scholarly journals Pyrolysis Kinetic Properties of Thermal Insulation Waste Extruded Polystyrene by Multiple Thermal Analysis Methods

Materials ◽  
2020 ◽  
Vol 13 (24) ◽  
pp. 5595
Author(s):  
Ang Li ◽  
Wenlong Zhang ◽  
Juan Zhang ◽  
Yanming Ding ◽  
Ru Zhou
Keyword(s):  
Reaction Mechanism ◽  
Thermal Insulation ◽  
Conversion Rate ◽  
Model Fitting ◽  
Pso Algorithm ◽  
Energy Utilization ◽  
Kinetic Properties ◽  
Insulation Material ◽  
Heating Rates ◽  
Model Free

Extruded polystyrene (XPS) is a thermal insulation material extensively applied in building systems. It has attracted much attention because of outstanding thermal insulation performance, obvious flammability shortcoming and potential energy utilization. To establish the reaction mechanism of XPS’s pyrolysis, thermogravimetric experiments were performed at different heating rates in nitrogen, and multiple methods were employed to analyze the major kinetics of pyrolysis. More accurate kinetic parameters of XPS were estimated by four common model-free methods. Then, three model-fitting methods (including the Coats-Redfern, the iterative procedure and masterplots method) were used to establish the kinetic model. Since the kinetic models established by the above three model-fitting methods were not completely consistent based on different approximations, considering the effect of different approximates on the model, the reaction mechanism was further established by comparing the conversion rate based on the model-fitting methods corresponding to the possible reaction mechanisms. Finally, the accuracy of the above model-fitting methods and Particle Swarm Optimization (PSO) algorithm were compared. Results showed that the reaction function g(α) = (1 − α)−1 − 1 might be the most suitable to characterize the pyrolysis of XPS. The conversion rate calculated by masterplots and PSO methods could provide the best agreement with the experimental data.

scholarly journals Energy Utilization of Building Insulation Waste Expanded Polystyrene: Pyrolysis Kinetic Estimation by a New Comprehensive Method

Polymers ◽  
2020 ◽  
Vol 12 (8) ◽  
pp. 1744 ◽  
Author(s):  
Xiaoyang Ni ◽  
Zheng Wu ◽  
Wenlong Zhang ◽  
Kaihua Lu ◽  
Yanming Ding ◽  
...  
Keyword(s):  
Kinetic Parameters ◽  
Thermal Insulation ◽  
Large Scale ◽  
Model Fitting ◽  
Pso Algorithm ◽  
Expanded Polystyrene ◽  
Energy Utilization ◽  
Pyrolysis Kinetics ◽  
Model Free ◽  
Pyrolysis Kinetic

Expanded polystyrene (EPS) has excellent thermal insulation properties and is widely applied in building energy conservation. However, these thermal insulation materials have caused numerous fires because of flammability. Pyrolysis is necessary to support combustion, and more attention should be paid to the pyrolysis characteristics of EPS. Moreover, pyrolysis is considered to be an effective method for recycling solid waste. Pyrolysis kinetics of EPS were analyzed by thermogravimetric experiments, both in nitrogen and air atmospheres. A new method was proposed to couple the Flynn–Wall–Ozawa model-free method and the model-fitting method called the Coats–Redfern as well as the particle swarm optimization (PSO) global algorithm to establish reaction mechanisms and their corresponding kinetic parameters. It was found that the pyrolysis temperature of EPS was concentrated at 525–800 K. The activation energy of EPS in nitrogen was about 163 kJ/mol, which was higher than that in air (109.63 kJ/mol). Furthermore, coupled with Coats–Redfern method, reaction functions g(α) = 1 − (1 − α)3 and g(α) = 1 − (1 − α)1/4 should be responsible for nitrogen and air reactions, respectively. The PSO algorithm was applied to compute detailed pyrolysis kinetic parameters. Kinetic parameters could be used in further large-scale fire simulation and provide guidance for reactor design.

