scholarly journals Modelling and Feasibility Study on Using Tidal Power with an Energy Storage Utility for Residential Needs

Inventions ◽  
2019 ◽  
Vol 4 (1) ◽  
pp. 11
Author(s):  
Gianmaria Giannini
Keyword(s):  
Energy Storage ◽  
Thermal Energy ◽  
Energy Demand ◽  
Tidal Energy ◽  
Hot Water ◽  
Energy Output ◽  
Mature Stage ◽  
Tidal Power ◽  
Potential Cost ◽  
Storage Facilities

Tidal power technology is at its mature stage and large deployments are soon expected. The characteristics of tidal energy and its advantage to be predictable make it an ideal type of resource to be coupled with energy storage facilities. Despite this, most energy storage facilities are expensive. The fact that water has a high specific heat capacity makes this a potential cost-effective medium to be used for storing large amounts of thermal energy for balancing renewable energy output. This paper is an investigation on the possible application of integrating hot water reservoirs for storing tidal energy during power output peaks for domestic use. The main objective of this study is to evaluate the major factors incident on the proposed solution and to provide considerations on which real remunerations the proposed idea could bring to communities or to single families. For this purpose, a simplified numerical analysis, concerning three different scenarios, was performed. These scenarios differ by type of buildings and type of thermal energy demand. The study mainly concerns remote communities. Findings indicated that the proposed idea is technically feasible and if applied in the context of residential compounds, this could be more attractive in economic terms.

A Geothermal Energy Concept based on Heat Storage in Geological Media

2021 ◽  
Author(s):  
Rubén Vidal ◽  
Maarten W. Saaltink ◽  
Sebastià Olivella
Keyword(s):  
Energy Storage ◽  
Thermal Energy ◽  
Thermal Energy Storage ◽  
Energy Demand ◽  
Ground Deformation ◽  
Hot Water ◽  
Energy Deficit ◽  
Good Tool ◽  
Aquifer Thermal Energy Storage ◽  
Low Efficiency

<p>Aquifer Thermal Energy Storage (ATES) can help to balance energy demand and supply to make better use of infrastructures and resources. ATES consists of a pair or more wells that simultaneously inject or extract thermal energy into aquifers. The aim of ATES is to store the excess of energy during summer and to reuse it during winter, when there is an energy deficit. High-temperature Aquifer Thermal Energy Storage (HT-ATES) provides a good option to store water over 50°C, but it requires facing some problems, such as low efficiency recoveries and the uplift of the surface. Coupled thermo-hydro-mechanical (THM) modelling is a good tool to analyze the viability and cost effectiveness of the HT-ATES systems and understand the interaction of processes, such as heat flux, groundwater flow and ground deformation. We present the 3D THM modelling of a pilot HT-ATES system, inspired by one of the projects of HEATSTORE, which is a GEOTHERMICA ERA-NET co-funded project. The model aims to simulate the injection of hot water of 90°C in a central well and the extraction of water in four auxiliary wells during summer. In winter, the auxiliary wells inject water of 50°C and the central well extract water. The loading lasts longer than the unloading (8 months versus 4 months) and overall more heat is injected than extracted. We found that the system is more efficient in terms of energy recovery, the more years the system is operating. In the aquifer, both thermal loads and hydraulic loads have an important role in terms of displacements. At the surface, the vertical displacements are only a consequence of the hydraulic strains generated by the injection of water in the aquifer.</p>

Thermoeconomic Cost Analysis of Central Solar Heating Plants Combined With Seasonal Storage

2010 ◽  
Author(s):  
Miguel A. Lozano ◽  
Antonio Anastasia ◽  
Luis M. Serra ◽  
Vittorio Verda
Keyword(s):  
Energy Storage ◽  
Cost Analysis ◽  
Thermal Energy ◽  
Thermal Energy Storage ◽  
Energy Demand ◽  
District Heating ◽  
Solar Heating ◽  
Hot Water ◽  
The European Union ◽  
Internal Flows

The European Union and its Member States have committed themselves to achieving a 20% share of renewable energy by 2020. If the focus remains solely on solar thermal systems for domestic hot water (DHW) preparation, as in Spain, then the solar contribution will be very limited. Central Solar Heating Plants combined with Seasonal Storage (CSHPSS) systems enable high solar fractions of 50% and more. Most CSHPSS demonstration plants in Europe have been built in Central and North Europe, mainly in Denmark, Germany and Sweden. South Europe has little experience. This article presents a thermoeconomic cost analysis of CSHPSS systems. The objective of thermoeconomics is to explain the cost formation process of internal flows and products of energy systems. The costs obtained with thermoeconomics can be used to optimize the design of new plants and to control the production of existing plants. A simulation study on solar assisted district heating systems with high solar fractions and seasonal thermal energy storage was carried out with TRNSYS taking into consideration the meteorological conditions in Zaragoza (Spain). A CSHPSS plant was designed for a district of 500 dwellings with an annual thermal energy demand of 2,905 MWh/year. The process of cost formation has been analyzed considering the very specific features of the CSHPSS designed system: free solar energy, seasonal and DHW thermal energy storage, continuous variation of the operation due to highly variations of solar radiation and energy demands (hourly and seasonal). These features impose important difficulties in the calculation of the costs of internal flows and products in this type of systems.

