scholarly journals Structure and Photoluminescence Properties of Thermally Synthesized V2O5 and Al-Doped V2O5 Nanostructures

Materials ◽  
2021 ◽  
Vol 14 (2) ◽  
pp. 359
Author(s):  
Chih-Chiang Wang ◽  
Chia-Lun Lu ◽  
Fuh-Sheng Shieu ◽  
Han C. Shih
Keyword(s):  
Photoelectron Spectroscopy ◽  
Chemical Vapor ◽  
Growth Direction ◽  
Photoluminescence Intensity ◽  
X Ray Diffraction ◽  
Smart Windows ◽  
X Ray ◽  
Transmission Electron ◽  
Potential Applications ◽  
Li Ion

Al-free and Al-doped V2O5 nanostructures were synthesized by a thermal-chemical vapor deposition (CVD) process on Si(100) at 850 °C under 1.2 × 10−1 Torr via a vapor-solid (V-S) mechanism. X-ray diffraction (XRD), Raman, and high-resolution transmission electron microscopy (HRTEM) confirmed a typical orthorhombic V2O5 with the growth direction along [110]-direction of both nanostructures. Metallic Al, rather than Al3+-ion, was detected by X-ray photoelectron spectroscopy (XPS), affected the V2O5 crystallinity. The photoluminescence intensity of V2O5 nanostructure at 1.77 and 1.94 eV decreased with the increasing Al-dopant by about 61.6% and 59.9%, attributing to the metallic Al intercalated between the V2O5-layers and/or filled in the oxygen vacancies, which behaved as electron sinks. Thus the Al-doped V2O5 nanostructure shows the potential applications in smart windows and the electrodic material in a Li-ion battery.

scholarly journals Synthesis of Three-Dimensional Fe3O4/Graphene Aerogels for the Removal of Arsenic Ions from Water

2015 ◽  
Vol 2015 ◽  
pp. 1-6 ◽  
Author(s):  
Yan Ye ◽  
Da Yin ◽  
Bin Wang ◽  
Qingwen Zhang
Keyword(s):  
Electron Microscopy ◽  
Photoelectron Spectroscopy ◽  
3D Structure ◽  
Three Dimensional ◽  
X Ray Diffraction ◽  
X Ray ◽  
Graphene Aerogels ◽  
Transmission Electron ◽  
Potential Applications ◽  
Removal Of Arsenic

We report the synthesis of three-dimensional Fe3O4/graphene aerogels (GAs) and their application for the removal of arsenic (As) ions from water. The morphology and properties of Fe3O4/GAs have been characterized by scanning electron microscopy, transmission electron microscopy, X-ray diffraction, X-ray photoelectron spectroscopy, and superconducting quantum inference device. The 3D nanostructure shows that iron oxide nanoparticles are decorated on graphene with an interconnected network structure. It is found that Fe3O4/GAs own a capacity of As(V) ions adsorption up to 40.048 mg/g due to their remarkable 3D structure and existence of magnetic Fe3O4nanoparticles for separation. The adsorption isotherm matches well with the Langmuir model and kinetic analysis suggests that the adsorption process is pseudo-second-ordered. In addition to the excellent adsorption capability, Fe3O4/GAs can be easily and effectively separated from water, indicating potential applications in water treatment.

scholarly journals Luminescence Studies and Judd–Ofelt Analysis on SiO2@LaPO4:Eu@SiO2 Submicro-spheres with Different Size of Intermediate Shells

2019 ◽  
Vol 9 (1) ◽  
Author(s):  
Xiaowei Zhu ◽  
Kuisuo Yang ◽  
Anping Wu ◽  
He Bai ◽  
Jinrong Bao ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Photoelectron Spectroscopy ◽  
Optical Transition ◽  
Dipole Transition ◽  
Rare Earth Ions ◽  
Photoluminescence Intensity ◽  
The Novel ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron

Abstract The novel submicro-spheres SiO2@LaPO4:Eu@SiO2 with core-shell-shell structures were prepared by connecting the SiO2 submicro-spheres and the rare earth ions through an organosilane HOOCC6H4N(CONH(CH2)3Si(OCH2CH3)3 (MABA-Si). The as-prepared products were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS), and infrared spectroscopy (IR). It is found that the intermediate shell of the submicro-spheres was composed by LaPO4:Eu nanoparticles with the size of about 4, 5–7, or 15–34 nm. A possible formation mechanism for the SiO2@LaPO4:Eu@SiO2 submicro-spheres has been proposed. The dependence of the photoluminescence intensity on the size of the LaPO4:Eu nanoparticles has been investigated. The intensity ratios of electrical dipole transition 5D0 → 7F2 to magnetic dipole transition 5D0 → 7F1 of Eu3+ ions were increased with decreasing the size of LaPO4:Eu nanoparticles. According to the Judd-Ofelt (J-O) theory, when the size of LaPO4:Eu nanoparticles was about 4, 5–7 and 15–34 nm, the calculated J-O parameter Ω2 (optical transition intensity parameter) was 2.30 × 10−20, 1.80 × 10−20 and 1.20 × 10−20, respectively. The increase of Ω2 indicates that the symmetry of Eu3+ in the LaPO4 lattice was gradually reduced. The photoluminescence intensity of the SiO2@LaPO4:Eu@SiO2 submicro-spheres was unquenched in aqueous solution even after 15 days.

