scholarly journals Study on Spectral Radiative Heat Transfer Characteristics of a Windowed Receiver with Particle Curtain

Energies ◽  
2021 ◽  
Vol 14 (10) ◽  
pp. 2801
Author(s):  
Li Wang ◽  
Long Yang ◽  
Junjie Liu ◽  
Pei Wang
Keyword(s):  
Heat Transfer ◽  
Particle Size ◽  
Flow Pattern ◽  
Heat Loss ◽  
Volume Fraction ◽  
Incident Radiation ◽  
Flow Stability ◽  
Heat Transfer Characteristics ◽  
Transfer Characteristics ◽  
Exit Temperature

In this paper, a windowed receiver with a particle curtain is numerically simulated under full-spectrum conditions. The discrete phase model (DPM) is used to model the particle flow and interactions between the particle phase and the air phase. The scattering, absorption of the particle curtain and quartz glass window are considered in detail. The spectral characteristics of glass have an important influence on the heat transfer characteristics and the receiver efficiency. The results show that the quartz window can reduce the convective heat loss and the cavity re-radiation heat loss. Under the same conditions, the receiver efficiency of a windowed receiver with a particle curtain is increased by 11.9% compared with an aerowindow receiver with a particle curtain. Under the same mass flow, the particle curtain thickness and particle size have a non-negligible influence on the flow pattern and temperature distribution of the particle curtain. When the particle curtain thickness is low, the flow stability of the particle curtain is high; as the particle curtain thickness increases, the volume fraction of the particle curtain decreases, and the flow stability of the particle curtain decreases, which affects the shape of the curtain. The scattering and absorption characteristics of the particles are different, resulting in different net fluxes of incident radiation under the reflection of the particle curtain and the back wall. As the particle curtain thickness increases, the particle average exit temperature and the receiver efficiency show a trend of first increasing and then decreasing. When d = 30 mm, the incident radiation (G) at the position of the particle curtain is larger, the particle average exit temperature reaches 1156.72 K, and the receiver efficiency reaches 74.4%. Therefore, different particle sizes also have a significant impact on the flow pattern of the particle curtain and the radiation distribution inside it. In the range of 250–750 μm particle size, the particles average exit temperature reaches above 1150 K, and the receiver efficiency is above 72.6%. As the particle size increases, the particle average exit temperature, and the receiver efficiency show a trend of first decreasing and then increasing. When the particle size is 500 mm, the particle average exit temperature reaches 1175.8 K, and the receiver efficiency reaches 79.4%.

scholarly journals Conduction and convection heat transfer characteristics of water-based au nanofluids in a square cavity with differentially heated side walls subjected to constant temperatures

2014 ◽  
Vol 18 (suppl.1) ◽  
pp. 189-200 ◽  
Author(s):  
Primoz Ternik ◽  
Rebeka Rudolf
Keyword(s):  
Heat Transfer ◽  
Rayleigh Number ◽  
Base Fluid ◽  
Volume Fraction ◽  
Heat Transfer Characteristics ◽  
Square Cavity ◽  
Onset Of Convection ◽  
Transfer Characteristics ◽  
Wide Range ◽  
Water Based

The present work deals with the natural convection in a square cavity filled with the water-based Au nanofluid. The cavity is heated on the vertical and cooled from the adjacent wall, while the other two horizontal walls are adiabatic. The governing differential equations have been solved by the standard finite volume method and the hydrodynamic and thermal fields were coupled together using the Boussinesq approximation. The main objective of this study is to investigate the influence of the nanoparticles? volume fraction on the heat transfer characteristics of Au nanofluids at the given base fluid?s (i.e. water) Rayleigh number. Accurate results are presented over a wide range of the base fluid Rayleigh number and the volume fraction of Au nanoparticles. It is shown that adding nanoparticles in a base fluid delays the onset of convection. Contrary to what is argued by many authors, we show by numerical simulations that the use of nanofluids can reduce the heat transfer rate instead of increasing it.

