scholarly journals Structural and Photoluminescence Investigations of Tb3+/Eu3+ Co-Doped Silicate Sol-Gel Glass-Ceramics Containing CaF2 Nanocrystals

Materials ◽  
2021 ◽  
Vol 14 (4) ◽  
pp. 754
Author(s):  
Natalia Pawlik ◽  
Barbara Szpikowska-Sroka ◽  
Tomasz Goryczka ◽  
Joanna Pisarska ◽  
Wojciech A. Pisarski
Keyword(s):  
Sol Gel ◽  
Glass Ceramics ◽  
Emission Spectra ◽  
Molar Ratio ◽  
X Ray Diffraction ◽  
Co Doping ◽  
Near Ultraviolet ◽  
Transmission Electron ◽  
Co Doped

In this work, the series of Tb3+/Eu3+ co-doped xerogels and derivative glass-ceramics containing CaF2 nanocrystals were prepared and characterized. The in situ formation of fluoride crystals was verified by an X-ray diffraction technique (XRD) and transmission electron microscopy (TEM). The studies of the Tb3+/Eu3+ energy transfer (ET) process were performed based on excitation and emission spectra along with luminescence decay analysis. According to emission spectra recorded under near-ultraviolet (NUV) excitation (351 nm, 7F6 → 5L9 transition of Tb3+), the mutual coexistence of the 5D4 → 7FJ (J = 6–3) (Tb3+) and the 5D0 → 7FJ (J = 0–4) (Eu3+) luminescence bands was clearly observed. The co-doping also resulted in gradual shortening of a lifetime from the 5D4 state of Tb3+ ions, and the ET efficiencies were varied from ηET = 11.9% (Tb3+:Eu3+ = 1:0.5) to ηET = 22.9% (Tb3+:Eu3+ = 1:2) for xerogels, and from ηET = 25.7% (Tb3+:Eu3+ = 1:0.5) up to ηET = 67.4% (Tb3+:Eu3+ = 1:2) for glass-ceramics. Performed decay analysis from the 5D0 (Eu3+) and the 5D4 (Tb3+) state revealed a correlation with the change in Tb3+–Eu3+ and Eu3+–Eu3+ interionic distances resulting from both the variable Tb3+:Eu3+ molar ratio and their partial segregation in CaF2 nanophase.

Eu3+/Tb3+ Co-Doped Cerium Oxide Transparent Nanocomposite for Color-Tunable Emission

NANO ◽  
2018 ◽  
Vol 13 (10) ◽  
pp. 1850119
Author(s):  
Xiaoyan Li ◽  
Yunlong Yu ◽  
Xiangfeng Guan ◽  
Peihui Luo ◽  
Linqin Jiang ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Thermal Stability ◽  
Transmission Electron Microscopy ◽  
Sol Gel ◽  
Homogeneous Precipitation ◽  
Transmission Electron ◽  
Color Tunable ◽  
Co Doped ◽  
Tunable Emission

Eu[Formula: see text]/Tb[Formula: see text] co-doped nanocomposite containing CeO2 nanocrystals was successfully prepared by an in situ sol–gel polymerization approach. High-resolution transmission electron microscopy demonstrated the homogeneous precipitation of CeO2 nanocrystals among the polymethylmethacrylate (PMMA) matrix. The thermal stability and UV-shielding capability of the obtained nanocomposite were improved with increase of CeO2 content. The tuning of the emissive color from green and yellow to red can be easily achieved by varying the dopant species and concentration. These results suggested that the obtained nanocomposite could be potentially applicable in transparent solid-state luminescent devices.

scholarly journals Luminescence of SiO2-BaF2:Tb3+, Eu3+ Nano-Glass-Ceramics Made from Sol–Gel Method at Low Temperature

Nanomaterials ◽  
2022 ◽  
Vol 12 (2) ◽  
pp. 259
Author(s):  
Natalia Pawlik ◽  
Barbara Szpikowska-Sroka ◽  
Tomasz Goryczka ◽  
Ewa Pietrasik ◽  
Wojciech A. Pisarski
Keyword(s):  
Sol Gel ◽  
Three Dimensional ◽  
Glass Ceramics ◽  
Emission Spectra ◽  
Scanning Calorimetry ◽  
Light Emitting ◽  
Co Doping ◽  
Dsc Measurements ◽  
Decay Times

