scholarly journals An Optimized PV Control System Based on the Emperor Penguin Optimizer

Energies ◽  
2021 ◽  
Vol 14 (3) ◽  
pp. 751
Author(s):  
Mariam A. Sameh ◽  
Mostafa I. Marei ◽  
M. A. Badr ◽  
Mahmoud A. Attia
Keyword(s):  
Duty Cycle ◽  
Optimization Technique ◽  
Pso Algorithm ◽  
Boost Converter ◽  
Emperor Penguin ◽  
Pv System ◽  
Partial Shading ◽  
Pv Systems ◽  
Point Tracking ◽  
Grid Connected Inverter

During the day, photovoltaic (PV) systems are exposed to different sunlight conditions in addition to partial shading (PS). Accordingly, maximum power point tracking (MPPT) techniques have become essential for PV systems to secure harvesting the maximum possible power from the PV modules. In this paper, optimized control is performed through the application of relatively newly developed optimization algorithms to PV systems under Partial Shading (PS) conditions. The initial value of the duty cycle of the boost converter is optimized for maximizing the amount of power extracted from the PV arrays. The emperor penguin optimizer (EPO) is proposed not only to optimize the initial setting of duty cycle but to tune the gains of controllers used for the boost converter and the grid-connected inverter of the PV system. In addition, the performance of the proposed system based on the EPO algorithm is compared with another newly developed optimization technique based on the cuttlefish algorithm (CFA). Moreover, particle swarm optimization (PSO) algorithm is used as a reference algorithm to compare results with both EPO and CFA. PSO is chosen since it is an old, well-tested, and effective algorithm. For the evaluation of performance of the proposed PV system using the proposed algorithms under different PS conditions, results are recorded and introduced.

scholarly journals A Modification of the Perturb and Observe Method to Improve the Energy Harvesting of PV Systems under Partial Shading Conditions

Energies ◽  
2021 ◽  
Vol 14 (9) ◽  
pp. 2521
Author(s):  
Alfredo Gil-Velasco ◽  
Carlos Aguilar-Castillo
Keyword(s):  
Maximum Power ◽  
Global Maximum ◽  
Pv System ◽  
Maximum Power Point ◽  
Partial Shading ◽  
Pv Systems ◽  
Point Tracking ◽  
Power Point Tracking ◽  
Power Point ◽  
Computational Resources

There are multiples conditions that lead to partial shading conditions (PSC) in photovoltaic systems (PV). Under these conditions, the harvested energy decreases in the PV system. The maximum power point tracking (MPPT) controller aims to harvest the greatest amount of energy even under partial shading conditions. The simplest available MPPT algorithms fail on PSC, whereas the complex ones are effective but require high computational resources and experience in this type of systems. This paper presents a new MPPT algorithm that is simple but effective in tracking the global maximum power point even in PSC. The simulation and experimental results show excellent performance of the proposed algorithm. Additionally, a comparison with a previously proposed algorithm is presented. The comparison shows that the proposal in this paper is faster in tracking the maximum power point than complex algorithms.

Research on Photovoltaic Industry with the MPPT Algorithm in PV System

2013 ◽  
Vol 345 ◽  
pp. 359-363
Author(s):  
Shi Die Shen ◽  
Wei Yao
Keyword(s):  
Duty Cycle ◽  
Boost Converter ◽  
Experimental Results ◽  
Pv System ◽  
Maximum Power Point ◽  
Matlab Simulink ◽  
Point Tracking ◽  
Power Point Tracking ◽  
Variable Step ◽  
Power Point

In this paper, photovoltaic industry is introduced briefly. For the shortcomings of the fixed-step perturbation and observation (P&O) method in the maximum power point tracking (MPPT) technology, a variable-step P&O method is proposed and the algorithm is further improved. In the PV system, the MPPT is realized by changing the duty cycle of switching tube in the Boost converter. The simulations were conducted in the Matlab/Simulink platform. At last, the experimental results on the 3kw prototype showed that the new MPPT algorithm is effective.