scholarly journals Deposition Mechanism and Thickness Control of CVD SiC Coatings on NextelTM440 Fibers

Coatings ◽  
2020 ◽  
Vol 10 (4) ◽  
pp. 408
Author(s):  
Yi Wang ◽  
Jian Sun ◽  
Bing Sheng ◽  
Haifeng Cheng
Keyword(s):  
Coating Thickness ◽  
Photoelectron Spectroscopy ◽  
Deposition Time ◽  
Chemical Vapor ◽  
X Ray Diffraction ◽  
Deposition Mechanism ◽  
Thickness Control ◽  
X Ray ◽  
Transmission Electron ◽  
Sic Coatings

SiC coatings were successfully synthesized on NextelTM440 fibers by chemical vapor deposition (CVD) using methyltrichlorosilane as the original SiC source at 1373 K. After deposited, the fibers were fully surrounded by uniform coatings with some bulges. The X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS) and high-resolution transmission electron microscopy (HR-TEM) results indicated that the coatings were composed of β-SiC and free carbon. Moreover, thickness control of the coatings could be carried out by adjusting the deposition time. The coating thickness rose exponentially, and the exterior of the coatings became looser as the deposition time increased. The thickness of about 1.5 µm was obtained after depositing for 4 h. The coating thickness was also theoretically calculated, and the result agreed well with the measured thickness. Finally, the related deposition mechanism is discussed and a deposition model is built.

SYNTHESIS, CHARACTERIZATION AND THE APPLICABILITY OF β-CYCLODEXTRINS FUNCTIONALIZED MESOPOROUS SBA-15 MOLECULAR SIEVES

NANO ◽  
2013 ◽  
Vol 08 (05) ◽  
pp. 1350050
Author(s):  
MIN GUAN ◽  
HAI-PENG BI ◽  
ZUYUAN WANG ◽  
SHAOHUA BU ◽  
LING HUANG ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Photoelectron Spectroscopy ◽  
Molecular Sieves ◽  
Nitrogen Adsorption ◽  
X Ray Diffraction ◽  
X Ray ◽  
Adsorption Capacities ◽  
Transmission Electron ◽  
Potential Applications ◽  
Adsorption Desorption

Mesoporous silicas SBA-15 are modified with β-Cyclodextrins (β-CD) by simple grafting method. β-CD functionalized SBA-15 was characterized by Fourier transform infrared (FTIR) spectroscopy, transmission electron microscopy (TEM), scanning electron microscopy (SEM), powder X-ray diffraction (PXRD), nitrogen adsorption–desorption measurements, thermogravimetric analysis (TGA) and X-ray photoelectron spectroscopy (XPS). Furthermore, the applicability of it is investigated through studying the adsorption properties of clenbuterol. It showed better adsorption capacities of clenbuterol than pure SBA-15. β-CD functionalized SBA-15 material has the potential applications in the treatment of clenbuterol contamination in food and environment science.

Synthesis of MoO3/V2O5/C Composite as Novel Anode for Li-Ion Battery Application

2020 ◽  
Vol 20 (5) ◽  
pp. 2911-2916
Author(s):  
Zhen Zhang ◽  
Xiao Chen ◽  
Guangxue Zhang ◽  
Chuanqi Feng
Keyword(s):  
Electron Microscopy ◽  
Photoelectron Spectroscopy ◽  
Specific Capacity ◽  
Lithium Ion ◽  
Li Ion Battery ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Li Ion ◽  
Battery Application

The MoO3/V2O5/C, MoO3/C and V2O5/C are synthesized by electrospinning combined with heat treatment. These samples are characterized by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM), transmission electron microscopy (TEM), Raman spectroscopy and thermogravimetric analysis (TG) techniques. The results show that sample MoO3/V2O5/C is a composite composed from MoO3, V2O5 and carbon. It takes on morphology of the nanofibers with the diameter of 200~500 nm. The TG analysis result showed that the carbon content in the composite is about 40.63%. Electrochemical properties for these samples are studied. When current density is 0.2 A g−1, the MoO3/V2O5/C could retain the specific capacity of 737.6 mAh g−1 after 200 cycles and its coulomb efficiency is 92.99%, which proves that MoO3/V2O5/C has better electrochemical performance than that of MoO3/C and V2O5/C. The EIS and linear Warburg coefficient analysis results show that the MoO3/V2O5/C has larger Li+ diffusion coefficient and superior conductivity than those of MoO3/C or V2O5/C. So MoO3/V2O5/C is a promising anode material for lithium ion battery application.