scholarly journals Comparison of Direct and Indirect Active Thermal Energy Storage Strategies for Large-Scale Solar Heating Systems

Energies ◽  
2019 ◽  
Vol 12 (10) ◽  
pp. 1948 ◽  
Author(s):  
Xiaofeng Guo ◽  
Alain Pascal Goumba ◽  
Cheng Wang
Keyword(s):  
Energy Storage ◽  
Thermal Energy ◽  
Thermal Energy Storage ◽  
Energy Demand ◽  
Large Scale ◽  
Solar Heating ◽  
Hot Water ◽  
Simplified Algorithm ◽  
Change Material

Large-scale solar heating for the building sector requires an adequate Thermal Energy Storage (TES) strategy. TES plays the role of load shifting between the energy demand and the solar irradiance and thus makes the annual production optimal. In this study, we report a simplified algorithm uniquely based on energy flux, to evaluate the role of active TES on the annual performance of a large-scale solar heating for residential thermal energy supply. The program considers different types of TES, i.e., direct and indirect, as well as their specifications in terms of capacity, storage density, charging/discharging limits, etc. Our result confirms the auto-regulation ability of indirect (latent using Phase Change Material (PCM), or Borehole thermal storage (BTES) in soil) TES which makes the annual performance comparable to that of direct (sensible with hot water) TES. The charging and discharging restrictions of the latent TES, until now considered as a weak point, could retard the achievement of fully-charged situation and prolong the charging process. With its compact volume, the indirect TES turns to be promising for large-scale solar thermal application.

scholarly journals Effect of Twisted Fin Array in a Triple-Tube Latent Heat Storage System during the Charging Mode

2021 ◽  
Vol 13 (5) ◽  
pp. 2685
Author(s):  
Mohammad Ghalambaz ◽  
Jasim M. Mahdi ◽  
Amirhossein Shafaghat ◽  
Amir Hossein Eisapour ◽  
Obai Younis ◽  
...  
Keyword(s):  
Energy Storage ◽  
Heat Exchanger ◽  
Latent Heat ◽  
Thermal Energy ◽  
Heat Storage ◽  
Hot Water ◽  
Melting Time ◽  
Latent Heat Storage ◽  
Tube Heat Exchanger ◽  
Storage Rate

This study aims to assess the effect of adding twisted fins in a triple-tube heat exchanger used for latent heat storage compared with using straight fins and no fins. In the proposed heat exchanger, phase change material (PCM) is placed between the middle annulus while hot water is passed in the inner tube and outer annulus in a counter-current direction, as a superior method to melt the PCM and store the thermal energy. The behavior of the system was assessed regarding the liquid fraction and temperature distributions as well as charging time and energy storage rate. The results indicate the advantages of adding twisted fins compared with those of using straight fins. The effect of several twisted fins was also studied to discover its effectiveness on the melting rate. The results demonstrate that deployment of four twisted fins reduced the melting time by 18% compared with using the same number of straight fins, and 25% compared with the no-fins case considering a similar PCM mass. Moreover, the melting time for the case of using four straight fins was 8.3% lower than that compared with the no-fins case. By raising the fins’ number from two to four and six, the heat storage rate rose 14.2% and 25.4%, respectively. This study presents the effects of novel configurations of fins in PCM-based thermal energy storage to deliver innovative products toward commercialization, which can be manufactured with additive manufacturing.

scholarly journals Self-Sufficiency and Energy Savings of Renewable Thermal Energy Systems for an Energy-Sharing Community

Energies ◽  
2021 ◽  
Vol 14 (14) ◽  
pp. 4284
Author(s):  
Min-Hwi Kim ◽  
Youngsub An ◽  
Hong-Jin Joo ◽  
Dong-Won Lee ◽  
Jae-Ho Yun
Keyword(s):  
Renewable Energy ◽  
Energy Storage ◽  
Thermal Energy ◽  
Thermal Energy Storage ◽  
Energy Systems ◽  
Hot Water ◽  
Pump System ◽  
Ground Source Heat Pumps ◽  
Self Sufficiency ◽  
Energy Sharing

Due to increased grid problems caused by renewable energy systems being used to realize zero energy buildings and communities, the importance of energy sharing and self-sufficiency of renewable energy also increased. In this study, the energy performance of an energy-sharing community was investigated to improve its energy efficiency and renewable energy self-sufficiency. For a case study, a smart village was selected via detailed simulation. In this study, the thermal energy for cooling, heating, and domestic hot water was produced by ground source heat pumps, which were integrated with thermal energy storage (TES) with solar energy systems. We observed that the ST system integrated with TES showed higher self-sufficiency with grid interaction than the PV and PVT systems. This was due to the heat pump system being connected to thermal energy storage, which was operated as an energy storage system. Consequently, we also found that the ST system had a lower operating energy, CO2 emissions, and operating costs compared with the PV and PVT systems.