scholarly journals Kinetic studies on the pyrolysis of plastic waste using a combination of model-fitting and model-free methods

2020 ◽  
Vol 38 (1_suppl) ◽  
pp. 77-85 ◽  
Author(s):  
Zhitong Yao ◽  
Shaoqi Yu ◽  
Weiping Su ◽  
Weihong Wu ◽  
Junhong Tang ◽  
...  
Keyword(s):  
Reaction Mechanism ◽  
Thermogravimetric Analysis ◽  
Compensation Effect ◽  
Model Fitting ◽  
Plastic Waste ◽  
Plastic Shell ◽  
Ozawa Method ◽  
Heating Rates ◽  
Helium Atmosphere ◽  
Model Free

In this work, the pyrolysis behavior of plastic waste—TV plastic shell—was investigated, based on thermogravimetric analysis and using a combination of model-fitting and model-free methods. The possible reaction mechanism and kinetic compensation effects were also examined. Thermogravimetric analysis indicated that the decomposition of plastic waste in a helium atmosphere can be divided into three stages: the minor loss stage (20–300°C), the major loss stage (300–500°C) and the stable loss stage (500–1000°C). The corresponding weight loss at three different heating rates of 15, 25 and 35 K/min were determined to be 2.80–3.02%, 94.45–95.11% and 0.04–0.16%, respectively. The activation energy ( Ea) and correlation coefficient ( R2) profiles revealed that the kinetic parameters calculated using the Friedman and Kissinger–Akahira–Sunose method displayed a similar trend. The values from the Flynn–Wall–Ozawa and Starink methods were comparable, although the former gave higher R2 values. The Eα values gradually decreased from 269.75 kJ/mol to 184.18 kJ/mol as the degree of conversion ( α) increased from 0.1 to 0.8. Beyond this range, the Eα slightly increased to 211.31 kJ/mol. The model-fitting method of Coats–Redfern was used to predict the possible reaction mechanism, for which the first-order model resulted in higher R2 values than and comparable Eα values to those obtained from the Flynn–Wall–Ozawa method. The pre-exponential factors (ln A) were calculated based on the F1 reaction model and the Flynn–Wall–Ozawa method, and fell in the range 59.34–48.05. The study of the kinetic compensation effect confirmed that a compensation effect existed between Ea and ln A during the plastic waste pyrolysis.

Thermo-catalytic decomposition of polystyrene waste: Comparative analysis using different kinetic models

2019 ◽  
Vol 38 (2) ◽  
pp. 202-212 ◽  
Author(s):  
Ghulam Ali ◽  
Jan Nisar ◽  
Munawar Iqbal ◽  
Afzal Shah ◽  
Mazhar Abbas ◽  
...  
Keyword(s):  
Activation Energy ◽  
Copper Oxide ◽  
Solid Waste ◽  
Thermodynamic Parameters ◽  
Model Fitting ◽  
Catalytic Decomposition ◽  
Decomposition Reaction ◽  
Inert Atmosphere ◽  
Heating Rates ◽  
Model Free

Due to a huge increase in polymer production, a tremendous increase in municipal solid waste is observed. Every year the existing landfills for disposal of waste polymers decrease and the effective recycling techniques for waste polymers are getting more and more important. In this work pyrolysis of waste polystyrene was performed in the presence of a laboratory synthesized copper oxide. The samples were pyrolyzed at different heating rates that is, 5°Cmin−1, 10°Cmin−1, 15°Cmin−1 and 20°Cmin−1 in a thermogravimetric analyzer in inert atmosphere using nitrogen. Thermogravimetric data were interpreted using various model fitting (Coats–Redfern) and model free methods (Ozawa–Flynn–Wall, Kissinger–Akahira–Sunose and Friedman). Thermodynamic parameters for the reaction were also determined. The activation energy calculated applying Coats–Redfern, Ozawa–Flynn–Wall, Kissinger–Akahira–Sunose and Friedman models were found in the ranges 105–148.48 kJmol−1, 99.41–140.52 kJmol−1, 103.67–149.15 kJmol−1 and 99.93–141.25 kJmol−1, respectively. The lowest activation energy for polystyrene degradation in the presence of copper oxide indicates the suitability of catalyst for the decomposition reaction to take place at lower temperature. Moreover, the obtained kinetics and thermodynamic parameters would be very helpful in determining the reaction mechanism of the solid waste in a real system.