The synthesis and characterization of multicolor light-emitting nanomaterials based on rare earths (RE3+) are of great importance due to their possible use in optoelectronic devices, such as LEDs or displays. In the present work, oxyfluoride glass-ceramics containing BaF2 nanocrystals co-doped with Tb3+, Eu3+ ions were fabricated from amorphous xerogels at 350 °C. The analysis of the thermal behavior of fabricated xerogels was performed using TG/DSC measurements (thermogravimetry (TG), differential scanning calorimetry (DSC)). The crystallization of BaF2 phase at the nanoscale was confirmed by X-ray diffraction (XRD) measurements and transmission electron microscopy (TEM), and the changes in silicate sol–gel host were determined by attenuated total reflectance infrared (ATR-IR) spectroscopy. The luminescent characterization of prepared sol–gel materials was carried out by excitation and emission spectra along with decay analysis from the 5D4 level of Tb3+. As a result, the visible light according to the electronic transitions of Tb3+ (5D4 → 7FJ (J = 6–3)) and Eu3+ (5D0 → 7FJ (J = 0–4)) was recorded. It was also observed that co-doping with Eu3+ caused the shortening in decay times of the 5D4 state from 1.11 ms to 0.88 ms (for xerogels) and from 6.56 ms to 4.06 ms (for glass-ceramics). Thus, based on lifetime values, the Tb3+/Eu3+ energy transfer (ET) efficiencies were estimated to be almost 21% for xerogels and 38% for nano-glass-ceramics. Therefore, such materials could be successfully predisposed for laser technologies, spectral converters, and three-dimensional displays.

Effects of Glass Elements on the Structural Evolution ofin situGrown Ferroelectric Perovskite Crystals in Sol-gel Derived Glass-ceramics

1997 ◽  
Vol 12 (4) ◽  
pp. 1131-1140 ◽  
Author(s):  
Kui Yao ◽  
Weiguang Zhu ◽  
Liangying Zhang ◽  
Xi Yao
Keyword(s):  
Crystallization Process ◽  
Sol Gel ◽  
Glass Ceramics ◽  
Structural Evolution ◽  
Dielectric Measurements ◽  
X Ray Diffraction ◽  
Process Change ◽  
X Ray ◽  
Ferroelectric Perovskite

Several ABO3perovskite ferroelectric crystals, PbTiO3, Pb(Zr, Ti)O3, and BaTiO3have beenin situgrown from amorphous gels with glass elements, and the structural evolution has been systematically investigated using x-ray diffraction (XRD), infrared spectra (IR), differential thermal analysis (DTA), thermogravimetric analysis (TGA), and dielectric measurements. It is found that in the Si-contained glass-ceramic systems, Si and B glass elements are incorporated into the crystalline structures, resulting in the variation of the crystallization process, change of lattice constant, and dielectric properties. Some metastable phases expressed by a general formula AxByGzOw(A = Pb and Ba; B = Zr and Ti; G for glass elements, especially for Si) have been observed and discussed.

scholarly journals ZnFe2O4-TiO2Nanoparticles within Mesoporous MCM-41

2012 ◽  
Vol 2012 ◽  
pp. 1-8 ◽  
Author(s):  
Aidong Tang ◽  
Yuehua Deng ◽  
Jiao Jin ◽  
Huaming Yang
Keyword(s):  
Sol Gel ◽  
Rutile Phase ◽  
Band Gap Energy ◽  
Molar Ratio ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Agglomeration Of Nanoparticles ◽  
Adsorption Desorption ◽  
Mcm 41

A novel nanocomposite ZnFe2O4-TiO2/MCM-41 (ZTM) was synthesized by a sol-gel method and characterized through X-ray diffraction (XRD), high-resolution transmission electron microscopy (HRTEM), N2adsorption-desorption, Raman spectroscopy, and ultraviolet visible (UV-vis) spectrophotometry. The results confirmed the incorporation of ZnFe2O4-TiO2nanoparticles inside the pores of the mesoporous MCM-41 host without destroying its integrity. ZnFe2O4nanoparticles can inhibit the transformation of anatase into rutile phase of TiO2. Incorporation of ZnFe2O4-TiO2within MCM-41 avoided the agglomeration of nanoparticles and reduced the band gap energy of TiO2to enhance its visible light photocatalytic activity. UV-vis absorption edges of ZTM nanocomposites redshifted with the increase of Zn/Ti molar ratio. The nanocomposite approach could be a potential choice for enhancing the photoactivity of TiO2, indicating an interesting application in the photodegradation and photoelectric fields.