scholarly journals Implementation of MPPT for PV Isolated System by P&O, I_C and PSO Methods based on Arduino Technology

2019 ◽  
Vol 3 (6) ◽  
Author(s):  
Eid A. Gouda ◽  
Mohamed Fawzi Kotb ◽  
Dina A. Elalfy
Keyword(s):  
Optimization Methods ◽  
Pso Algorithm ◽  
Maximum Power ◽  
Pv System ◽  
Pv Systems ◽  
Point Tracking ◽  
Power Point Tracking ◽  
Proposed Model ◽  
Arduino Uno ◽  
Power Point

Maximum power point tracking (MPPT) algorithms are very important for the PV systems because they attract the points of maximum power at any conditions of the varying temperature and irradiation and subsequently decrease the PV array cost. This paper presents an improved MPPT technique for the PV system using particle swarm optimization (PSO) algorithm comparing with the conventional MPPT methods using perturb and observe (P&O) and incremental conductance (I_C).  MATLAB simulations are carried out under the same irradiation and temperature and a variation in the load and comparing the performance of the three methods. In Protues 8.3 professional software, a design of the proposed model using Arduino UNO of the three algorithms is achieved. One of the important contributions of this paper is the proposed experimental work which is carried out by the combination of Arduino UNO which is coded by C language and coupled with MATLAB results which obtained by the simulation for the used different optimization methods in this paper. At the end of this paper, there is a comparison in tabular form between the presented 3 optimization methods with their experimental results. It is found that the results obtained by using PSO are more acceptable. The main advantages of the PSO are as follows: - it reduces the oscillations at the steady state (to approximately zero) once the MPP is located, and its algorithm is very fast comparing to the other two methods.

Comprehensive improvement of artificial fish swarm algorithm for global MPPT in PV system under partial shading conditions

2017 ◽  
Vol 40 (7) ◽  
pp. 2178-2199 ◽  
Author(s):  
Mingxuan Mao ◽  
Qichang Duan ◽  
Pan Duan ◽  
Bei Hu
Keyword(s):  
Pso Algorithm ◽  
Learning Ability ◽  
Pv System ◽  
Partial Shading ◽  
Artificial Fish Swarm Algorithm ◽  
Pv Systems ◽  
Artificial Fish Swarm ◽  
Swarm Algorithm ◽  
Power Point ◽  
Global Mppt

Due to the non-linear characteristics I–V of the photovoltaic (PV) curve, the tracking of the maximum power point (MPP) under partial shading (PS) conditions can sometimes be a challenging task. This paper presents a modified artificial fish swarm algorithm (AFSA) for MPP tracking (MPPT) in PV modules under PS. In this algorithm, the AFSA optimized by particle swarm optimization (PSO) algorithm with extended memory (PSOEM-FSA) is improved by hybridizing it with adaptive visual and step, and the resulting algorithm is a comprehensive improvement on the AFSA (abbreviated as CIAFSA). Combining the searching capabilities of the PSOEM-FSA and the self-learning ability of adaptive visual and step for AFSA, CIAFSA is developed. To validate the effectiveness of this novel MPPT technique, the PV system along with the proposed MPPT algorithm is simulated using the Matlab/Simulink Simscape toolbox. Results show that the proposed approach is more effective in MPPT in PV systems under PS conditions when compared with other methods in searching precision.

scholarly journals Reconfigurable Distributed Power Electronics Technique for Solar PV Systems

Electronics ◽  
2021 ◽  
Vol 10 (9) ◽  
pp. 1121
Author(s):  
Kamran Ali Khan Niazi ◽  
Yongheng Yang ◽  
Tamas Kerekes ◽  
Dezso Sera
Keyword(s):  
Energy Yield ◽  
Solar Pv ◽  
Charge Redistribution ◽  
Pv System ◽  
Partial Shading ◽  
Pv Systems ◽  
Simulation Based ◽  
In Series ◽  
A Cell ◽  
Power Balancing