Growth and characterization of type II ZnO/ZnSe core/shell nanowire arrays

2010 ◽  
Vol 25 (7) ◽  
pp. 1272-1277 ◽  
Author(s):  
Jinjian Zheng ◽  
Zhiming Wu ◽  
Weihuang Yang ◽  
Shuping Li ◽  
Junyong Kang
Keyword(s):  
Electron Microscopy ◽  
Chemical Vapor ◽  
Band Alignment ◽  
Nanowire Arrays ◽  
Core Shell ◽  
Type Ii ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Potential Applications

Type II ZnO/ZnSe core/shell nanowire arrays were grown by a two-step chemical vapor deposition. The nanowire arrays with dense nanoislands on the surface are well aligned and normal to the substrate imaged by scanning electron microscopy. The core/shell structure of nanowires was identified by a high-resolution transmission electron microscopy. The structure and composition of the shell were confirmed to be wurtzite ZnSe by x-ray diffraction, Raman scattering and energy-dispersive x-ray spectroscopy. Moreover, an intense emission was observed at 1.89 eV smaller than the band gaps of core and shell materials by photoluminescence, indicating the achievement of the type II band alignment at the interface. This study is expected to contribute to the potential applications in novel photovoltaic devices.

scholarly journals Grain Structure and Growth of Dispersed Phase BN-AlN Coatings Grown via Chemical Vapor Deposition

1990 ◽  
Vol 202 ◽  
Author(s):  
Garth B. Freeman ◽  
Woo Y. Lee ◽  
W. J. Lackey ◽  
John A. Hanigofsky ◽  
Karren More
Keyword(s):  
Electron Microscopy ◽  
Photoelectron Spectroscopy ◽  
Substrate Surface ◽  
Chemical Vapor ◽  
Ceramic Coatings ◽  
Grain Structure ◽  
Dispersed Phase ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron

ABSTRACTThis paper discusses the variation in microstructures encountered during the separate depositions of boron nitride (BN) and aluminum nitride (A1N) as well as during the codeposition of BNߝA1N dispersed phase ceramic coatings. This combination was chosen in order to take advantage of the self lubricating properties of hexagonal BN along with the hard, erosion resistance of A1N. Films were characterized using scanning and transmission electron microscopy (SEM and TEM), x-ray photoelectron spectroscopy (XPS), and x-ray diffraction (XRD).A range of coating microstructures are possible depending on the conditions of deposition. The best films produced, in terms of hardness, density, and tenacity, were a fine mixture of turbostratic BN and preferentially oriented A1N whiskers aligned with the whisker axis perpendicular to the substrate surface as seen by both electron microscopy and x-ray diffraction.

Protocrystalline Silicon at High Rate from Undiluted Silane

2004 ◽  
Vol 808 ◽  
Author(s):  
R.E.I. Schropp ◽  
M.K. van Veen ◽  
C.H.M. van der Werf ◽  
D.L. Williamson ◽  
A.H. Mahan
Keyword(s):  
Stainless Steel ◽  
Plasma Deposition ◽  
Silicon Layer ◽  
Chemical Vapor ◽  
Growth Direction ◽  
High Rate ◽  
Fast Method ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron

ABSTRACTHot Wire Chemical Vapor Deposition (HWCVD) is shown to be a fast method for the deposition of protocrystalline silicon films from undiluted silane. Intrinsic silicon-hydrogen films (2 μm thick) have been deposited by HWCVD on plain stainless steel as well as on stainless steel precoated with a n-type doped microcrystalline silicon layer. In X-ray diffraction experiments, the linewidths of the first sharp peak (FSP) were 5.59 ± 0.09 degrees and 5.29 ± 0.11 degrees, respectively, indicating improved medium-range order and a template effect due to the μc-Si:H n-layer. For thinner layers (0.7 μm thick), the linewidths of the FSP were 5.29 ± 0.09 degrees and 5.10 ± 0.09 degrees. These FSPs are as narrow as for optimized i-layers made by H2-diluted plasma deposition, however, at a much higher deposition rate (1 nm/s), at moderate temperature (250°C), and without the use of H2 dilution. In accompanying transmission electron micro-graphs, the layers show a significant concentration of elongated small voids in the growth direction that are not interconnected. Small Angle X-ray Scattering (SAXS) results are consistent with these observations. We suspect that the void nature allows the bulk of the film to be more ordered. The utilization of such layers in n-i- p solar cells on plain stainless steel leads to cells with a remarkably good stability, showing a decrease of the fill factor of less than 10 % during 1500 h of light soaking.

