scholarly journals Conduction-Based Thermally Assisted Micromilling Process for Cutting Difficult-to-Machine Materials

2020 ◽  
Vol 4 (2) ◽  
pp. 34 ◽  
Author(s):  
Timo Platt ◽  
Alexander Meijer ◽  
Dirk Biermann
Keyword(s):  
Tool Wear ◽  
High Speed ◽  
End Milling ◽  
High Speed Steel ◽  
High Strength ◽  
Process Conditions ◽  
Manufacturing Processes ◽  
Central Process ◽  
Workpiece Temperature ◽  
Micro End Milling

The increasing demand for complex and wear-resistant forming tools made of difficult-to-machine materials requires efficient manufacturing processes. In terms of high-strength materials; highly suitable processes such as micromilling are limited in their potential due to the increased tool loads and the resulting tool wear. This promotes hybrid manufacturing processes that offer approaches to increase the performance. In this paper; conduction-based thermally assisted micromilling using a prototype device to homogeneously heat the entire workpiece is investigated. By varying the workpiece temperature by 20 °C < TW < 500 °C; a highly durable high-speed steel (HSS) AISI M3:2 (63 HRC) and a hot-work steel (HWS) AISI H11 (53 HRC) were machined using PVD-TiAlN coated micro-end milling tools (d = 1 mm). The influence of the workpiece temperature on central process conditions; such as tool wear and achievable surface quality; are determined. As expected; the temporary thermal softening of the materials leads to a reduction in the cutting forces and; thus; in the resulting tool wear for specific configurations of the thermal assistance. While only minor effects are detected regarding the surface topography; a significant reduction in the burr height is achieved.

CYCLOPS BHT

Alloy Digest ◽  
1965 ◽  
Vol 14 (2) ◽  
Keyword(s):  
Fracture Toughness ◽  
Corrosion Resistance ◽  
Elevated Temperature ◽  
High Speed ◽  
High Speed Steel ◽  
High Strength ◽  
Heat Treating ◽  
High Load ◽  
Structural Components ◽  
Temperature Performance

Abstract Cyclops BHT is a low-alloy martensitic high-speed steel of the molybdenum type recommended for high strength, high load structural components designed for elevated temperature service. This datasheet provides information on composition, physical properties, hardness, elasticity, and tensile properties as well as fracture toughness. It also includes information on high temperature performance and corrosion resistance as well as forming, heat treating, machining, and joining. Filing Code: SA-173. Producer or source: Cyclops Corporation.

VASCO M-50

Alloy Digest ◽  
1974 ◽  
Vol 23 (11) ◽  
Keyword(s):  
Elevated Temperature ◽  
Physical Properties ◽  
Surface Treatment ◽  
High Speed ◽  
High Speed Steel ◽  
High Strength ◽  
Heat Treating ◽  
High Load ◽  
Aisi 52100 ◽  
Aisi 52100 Steel

Abstract VASCO M-50 is a hardenable (martensitic), low-alloy high-speed steel developed primarily for high-strength, high-load components (such as bearings and gears) designed for elevated-temperature service. It may be used at temperatures up to 600 F; this is in contrast to AISI 52100 steel which may be used up to only 350 F. This datasheet provides information on composition, physical properties, hardness, and elasticity. It also includes information on forming, heat treating, machining, joining, and surface treatment. Filing Code: TS-278. Producer or source: Teledyne Vasco.

Investigation of Surface Roughness and Material Removal Rate for High Speed Micro End Milling on PMMA

2015 ◽  
Vol 1115 ◽  
pp. 12-15
Author(s):  
Nur Atiqah ◽  
Mohammad Yeakub Ali ◽  
Abdul Rahman Mohamed ◽  
Md. Sazzad Hossein Chowdhury
Keyword(s):  
Surface Roughness ◽  
Material Removal Rate ◽  
Feed Rate ◽  
Material Removal ◽  
High Speed ◽  
End Milling ◽  
Removal Rate ◽  
Spindle Speed ◽  
Depth Of Cut ◽  
Micro End Milling