A reconfiguration technique using a switched-capacitor (SC)-based voltage equalizer differential power processing (DPP) concept is proposed in this paper for photovoltaic (PV) systems at a cell/subpanel/panel-level. The proposed active diffusion charge redistribution (ADCR) architecture increases the energy yield during mismatch and adds a voltage boosting capability to the PV system under no mismatch by connected the available PV cells/panels in series. The technique performs a reconfiguration by measuring the PV cell/panel voltages and their irradiances. The power balancing is achieved by charge redistribution through SC under mismatch conditions, e.g., partial shading. Moreover, PV cells/panels remain in series under no mismatch. Overall, this paper analyzes, simulates, and evaluates the effectiveness of the proposed DPP architecture through a simulation-based model prepared in PSIM. Additionally, the effectiveness is also demonstrated by comparing it with existing conventional DPP and traditional bypass diode architecture.

scholarly journals Maximum Power Point Tracking of PV Systems under Partial Shading Conditions Based on Opposition-Based Learning Firefly Algorithm

2021 ◽  
Vol 13 (5) ◽  
pp. 2656
Author(s):  
Ahmed G. Abo-Khalil ◽  
Walied Alharbi ◽  
Abdel-Rahman Al-Qawasmi ◽  
Mohammad Alobaid ◽  
Ibrahim M. Alarifi
Keyword(s):  
Firefly Algorithm ◽  
Maximum Power ◽  
Pv System ◽  
Maximum Power Point ◽  
Partial Shading ◽  
Point Tracking ◽  
Opposition Based Learning ◽  
Power Point Tracking ◽  
Convergence Process ◽  
Power Point

This work presents an alternative to the conventional photovoltaic maximum power point tracking (MPPT) methods, by using an opposition-based learning firefly algorithm (OFA) that improves the performance of the Photovoltaic (PV) system both in the uniform irradiance changes and in partial shading conditions. The firefly algorithm is based on fireflies’ search for food, according to which individuals emit progressively more intense glows as they approach the objective, attracting the other fireflies. Therefore, the simulation of this behavior can be conducted by solving the objective function that is directly proportional to the distance from the desired result. To implement this algorithm in case of partial shading conditions, it was necessary to adjust the Firefly Algorithm (FA) parameters to fit the MPPT application. These parameters have been extensively tested, converging satisfactorily and guaranteeing to extract the global maximum power point (GMPP) in the cases of normal and partial shading conditions analyzed. The precise adjustment of the coefficients was made possible by visualizing the movement of the particles during the convergence process, while opposition-based learning (OBL) was used with FA to accelerate the convergence process by allowing the particle to move in the opposite direction. The proposed algorithm was simulated in the closest possible way to authentic operating conditions, and variable irradiance and partial shading conditions were implemented experimentally for a 60 [W] PV system. A two-stage PV grid-connected system was designed and deployed to validate the proposed algorithm. In addition, a comparison between the performance of the Perturbation and Observation (P&O) method and the proposed method was carried out to prove the effectiveness of this method over the conventional methods in tracking the GMPP.

scholarly journals Analysis and Design of a Multi-Port DC-DC Converter for Interfacing PV Systems

Energies ◽  
2021 ◽  
Vol 14 (7) ◽  
pp. 1943
Author(s):  
Bader N. Alajmi ◽  
Mostafa I. Marei ◽  
Ibrahim Abdelsalam ◽  
Mohamed F. AlHajri
Keyword(s):  
High Frequency ◽  
Computer Aided Design ◽  
Electromagnetic Transients ◽  
Pv System ◽  
Analysis And Design ◽  
Pv Systems ◽  
Point Tracking ◽  
Power Point Tracking ◽  
Power Point ◽  
Aided Design

