scholarly journals Elastic Reverse-Time Migration with Complex Topography

Energies ◽  
2021 ◽  
Vol 14 (23) ◽  
pp. 7837
Author(s):  
Yu Zhong ◽  
Hanming Gu ◽  
Yangting Liu ◽  
Qinghui Mao
Keyword(s):  
Surface Topography ◽  
Seismic Data ◽  
Wave Equations ◽  
Oil And Gas ◽  
Complex Topography ◽  
Reverse Time ◽  
Reverse Time Migration ◽  
S Waves ◽  
Time Migration ◽  
Multicomponent Seismic

Migration is an important step in seismic data processing for oil and gas exploration. The accuracy of migration directly affects the accuracy of subsequent oil and gas reservoir characterization. Reverse-time migration is one of the most accurate migration methods at present. Multi-wave and multicomponent seismic data contain more P- and S-wave information. Making full use of multi-wave and multicomponent seismic data can offer more information about underground structure and lithology, as well as improve the accuracy of seismic exploration. Elastic reverse-time migration (ERTM) has no dip restriction and can be applied to image multi-wave and multicomponent seismic data in complex structural areas and some special lithology structures. However, the surface topography of complex regions has an influence on wavefield and seriously degrades the quality of ERTM’s migration results. We developed a new ERTM method to migrate multi-wave and multicomponent seismic data in the region with complex surface topography. We first fill the layers between the highest and lowest undulating surface with near-surface elastic parameters in a complex topography model to obtain a new model with a horizontal surface. This allows the finite difference (FD) method based on the regular rectangular grid to be used to numerically solve elastic wave equations in the model with complex topography. The decoupled wave equations are used to generate source P- and S-waves and receiver P- and S-waves to reduce crosstalk artefacts in ERTM. A topography-related filter is further used to remove the influence of surface topography on migration results. The scalar imaging condition is also applied to generate PP and PS migration images. Some numerical examples with different complex topographies demonstrate that our proposed ERTM method can remove the influence of complex topography on ERTM’s images and effectively generate high-quality ERTM images.

Vector-wave-based elastic reverse time migration of ocean-bottom 4C seismic data

Geophysics ◽  
2018 ◽  
Vol 83 (4) ◽  
pp. S333-S343 ◽  
Author(s):  
Pengfei Yu ◽  
Jianhua Geng ◽  
Jiqiang Ma
Keyword(s):  
Seismic Data ◽  
Ocean Bottom ◽  
Reverse Time ◽  
Reverse Time Migration ◽  
S Wave ◽  
Vector Wave ◽  
S Waves ◽  
Time Migration ◽  
Multicomponent Seismic ◽  
Wavefield Extrapolation

The acoustic-elastic coupled equation (AECE) has several advantages when compared with conventional scalar-wave-based elastic reverse time migration (ERTM) methods used to image ocean-bottom multicomponent seismic data. In particular, vector-wave-based ERTM requires vectorial P- and S-waves on the source and receiver sides, but these cannot be directly obtained from wavefield extrapolation using AECE. Therefore, we have developed a P- and S-wave vector decomposition (VD) approach within AECE; this approach enables the deduction of a novel VD-based AECE, from which vectorial P- and S-waves can be obtained directly via wavefield extrapolation. We are also able to derive a new formulation suitable for vector-wave-based ERTM of ocean-bottom multicomponent seismic data that can generate a phase-preserved PS-image. Three synthetic examples illustrate the validity and effectiveness of our new method.

Elastic least-squares reverse time migration of steeply dipping structures using prismatic reflections

Geophysics ◽  
2022 ◽  
pp. 1-130
Author(s):  
Zheng Wu ◽  
Yuzhu Liu ◽  
Jizhong Yang
Keyword(s):  
Least Squares ◽  
Seismic Data ◽  
Oil And Gas ◽  
Normal Equation ◽  
Reverse Time ◽  
Reverse Time Migration ◽  
S Wave ◽  
Time Migration ◽  
Multicomponent Seismic ◽  
Imaging Conditions

The migration of prismatic reflections can be used to delineate steeply dipping structures, which is crucial for oil and gas exploration and production. Elastic least-squares reverse time migration (ELSRTM), which considers the effects of elastic wave propagation, can be used to obtain reasonable subsurface reflectivity estimations and interpret multicomponent seismic data. In most cases, we can only obtain a smooth migration model. Thus, conventional ELSRTM, which is based on the first-order Born approximation, considers only primary reflections and cannot resolve steeply dipping structures. To address this issue, we develop an ELSRTM framework, called Pris-ELSRTM, which can jointly image primary and prismatic reflections in multicomponent seismic data. When Pris-ELSRTM is directly applied to multicomponent records, near-vertical structures can be resolved. However, the application of imaging conditions established for prismatic reflections to primary reflections destabilizes the process and leads to severe contamination of the results. Therefore, we further improve the Pris-ELSRTM framework by separating prismatic reflections from recorded multicomponent data. By removing artificial imaging conditions from the normal equation, primary and prismatic reflections can be imaged based on unique imaging conditions. The results of synthetic tests and field data applications demonstrate that the improved Pris-ELSRTM framework produces high-quality images of steeply dipping P- and S-wave velocity structures. However, it is difficult to delineate steep density structures because of the insensitivity of the density to prismatic reflections.