scholarly journals Thermal decomposition of potassium titanium oxalate

2011 ◽  
Vol 76 (7) ◽  
pp. 1015-1026 ◽  
Author(s):  
Karuvanthodi Muraleedharan ◽  
Labeeb Pasha
Keyword(s):  
Carbon Dioxide ◽  
Thermal Decomposition ◽  
Carbon Monoxide ◽  
Model Fitting ◽  
Nitrogen Atmosphere ◽  
Single Step ◽  
Heating Rates ◽  
Decomposition Stage ◽  
Model Free ◽  
Good Agreement

The thermal decomposition of potassium titanium oxalate (PTO) was studied using non-isothermal thermogravimetry at different heating rates under a nitrogen atmosphere. The thermal decomposition of PTO proceeds mainly through five stages forming potassium titanate. The theoretical and experimental mass loss data are in good agreement for all stages of the thermal decomposition of PTO. The third thermal decomposition stage of PTO, the combined elimination of carbon monoxide and carbon dioxide, were subjected to kinetic analyses both by the method of model fitting and by the model free approach, which is based on the isoconversional principle. The model free analyses showed that the combined elimination of carbon monoxide and carbon dioxide and formation of final titanate in the thermal decomposition of PTO proceeds through a single step with an activation energy value of about 315 kJ mol-1.

Kinetic Studies on the Thermal Synthesis of Fluorapatite: Model Free and Model-Fitting Methods

2018 ◽  
Vol 28 ◽  
pp. 75-89
Author(s):  
Hamid Reza Javadinejad ◽  
Sayed Ahmad Hosseini ◽  
Mohsen Saboktakin Rizi ◽  
Eiman Aghababaei ◽  
Hossein Naseri
Keyword(s):  
Activation Energy ◽  
Model Fitting ◽  
Kinetic Studies ◽  
Isoconversional Methods ◽  
Reaction Model ◽  
Heating Rates ◽  
Thermal Synthesis ◽  
Exponential Factor ◽  
Model Free ◽  
Master Plots

The kinetic study for the synthesis of Fluorapatite has been done using the thermogravimetric technique under non-isothermal conditions and at four heating rates of 5, 10, 15 and 20 °C. Both model free and model-fitting methods were used to investigate kinetic parameters. Calcium oxide, phosphorus pentoxide and calcium fluoride were used as the precursor materials. The activation energy values were calculated through model-fitting and isoconversional methods and were used to predict the reaction model and pre-exponential factor. In this case several techniques were considered such as master plots and compensation effects. The results indicated that the reaction mechanism was chemically controlled with second and third order reaction models in the whole range of conversion which the activation energy varied from 25 to 43 kJ/mol.

scholarly journals Determination of Kinetic Parameters for the Thermal Decomposition of Parthenium hysterophorus

2018 ◽  
Vol 22 (1) ◽  
pp. 5-21 ◽  
Author(s):  
Alok Dhaundiyal ◽  
Suraj B. Singh ◽  
Muammel M. Hanon ◽  
Rekha Rawat
Keyword(s):  
Thermal Decomposition ◽  
Kinetic Parameters ◽  
Model Fitting ◽  
Frequency Factor ◽  
Heating Rates ◽  
Model Free ◽  
Higher Temperature ◽  
Good Agreement ◽  
Maximum Weight Loss