A high-frequency multi-port (HFMP) direct current (DC) to DC converter is presented. The proposed HFMP is utilized to interface a photovoltaic (PV) system. The presented HFMP is compact and can perform maximum power point tracking. It consists of a high-frequency transformer with many identical input windings and one output winding. Each input winding is connected to a PV module through an H-bridge inverter, and the maximum PV power is tracked using the perturb and observe (P&O) technique. The output winding is connected to a DC bus through a rectifier. The detailed analysis and operation of the proposed HFMP DC-DC converter are presented. Extensive numerical simulations are conducted, using power system computer aided design (PSCAD)/electromagnetic transients including DC (EMTDC) software, to evaluate the operation and dynamic behavior of the proposed PV interfacing scheme. In addition, an experimental setup is built to verify the performance of the HFMP DC-DC converter.

scholarly journals Different Techniques to Mitigate Partial Shading in Photovoltaic Panels

Energies ◽  
2021 ◽  
Vol 14 (13) ◽  
pp. 3863
Author(s):  
Tiago Alves ◽  
João Paulo N. Torres ◽  
Ricardo A. Marques Lameirinhas ◽  
Carlos A. F. Fernandes
Keyword(s):  
Cell Model ◽  
Research Work ◽  
Experimental Tests ◽  
Operating Conditions ◽  
Pv System ◽  
Partial Shading ◽  
System Architectures ◽  
Pv Systems ◽  
Advantages And Disadvantages ◽  
Pv Panel

The effect of partial shading in photovoltaic (PV) panels is one of the biggest problems regarding power losses in PV systems. When the irradiance pattern throughout a PV panel is inequal, some cells with the possibility of higher power production will produce less and start to deteriorate. The objective of this research work is to present, test and discuss different techniques to help mitigate partial shading in PV panels, observing and commenting the advantages and disadvantages for different PV technologies under different operating conditions. The motivation is to contribute with research, simulation, and experimental work. Several state-of-the-artsolutions to the problem will be presented: different topologies in the interconnection of the panels; different PV system architectures, and also introducing new solution hypotheses, such as different cell interconnections topologies. Alongside, benefits and limitations will be discussed. To obtain actual results, the simulation work was conducted by creating MATLAB/Simulink models for each different technique tested, all centered around the 1M5P PV cell model. The several techniques tested will also take into account different patterns and sizes of partial shading, different PV panel technologies, different values of source irradiation, and different PV array sizes. The results will be discussed and validated by experimental tests.

Maximum Power Point Tracking (MPPT) for a Solar Photovoltaic System: A Review

2015 ◽  
Vol 787 ◽  
pp. 227-232 ◽  
Author(s):  
L.A. Arun Shravan ◽  
D. Ebenezer
Keyword(s):  
Solar Energy ◽  
Maximum Power Point Tracking ◽  
Maximum Power ◽  
Nonlinear Behaviour ◽  
Pv System ◽  
Maximum Power Point ◽  
Pv Systems ◽  
Point Tracking ◽  
Power Point Tracking ◽  
Power Point

In recent years there has been a growing attention towards use of solar energy. Advantages of photovoltaic (PV) systems employed for harnessing solar energy are reduction of greenhouse gas emission, low maintenance costs, fewer limitations with regard to site of installation and absence of mechanical noise arising from moving parts. However, PV systems suffer from relatively low conversion efficiency. Therefore, maximum power point tracking (MPPT) for the solar array is essential in a PV system. The nonlinear behaviour of PV systems as well as variations of the maximum power point with solar irradiance level and temperature complicates the tracking of the maximum power point. This paper reviews various MPPT methods based on three categories: offline, online and hybrid methods. Design of a PV system in a encoding environment has also been reviewed here. Furthermore, different MPPT methods are discussed in terms of the dynamic response of the PV system to variations in temperature and irradiance, attainable efficiency, and implementation considerations.

Sign in / Sign up

Export Citation Format

Share Document