2D least-squares elastic reverse time migration of multicomponent seismic data

Geophysics ◽  
2019 ◽  
Vol 84 (6) ◽  
pp. S523-S538 ◽  
Author(s):  
Bingluo Gu ◽  
Jianguang Han ◽  
Zhiming Ren ◽  
Zhenchun Li
Keyword(s):  
Least Squares ◽  
Seismic Data ◽  
Signal To Noise Ratio ◽  
Adjoint Operator ◽  
Reverse Time ◽  
Reverse Time Migration ◽  
Time Migration ◽  
Multicomponent Seismic ◽  
Isotropic Media ◽  
Wavefield Decomposition

Elastic reverse time migration (ERTM) is a state-of-the-art imaging technique used for determining complicated subsurface structures. However, the migrated images often suffer from low spatial resolution, low signal-to-noise ratio (S/N), and unbalanced amplitudes because the theoretical hypothesis of ERTM cannot be satisfied in practice. Although elastic least-squares reverse time migration (ELSRTM) has been proposed to address the issues of ERTM, the resulting images are generally represented by parameter perturbations such as P- and S-velocity perturbations, which have the different physical meanings from the ERTM images. To produce improved ERTM images, we used a least-squares RTM method for elastic data in isotropic media by applying least-squares inversion to ERTM. In the least-squares ERTM method, the forward operator generates multicomponent seismic data from the migrated images by applying elastic wavefield decomposition, scalar wavefield extrapolation, and wavefield recomposition operators. Additionally, the adjoint operator generates PP and PS images using ERTM, at which point the wavefield decomposition operator and scalar imaging condition are applied in the imaging process. Compared to conventional ERTM, our least-squares ERTM method enables us to produce improved ERTM images with higher resolution, more balanced amplitudes, and fewer artifacts. Several synthetic and field data examples were used to validate the effectiveness of the proposed least-squares ERTM method.

Elastic least-squares reverse time migration based on decoupled wave equations

Geophysics ◽  
2021 ◽  
pp. 1-72
Author(s):  
Yu Zhong ◽  
Hanming Gu ◽  
Yangting Liu ◽  
QingHui Mao
Keyword(s):  
Least Squares ◽  
Wave Equations ◽  
Wave Mode ◽  
Reverse Time ◽  
Reverse Time Migration ◽  
S Waves ◽  
Limited Bandwidth ◽  
Time Migration ◽  
Adjoint State ◽  
Isotropic Media

Elastic reverse time migration (ERTM) is developed for better characterization of complex structures by imaging multicomponent seismic data. However, conventional ERTM is subject to limitations such as finite recording aperture, limited bandwidth, and imperfect illumination. Elastic least-squares reverse time migration (ELSRTM) can improve imaging accuracy gradually with iterations by minimizing the residuals between observed and calculated multicomponent data. Conventional ELSRTM suffers from crosstalk artifacts caused by coupled elastic wavefields with different wave modes. Decomposing the coupled elastic wavefields into pure P- and S-waves is an effective method to suppress these crosstalk artifacts. Considering the trade-off between calculation accuracy and efficiency, we have developed a new ELSRTM scheme for isotropic media based on decoupled wave equations to suppress these wave mode-related crosstalk artifacts in the images of conventional ELSRTM. Pure wavefields are obtained by solving the decoupled wave equations using the finite-difference (FD) method in our new ELSRTM method. We also derive new decoupled adjoint-state wave equations, which are suitable for the elastic velocity-stress equations in isotropic media. We further propose the gradient equations based on pure wavefields to update the reflectivity images. Synthetic examples demonstrate that our new ELSRTM method can generate images that better represent the subsurface when compared with conventional ERTM and conventional ELSRTM.