scholarly journals α-Cellulose Fibers of Paper-Waste Origin Surface-Modified with Fe3O4 and Thiolated-Chitosan for Efficacious Immobilization of Laccase

Polymers ◽  
2021 ◽  
Vol 13 (4) ◽  
pp. 581
Author(s):  
Gajanan S. Ghodake ◽  
Surendra K. Shinde ◽  
Ganesh D. Saratale ◽  
Rijuta G. Saratale ◽  
Min Kim ◽  
...  
Keyword(s):  
Enzyme Immobilization ◽  
Photoelectron Spectroscopy ◽  
Cellulose Fibers ◽  
Relative Activity ◽  
Significant Activity ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Laccase Immobilization ◽  
Surface Modified

The utilization of waste-paper-biomass for extraction of important α-cellulose biopolymer, and modification of extracted α-cellulose for application in enzyme immobilization can be extremely vital for green circular bio-economy. Thus, in this study, α-cellulose fibers were super-magnetized (Fe3O4), grafted with chitosan (CTNs), and thiol (-SH) modified for laccase immobilization. The developed material was characterized by high-resolution transmission electron microscopy (HR-TEM), HR-TEM energy dispersive X-ray spectroscopy (HR-TEM-EDS), X-ray diffraction (XRD), vibrating sample magnetometer (VSM), X-ray photoelectron spectroscopy (XPS), and Fourier transform infrared spectroscopy (FT-IR) analyses. Laccase immobilized on α-Cellulose-Fe3O4-CTNs (α-Cellulose-Fe3O4-CTNs-Laccase) gave significant activity recovery (99.16%) and laccase loading potential (169.36 mg/g). The α-Cellulose-Fe3O4-CTNs-Laccase displayed excellent stabilities for temperature, pH, and storage time. The α-Cellulose-Fe3O4-CTNs-Laccase applied in repeated cycles shown remarkable consistency of activity retention for 10 cycles. After the 10th cycle, α-Cellulose-Fe3O4-CTNs possessed 80.65% relative activity. Furthermore, α-Cellulose-Fe3O4-CTNs-Laccase shown excellent degradation of pharmaceutical contaminant sulfamethoxazole (SMX). The SMX degradation by α-Cellulose-Fe3O4-CTNs-Laccase was found optimum at incubation time (20 h), pH (3), temperatures (30 °C), and shaking conditions (200 rpm). Finally, α-Cellulose-Fe3O4-CTNs-Laccase gave repeated degradation of SMX. Thus, this study presents a novel, waste-derived, highly capable, and super-magnetic nanocomposite for enzyme immobilization applications.

scholarly journals Surface Stoichiometry and Depth Profile of Tix-CuyNz Thin Films Deposited by Magnetron Sputtering

Materials ◽  
2021 ◽  
Vol 14 (12) ◽  
pp. 3191
Author(s):  
Arun Kumar Mukhopadhyay ◽  
Avishek Roy ◽  
Gourab Bhattacharjee ◽  
Sadhan Chandra Das ◽  
Abhijit Majumdar ◽  
...  
Keyword(s):  
Magnetron Sputtering ◽  
Photoelectron Spectroscopy ◽  
Film Surface ◽  
Grazing Incidence ◽  
X Ray Diffraction ◽  
X Ray ◽  
Relative Composition ◽  
Transmission Electron ◽  
Deposited Film ◽  
Deposited Films

We report the surface stoichiometry of Tix-CuyNz thin film as a function of film depth. Films are deposited by high power impulse (HiPIMS) and DC magnetron sputtering (DCMS). The composition of Ti, Cu, and N in the deposited film is investigated by X-ray photoelectron spectroscopy (XPS). At a larger depth, the relative composition of Cu and Ti in the film is increased compared to the surface. The amount of adventitious carbon which is present on the film surface strongly decreases with film depth. Deposited films also contain a significant amount of oxygen whose origin is not fully clear. Grazing incidence X-ray diffraction (GIXD) shows a Cu3N phase on the surface, while transmission electron microscopy (TEM) indicates a polycrystalline structure and the presence of a Ti3CuN phase.

Sign in / Sign up

Export Citation Format

Share Document