency, simple control, and inherent bipolar output are some of the advantages of the presented inverter. Compared to other existing topologies, the structure requires fewer circuit elements. Bi-directional power flow ability of the proposed topology, facilitates the operation of the circuit under wide range of load behaviors which makes it applicable in most industries. Besides, a 13-level laboratory prototype is implemented to realize and affirm the efficacy of the MATLAB Simulink model under different load conditions. The simulation and experimental results accredit the appropriate performance of the converter. Finally, a theoretical efficiency of 92.73% is reached.

Sign in / Sign up

Export Citation Format

Share Document