Q least-squares reverse time migration based on the first-order viscoacoustic quasidifferential equations

Geophysics ◽  
2021 ◽  
pp. 1-65
Author(s):  
Yingming Qu ◽  
Yixin Wang ◽  
Zhenchun Li ◽  
Chang Liu
Keyword(s):  
Wave Equation ◽  
Least Squares ◽  
Surface Topography ◽  
Density Perturbation ◽  
Second Order ◽  
Reverse Time ◽  
Reverse Time Migration ◽  
First Order ◽  
Time Migration ◽  
Grid Scheme

Seismic wave attenuation caused by subsurface viscoelasticity reduces the quality of migration and the reliability of interpretation. A variety of Q-compensated migration methods have been developed based on the second-order viscoacoustic quasidifferential equations. However, these second-order wave-equation-based methods are difficult to handle with density perturbation and surface topography. In addition, the staggered grid scheme, which has an advantage over the collocated grid scheme because of its reduced numerical dispersion and enhanced stability, works in first-order wave-equation-based methods. We have developed a Q least-squares reverse time migration method based on the first-order viscoacoustic quasidifferential equations by deriving Q-compensated forward-propagated operators, Q-compensated adjoint operators, and Q-attenuated Born modeling operators. Besides, our method using curvilinear grids is available even when the attenuating medium has surface topography and can conduct Q-compensated migration with density perturbation. The results of numerical tests on two synthetic and a field data sets indicate that our method improves the imaging quality with iterations and produces better imaging results with clearer structures, higher signal-to-noise ratio, higher resolution, and more balanced amplitude by correcting the energy loss and phase distortion caused by Q attenuation. It also suppresses the scattering and diffracted noise caused by the surface topography.

Near-Borehole Imaging Using Full-Waveform Sonic Data

2021 ◽  
Author(s):  
Hala Alqatari ◽  
Thierry-Laurent Tonellot ◽  
Mohammed Mubarak
Keyword(s):  
Seismic Data ◽  
Reverse Time ◽  
Reverse Time Migration ◽  
Full Waveform ◽  
Time Migration ◽  
Imaging Results ◽  
High Resolution Images ◽  
Recorded Data ◽  
The Impact ◽  
Processing Steps

Abstract This work presents a full waveform sonic (FWS) dataset processing to generate high-resolution images of the near-borehole area. The dataset was acquired in a nearly horizontal well over a distance of 5400 feet. Multiple formation boundaries can be identified on the final image and tracked at up to 200 feet deep, along the wellbore's trajectory. We first present a new preprocessing sequence to prepare the sonic data for imaging. This sequence leverages denoising algorithms used in conventional surface seismic data processing to remove unwanted components of the recorded data that could harm the imaging results. We then apply a reverse time migration algorithm to the data at different processing stages to assess the impact of the main processing steps on the final image.

Some Aspects of Seismic Data Reverse Time Migration for Salt Tectonics Geology of the Dnieper-Donets Basin

2021 ◽  
Author(s):  
Pavlo Kuzmenko ◽  
Viktor Buhrii ◽  
Carlo D'Aguanno ◽  
Viktor Maliar ◽  
Hrigorii Kashuba ◽  
...  
Keyword(s):  
Seismic Data ◽  
Full Range ◽  
Donets Basin ◽  
Salt Tectonics ◽  
Imaging Method ◽  
Reverse Time ◽  
Reverse Time Migration ◽  
Time Migration ◽  
Seismic Image ◽  
Complex Geology

Abstract Processing of the seismic data acquired in areas of complex geology of the Dnieper-Donets basin, characterized by the salt tectonics, requires special attention to the salt dome interpretation. For this purpose, Kirchhoff Depth Imaging and Reverse Time Migration (RTM) were applied and compared. This is the first such experience in the Dnieper-Donets basin. According to international experience, RTM is the most accurate seismic imaging method for steep and vertical geological (acoustic contrast) boundaries. Application of the RTM on 3D WAZ land data is a great challenge in Dnieper-Donets Basin because of the poor quality of the data with a low signal-to-noise ratio and irregular spatial sampling due to seismic acquisition gaps and missing traces. The RTM algorithm requires data, organized to native positions of seismic shots. For KPSDM we used regularized data after 5D interpolation. This affects the result for near salt reflection. The analysis of KPSDM and RTM results for the two areas revealed the same features. RTM seismic data looked more smoothed, but for steeply dipping reflections, lateral continuity of reflections was much improved. The upper part (1000 m) of the RTM has shadow zones caused by low fold. Other differences between Kirchhoff data and RTM are in the spectral content, as the former is characterized by the full range of seismic frequency spectrum. Conversely, beneath the salt, the RTM has reflections with steep dips which are not observed on the KPSDM. It is possible to identify new prospects using the RTM seismic image. Reverse Time Migration of 3D seismic data has shown geologically consistent results and has the potential to identify undiscovered hydrocarbon traps and to improve salt flank delineation in the complex geology of the Dnieper-Donets Basin's salt domes.

Sign in / Sign up

Export Citation Format

Share Document