Analysis of Thermal Energy Storage to a Combined Heat and Power Plant

2021 ◽  
Vol 9 (9) ◽  
pp. 1313-1320
Author(s):  
Shahim Nisar
Keyword(s):  
Energy Storage ◽  
Thermal Energy ◽  
Thermal Energy Storage ◽  
Energy Demand ◽  
Power Plants ◽  
Heat Storage ◽  
Packed Bed ◽  
Water Tank ◽  
Latent Heat Storage ◽  
Storage Methods

Abstract: Thermal energy storage (TES) is a technology that stocks thermal energy by heating or cooling a storage medium so that the stored energy can be used at a later time for heating and cooling applications and power generation. TES systems are used particularly in buildings and in industrial processes. This paper is focused on TES technologies that provide a way of valorizing solar heat and reducing the energy demand of buildings. The principles of several energy storage methods and calculation of storage capacities are described. Sensible heat storage technologies, including water tank, underground and packed-bed storage methods, are briefly reviewed. Additionally, latent-heat storage systems associated with phase-change materials for use in solar heating/cooling of buildings, solar water heating, heat-pump systems, and concentrating solar power plants as well as thermo-chemical storage are discussed. Finally, cool thermal energy storage is also briefly reviewed and outstanding information on the performance and costs of TES systems are included.

scholarly journals Energy and Exergy Analysis of Sensible Thermal Energy Storage—Hot Water Tank for a Large CHP Plant in Poland

Energies ◽  
2020 ◽  
Vol 13 (18) ◽  
pp. 4842 ◽  
Author(s):  
Ryszard Zwierzchowski ◽  
Marcin Wołowicz
Keyword(s):  
Energy Storage ◽  
Ambient Temperature ◽  
Thermal Energy ◽  
Thermal Energy Storage ◽  
Exergy Analysis ◽  
Hot Water ◽  
Water Tank ◽  
Exergy Destruction ◽  
Energy And Exergy ◽  
Energy And Exergy Analysis

The paper contains a simplified energy and exergy analysis of pumps and pipelines system integrated with Thermal Energy Storage (TES). The analysis was performed for a combined heat and power plant (CHP) supplying heat to the District Heating System (DHS). The energy and exergy efficiency for the Block Part of the Siekierki CHP Plant in Warsaw was estimated. CHP Plant Siekierki is the largest CHP plant in Poland and the second largest in Europe. The energy and exergy analysis was executed for the three different values of ambient temperature. It is according to operation of the plant in different seasons: winter season (the lowest ambient temperature Tex = −20 °C, i.e., design point conditions), the intermediate season (average ambient temperature Tex = 1 °C), and summer (average ambient temperature Tex = 15 °C). The presented results of the analysis make it possible to identify the places of the greatest exergy destruction in the pumps and pipelines system with TES, and thus give the opportunity to take necessary improvement actions. Detailed results of the energy-exergy analysis show that both the energy consumption and the rate of exergy destruction in relation to the operation of the pumps and pipelines system of the CHP plant with TES for the tank charging and discharging processes are low.

scholarly journals Thermal energy storage (TES) technology for active and passive cooling in buildings: A Review

2018 ◽  
Vol 225 ◽  
pp. 03022
Author(s):  
Nursyazwani Abdul Aziz ◽  
Nasrul Amri Mohd Amin ◽  
Mohd Shukry Abd Majid ◽  
Izzudin Zaman
Keyword(s):  
Energy Storage ◽  
Energy Management ◽  
Thermal Energy ◽  
Thermal Energy Storage ◽  
Energy Demand ◽  
Supply And Demand ◽  
Storage System ◽  
Passive Cooling ◽  
Building Sector ◽  
Advantages And Disadvantages

Thermal energy storage (TES) system is one of the outstanding technologies available contributes for achieving sustainable energy demand. The energy storage system has been proven capable of narrowing down the energy mismatch between energy supply and demand. The thermal energy storage (TES) - buildings integration is expected to minimize the energy demand shortage and also offers for better energy management in building sector. This paper presents a state of art of the active and passive TES technologies integrated in the building sector. The integration method, advantages and disadvantages of both techniques were discussed. The TES for low energy building is inevitably needed. This study prescribes that the integration of TES system for both active and passive cooling techniques are proven to be beneficial towards a better energy management in buildings.

Sign in / Sign up

Export Citation Format

Share Document