Pool Boiling Characteristics of Metallic Nanofluids

2011 ◽  
Vol 133 (11) ◽  
Author(s):  
K. Hari Krishna ◽  
Harish Ganapathy ◽  
G. Sateesh ◽  
Sarit K. Das
Keyword(s):  
Heat Transfer ◽  
Thermal Conductivity ◽  
Boiling Heat Transfer ◽  
Volume Fraction ◽  
Pool Boiling ◽  
Heat Fluxes ◽  
Solid Particles ◽  
Heater Surface ◽  
Heat Transfer Characteristics ◽  
Transfer Characteristics

Nanofluids, solid-liquid suspensions with solid particles of size of the order of few nanometers, have created interest in many researchers because of their enhancement in thermal conductivity and convective heat transfer characteristics. Many studies have been done on the pool boiling characteristics of nanofluids, most of which have been with nanofluids containing oxide nanoparticles owing to the ease in their preparation. Deterioration in boiling heat transfer was observed in some studies. Metallic nanofluids having metal nanoparticles, which are known for their good heat transfer characteristics in bulk regime, reported drastic enhancement in thermal conductivity. The present paper investigates into the pool boiling characteristics of metallic nanofluids, in particular of Cu-H2O nanofluids, on flat copper heater surface. The results indicate that at comparatively low heat fluxes, there is deterioration in boiling heat transfer with very low particle volume fraction of 0.01%, and it increases with volume fraction and shows enhancement with 0.1%. However, the behavior is the other way around at high heat fluxes. The enhancement at low heat fluxes is due to the fact that the effect of formation of thin sorption layer of nanoparticles on heater surface, which causes deterioration by trapping the nucleation sites, is overshadowed by the increase in microlayer evaporation, which is due to enhancement in thermal conductivity. Same trend has been observed with variation in the surface roughness of the heater as well.

A Thermal Barrier With Adaptive Heat Transfer Characteristics

1994 ◽  
Vol 116 (2) ◽  
pp. 302-310 ◽  
Author(s):  
P. Furmanski ◽  
J. M. Floryan
Keyword(s):  
Heat Transfer ◽  
Heat Flow ◽  
Volume Fraction ◽  
Large Temperature ◽  
Thermal Barrier ◽  
Heat Transfer Characteristics ◽  
Transfer Characteristics ◽  
Apparent Slip ◽  
Small Volume Fraction ◽  
Relative Thermal Conductivity

A thermal barrier with adaptive heat transfer characteristics for applications in zero gravity environments is considered. The barrier consists of a mixture of fluid with a small volume fraction of arbitrarily oriented, randomly distributed particles of ellipsoidal shape. Heat flux control is obtained by changing the orientation of the particles. Heat flow may be increased up to several hundred times by rotating the particles from being parallel to the walls to being transverse to the walls and by increasing their aspect ratio, volume fraction, and relative thermal conductivity. An increase in the size of the particles results in the appearance of wall effects, which may substantially reduce heat flow as compared to the case of an infinite medium. Very large temperature variation is found to occur near the walls where an apparent “slip” of temperature occurs for barriers whose thickness is large compared to the particle size.

Laminar Flow and Heat Transfer Characteristics of Colloid Suspensions in Water: A Numerical Study

2009 ◽  
Author(s):  
Khalid N. Alammar ◽  
Lin-wen Hu
Keyword(s):  
Heat Transfer ◽  
Laminar Flow ◽  
Heat Transfer Enhancement ◽  
Volume Fraction ◽  
Numerical Study ◽  
Volume Flow Rate ◽  
Transfer Enhancement ◽  
Heat Transfer Characteristics ◽  
Transfer Characteristics ◽  
Flow And Heat Transfer

Numerical analysis is performed to examine axisymmetric laminar flow and heat transfer characteristics of colloidal dispersions of nanoparticles in water (nanofluids). Effect of volume fraction on flow and heat transfer characteristics is investigated. Four different materials, Alumina, Copper, Copper Oxide, and Graphite are considered. Heat transfer and property measurements were conducted previously for Alumina nanofluid. The measurements have shown that nanofluids can behave as homogeneous mixtures. It is found that oxide-based nanofluids offer the least heat transfer enhancement compared to elements-based nanofluids. When normalized by friction pressure drop, it is shown that graphite can have the highest effective heat transfer enhancement. For a given volume flow rate, all nanofluids exhibited linear increase in heat transfer enhancement with increasing colloids volume fraction, up to 0.05.