Abstract A kinetic study of pyrolysis process of Parthenium hysterophorous is carried out by using thermogravimetric analysis (TGA) equipment. The present study investigates the thermal degradation and determination of the kinetic parameters such as activation E and the frequency factor A using model-free methods given by Flynn Wall and Ozawa (FWO), Kissinger-Akahira-Sonuse (KAS) and Kissinger, and model-fitting (Coats Redfern). The results derived from thermal decomposition process demarcate decomposition of Parthenium hysterophorous among the three main stages, such as dehydration, active and passive pyrolysis. It is shown through DTG thermograms that the increase in the heating rate caused temperature peaks at maximum weight loss rate to shift towards higher temperature regime. The results are compared with Coats Redfern (Integral method) and experimental results have shown that values of kinetic parameters obtained from model-free methods are in good agreement. Whereas the results obtained through Coats Redfern model at different heating rates are not promising, however, the diffusion models provided the good fitting with the experimental data.

scholarly journals Application of a New Statistical Model for the Description of Solid Fuel Decomposition in the Analysis of Artemisia apiacea Pyrolysis

Energies ◽  
2021 ◽  
Vol 14 (18) ◽  
pp. 5789
Author(s):  
Tianbao Gu ◽  
Torsten Berning ◽  
Chungen Yin
Keyword(s):  
Experimental Data ◽  
Reaction Mechanism ◽  
Statistical Model ◽  
Solid Fuel ◽  
Conversion Rate ◽  
Reaction Model ◽  
Thermochemical Conversion ◽  
Conversion Degree ◽  
Heating Rates ◽  
Artemisia Apiacea

Pyrolysis, one of the key thermochemical conversion technologies, is very promising to obtain char, oil and combustible gases from solid fuels. Kinetic modeling is a crucial method for the prediction of the solid conversion rate and analysis of the pyrolysis process. We recently developed a new statistical model for the universal description of solid fuel decomposition, which shows great potential in studying solid fuel pyrolysis. This paper demonstrates three essential applications of this new model in the analysis of Artemisia apiacea pyrolysis, i.e., identification of the conversion rate peak position, determination of the reaction mechanism, and evaluation of the kinetics. The results of the first application show a very good agreement with the experimental data. From the second application, the 3D diffusion-Jander reaction model is considered as the most suitable reaction mechanism for the description of Artemisia stem pyrolysis. The third application evaluates the kinetics of Artemisia stem pyrolysis. The evaluated kinetics vary with the conversion degree and heating rates, in which the activation energies and pre-exponential factors (i.e., lnA vs. Ea) show a linear relationship, regardless of the conversion and heating rates. Moreover, the prediction of the conversion rate using the obtained kinetics shows an excellent fit with the experimental data.

scholarly journals Kinetic Analysis of Pyrolysis and Thermo-Oxidative Decomposition of Tennis String Nylon Wastes

Materials ◽  
2021 ◽  
Vol 14 (24) ◽  
pp. 7564
Author(s):  
Haibo Wan ◽  
Zhen Huang
Keyword(s):  
Thermal Degradation ◽  
Kinetic Analysis ◽  
Model Fitting ◽  
Degradation Process ◽  
Nylon 6 ◽  
Reaction Model ◽  
Heating Rates ◽  
Model Free ◽  
Order Chemical Reaction ◽  
First Order Chemical Reaction

Thermal degradation of nylon-6 tennis string nylon wastes in inert nitrogen and air atmospheres was investigated by means of multiple heating-rate thermogravimetric analyses. The results obtained under the heating rates of 5–20 K/min are compared in terms of degradation feature and specific temperature for two atmospheres. Using nonisothermal data, kinetic analysis was thoroughly conducted using various isoconversional model-free methods, including Starink, Madhusudanan–Krishnan–Ninan, Tang, Coats–Redfern, and Flynn–Wall–Ozawa methods. With these kinetic analysis methods, the activation energy over the entire degradation process was successfully calculated. By means of the model-fitting master-plots method, the first-order chemical reaction model was determined to be the most appropriate mechanism function for describing pyrolysis and oxidative thermal degradation of nylon-6 waste. Using kinetic parameters, satisfactory matching against experimental data resulted using the Coats–Redfern method for both cases. Furthermore, thermodynamic parameters such as changes in entropy, enthalpy, and Gibbs free energy during thermal degradation processes were evaluated.