Micro end milling is one of the most important micromachining process and widely used for producing miniaturized components with high accuracy and surface finish. This paper present the influence of three micro end milling process parameters; spindle speed, feed rate, and depth of cut on surface roughness (Ra) and material removal rate (MRR). The machining was performed using multi-process micro machine tools (DT-110 Mikrotools Inc., Singapore) with poly methyl methacrylate (PMMA) as the workpiece and tungsten carbide as its tool. To develop the mathematical model for the responses in high speed micro end milling machining, Taguchi design has been used to design the experiment by using the orthogonal array of three levels L18 (21×37). The developed models were used for multiple response optimizations by desirability function approach to obtain minimum Ra and maximum MRR. The optimized values of Ra and MRR were 128.24 nm, and 0.0463 mg/min, respectively obtained at spindle speed of 30000 rpm, feed rate of 2.65 mm/min, and depth of cut of 40 μm. The analysis of variance revealed that spindle speeds are the most influential parameters on Ra. The optimization of MRR is mostly influence by feed rate. Keywords:Micromilling,surfaceroughness,MRR,PMMA

Experimental investigation of top burr formation in high-speed micro-end milling of titanium alloy

2018 ◽  
Vol 22 (6) ◽  
pp. 989-1011 ◽  
Author(s):  
Chakradhar Bandapalli ◽  
Kundan Kumar Singh ◽  
Bharatkumar Mohanbhai Sutaria ◽  
Dhananjay Vishnuprasad Bhatt
Keyword(s):  
Experimental Investigation ◽  
Titanium Alloy ◽  
High Speed ◽  
End Milling ◽  
Burr Formation ◽  
Micro End Milling

scholarly journals Prediction of Tool Lifetime and Surface Roughness for Nickel-Based Waspaloy

2020 ◽  
Vol 2020 ◽  
pp. 1-12
Author(s):  
Shao-Hsien Chen ◽  
Chung-An Yu
Keyword(s):  
Surface Roughness ◽  
Tool Wear ◽  
High Speed ◽  
Cutting Speed ◽  
High Strength ◽  
Cutting Parameters ◽  
Experimental Results ◽  
Predictive Values ◽  
Actual Surface ◽  
Wide Range

In recent years, most of nickel-based materials have been used in aircraft engines. Nickel-based materials applied in the aerospace industry are used in a wide range of applications because of their strength and rigidity at high temperature. However, the high temperatures and high strength caused by the nickel-based materials during cutting also reduce the tool lifetime. This research aims to investigate the tool wear and the surface roughness of Waspaloy during cutting with various cutting speeds, feed per tooth, cutting depth, and other cutting parameters. Then, it derives the formula for the tool lifetime based on the experimental results and explores the impacts of these cutting parameters on the cutting of Waspaloy. Since the impacts of cutting speed on the cutting of Waspaloy are most significant in accordance with the experimental results, the high-speed cutting is not recommended. In addition, the actual surface roughness of Waspaloy is worse than the theoretical surface roughness in case of more tool wear. Finally, a set of mathematical models can be established based on these results, in order to predict the surface roughness of Waspaloy cut with a worn tool. The errors between the predictive values and the actual values are 5.122%∼8.646%. If the surface roughness is within the tolerance, the model can be used to predict the residual tool lifetime before the tool is damaged completely. The errors between the predictive values and the actual values are 8.014%∼20.479%.

High speed steel tool wear studies in machining of glass-fibre-reinforced plastics

Wear ◽  
1989 ◽  
Vol 132 (2) ◽  
pp. 327-336 ◽  
Author(s):  
G. Santhanakrishnan ◽  
R. Krishnamurthy ◽  
S.K. Malhotra
Keyword(s):  
Tool Wear ◽  
Glass Fibre ◽  
High Speed ◽  
High Speed Steel ◽  
Reinforced Plastics ◽  
Steel Tool ◽  
Glass Fibre Reinforced ◽  
Glass Fibre Reinforced Plastics
Sign in / Sign up

Export Citation Format

Share Document