On the Mathematical Modeling of Heat Transfer Characteristics of Turbulent Flames in Industrial Furnaces

2002 ◽  
Author(s):  
Essam E. Khalil
Keyword(s):  
Mathematical Modeling ◽  
Heat Transfer ◽  
Flow Pattern ◽  
Three Dimensional ◽  
Flow Regimes ◽  
Wall Heat Transfer ◽  
Governing Equations ◽  
Heat Transfer Characteristics ◽  
Combustion Chambers ◽  
Transfer Characteristics

The recent advances in numerical methods and the vast development of computers had directed the designers to better development and modifications to air flow pattern and heat transfer in combustion chambers. Extensive efforts are exerted to adequately predict the air velocity and turbulence intensity distributions in the combustor zones and to reduce the emitted pollution and noise abatement to ultimately produce quite and energy efficient combustor systems. The present work fosters mathematical modeling techniques to primarily predict what happens in three-dimensional combustion chambers simulating boiler furnaces, areo engines in terms of flow regimes and interactions. The present work also demonstrates the effect of chamber design and operational parameters on performance, wall heat transfer under various operating parameters. The governing equations of mass, momentum and energy are commonly expressed in a preset form with source terms to represent pressure gradients, turbulence and viscous action. The physical and chemical characteristics of the air and fuel are obtained from tabulated data in the literature. The flow regimes and heat transfer play an important role in the efficiency and utilization of energy. The results are obtained in this work with the aid of the three-dimensional program 3DCOMB; applied to axisymmetrical and three-dimensional complex geometry with and without swirl with liquid or gaseous fuels. The present numerical grid arrangements cover the combustion chamber in the X, R or Y and Z coordinates directions. The numerical residual in the governing equations is typically less than 0.001%. The obtained results include velocity vectors, turbulence intensities and wall heat transfer distributions in combusors. Examples of large industrial furnaces are shown and are in good agreement with available measurements in the open literature. One may conclude that flow patterns, turbulence and heat transfer in combustors are strongly affected by the inlet swirl, inlet momentum ratios, combustor geometry. Both micro and macro mixing levels are influential. The present modeling capabilities can adequately predict the local flow pattern and heat transfer characteristics in Complex combustors. Proper representation of the heat transfer and radiation flux is important in adequate predictions of large furnace performance.

Numerical Investigation of Free Convection in a Porous Corrugated Cavity Filled With Silver (Ag) Dispersed Nano-Fluid

2020 ◽  
Vol 13 (4) ◽  
Author(s):  
Saurabh Bhardwaj ◽  
Amaresh Dalal
Keyword(s):  
Heat Transfer ◽  
Volume Fraction ◽  
Solid Volume Fraction ◽  
Uniform Heating ◽  
Heat Transfer Characteristics ◽  
Closed Cavity ◽  
Transfer Characteristics ◽  
Nano Fluid ◽  
Increasing Trend ◽  
Irregular Motion

Abstract The present work examines the convective heat transfer characteristics in a two-dimensional (2D) corrugated closed cavity embedded with porous media. The cavity is considered to be filled with silver dispersed water-based nano-fluid. The bottom wall is heated uniformly and non-uniformly in two different cases keeping both side corrugated walls isothermally cold with an adiabatic top wall. The various parameters are selected to perform numerical simulation in the range of solid-volume fraction, 0% ≤ ϕ ≤ 10%, 103 ≤ Ra ≤ 106, and 10−4 ≤ Da ≤ 10−2. The investigation shows that the heat transfer rate shows an increasing trend at high values of Ra and Da due to strong buoyancy forces in uniform and non-uniform heating. However, an increase in heat transfer in uniform heating is more compared to non-uniform heating. It is also observed that the nano-fluid has a great impact on the heat transfer characteristics due to its high value of thermal conductivity and irregular motion of the particles. As a result, the average Nusselt number (Nuavg) shows an increasing trend for increasing solid-volume fraction values.

Sign in / Sign up

Export Citation Format

Share Document