Thermal degradation kinetics and lifetime of HDPE/PLLA/pro-oxidant blends

2016 ◽  
Vol 36 (9) ◽  
pp. 917-931 ◽  
Author(s):  
Gaurav Madhu ◽  
Dev K. Mandal ◽  
Haripada Bhunia ◽  
Pramod K. Bajpai
Keyword(s):  
Activation Energy ◽  
Thermal Degradation ◽  
Degradation Kinetics ◽  
Model Fitting ◽  
Frequency Factor ◽  
Thermal Degradation Kinetics ◽  
Heating Rates ◽  
Model Free ◽  
Calculation Technique ◽  
Thermal Degradation Behavior

Abstract The effect of adding poly(L-lactic acid) (PLLA) with and without a pro-oxidant additive cobalt stearate (CoSt) and compatibilizer maleic anhydride grafted polyethylene (MA-g-PE) on the thermal degradation and stability of high-density polyethylene (HDPE) films was analyzed using thermogravimetric analysis (TGA). The kinetic parameters [i.e. activation energy (Ea), order of reaction (n), and frequency factor ln(A)] of the samples were studied over a temperature range of 25°C–600°C at four heating rates (i.e. 5, 10, 15, and 20°C/min) through model-free techniques (e.g. Friedman, second Kissinger, and Flynn-Wall-Ozawa) and model-fitting techniques (e.g. Freeman-Carroll and Kim-Park). The value of Ea for neat HDPE was found to be much higher than PLLA; for the HDPE/PLLA blend, it was nearer to that of HDPE. An increase in the activation energy of 80/20 (HDPE/PLLA) blend was noticed by the addition of MA-g-PE. The TGA data and degradation kinetics were also used to predict the lifetime of the film samples. The lifetime of HDPE was found to decrease with the increase in the concentration of CoSt, thereby revealing its pro-oxidative ability. Minimum lifetime was noted for the HDPE/PLLA (80/20) sample blended with CoSt, which increased slightly in the presence of MA-g-PE. Studies indicated that the thermal degradation behavior and lifetime of the investigated film samples depends not only on the fractions of their constituents but also on the heating rates and calculation technique.

scholarly journals Kinetic Analysis of Low-Rank Coal Pyrolysis by Model-Free and Model-Fitting Methods

2019 ◽  
Vol 2019 ◽  
pp. 1-7 ◽  
Author(s):  
Qiuli Zhang ◽  
Min Luo ◽  
Long Yan ◽  
Aiwu Yang ◽  
Xiangrong Hui
Keyword(s):  
Model Fitting ◽  
Decomposition Reaction ◽  
Low Rank ◽  
Coal Pyrolysis ◽  
Pyrolysis Kinetics ◽  
Heating Rates ◽  
Pyrolysis Characteristics ◽  
Model Free ◽  
Thermal Analyzer ◽  
Thermogravimetric Data

Coal SJC, coal WJG, coal ZJM, and coal HCG were selected to investigate the pyrolysis kinetics of northern Shaanxi coals. TG and DSC experiments of four coals were carried out with a synchronous thermal analyzer at heating rates 5, 10, 15, and 20 C/min, respectively. The pyrolysis characteristics were described by thermogravimetric data, and the kinetic parameters were calculated by Flynn–Wall–Ozawa (FWO), Kissinger, general integration, and MacCallum–Tanner methods. The results show that coal SJC, coal ZJM, and coal HCG all conform to the reaction series equation, the thermal decomposition reaction rate is controlled by chemical reaction, and coal WJG conforms to Avrami–Erofeev equation. The activation energies of the four coals are 177.53 kJ/mol, 200.34 kJ/mol, 158.59 kJ/mol, and 240.47 kJ/mol, respectively.

Sign in / Sign up

Export Citation Format

Share Document