Iron and Iron-oxide on Silica Nanocomposites Prepared by the Sol-gel Method

2002 ◽  
Vol 17 (3) ◽  
pp. 590-596 ◽  
Author(s):  
G. Ennas ◽  
M. F. Casula ◽  
G. Piccaluga ◽  
S. Solinas ◽  
M. P. Morales ◽  
...  
Keyword(s):  
Sol Gel ◽  
Silica Matrix ◽  
Molar Ratio ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
Gel Method ◽  
Sol Gel Method ◽  
Silica Nanocomposites ◽  
Transmission Electron ◽  
Nanometric Particles

γ–Fe2O3/SiO2 and Fe/SiO2 nanocomposites, with a Fe/Si molar ratio of 0.25, were prepared by the sol-gel method starting from ethanolic solutions of tetraethoxysilane and iron (III) nitrate. After gelation the xerogels were oxidated or reduced. Samples were investigated by transmission electron microscopy, x-ray diffraction, differential scanning calorimetry, and thermogravimetry. Magnetic properties of the samples were investigated at room temperature (RT) and at 77 K. Nanometric particles supported in the silica matrix were obtained in all cases. Bigger particles (10 nm) were obtained in the case of Fe/SiO2 nanocomposites with respect to the γ–Fe2O3/SiO2 samples (5–8 nm). A slight effect of sol dilution on particle size was observed only in the case of γ–Fe2O3/SiO2 nanocomposites. A superparamagnetic behavior was shown at RT only by γ–Fe2O3/SiO2 nanocomposites. Iron-based composites exhibited coercivity values higher than 700 Oe at RT.

Structural and Electrical Properties of (Cu, Co) Co-Doped ZnO Thin Film

2013 ◽  
Vol 774-776 ◽  
pp. 964-967
Author(s):  
Ping Cao ◽  
Yue Bai
Keyword(s):  
Electrical Properties ◽  
Sol Gel ◽  
Hall Effect Measurement ◽  
X Ray Diffraction ◽  
Zno Film ◽  
Co Doping ◽  
Structural And Electrical Properties ◽  
Doped Zno ◽  
Cu Ions ◽  
Co Doped

Successful synthesis of Cu, Co co-doped ZnO film is obtained by sol-gel method. The structural and electrical properties of the sample were investigated. X-ray diffraction spectroscopy analyses indicate that the Co and Cu co-doping can not disturb the structure of ZnO. No additional peaks are observed in the Zn0.99Co0.01CuxO and Cu+ and Co2+ substitute for Zn2+ without changing the wurtzite structure. By Hall-effect measurement p-type conductivity was observed for the Cu co-doped film. XPS result confirmed Cu ions are univalent in the films.

scholarly journals ENHANCED FERROELECTRICITY AND FERROMAGNETISM OF (Y, Ni) CO-DOPED BiFeO3 MATERIALS

2018 ◽  
Vol 56 (1A) ◽  
pp. 219
Author(s):  
Dao Viet Thang
Keyword(s):  
Ferroelectric Properties ◽  
Sol Gel ◽  
Rhombohedral Structure ◽  
Ferromagnetic Behavior ◽  
X Ray Diffraction ◽  
X Ray ◽  
Co Doping ◽  
Saturation Polarization ◽  
Perovskite Type ◽  
Co Doped

In this study, multiferroicMultiferroic Bi1-xYxFe0.975Ni0.025O3 (x = 0.00, 0.05, 0.10, and 0.15) called as (Y, Ni)                co-doped BiFeO3 materials were synthesized by a sol-gel method.  and characterized by X-ray diffraction diagrams and(XRD), energy-dispersive X-ray (EDX) and vibrating sample magnetization (VSM) measurements demonstrated. The result showed that Bi1-xYxFe0.975Ni0.025O3all investigated materials waspresent a single phase of the perovskite-type rhombohedral structure. Ferromagnetism and ferroelectricity of the Bi1-xYxFe0.975Ni0.025O3 materials have been investigated. Results showed that the co-doping by (Y, Ni) for (Bi, Fe)  have affected in enhancing by the (Y, Ni) co-doping, as a result the ferroelectric polarization and magnetization of BiFeO3. The magnetic characterization indicated that the ferromagnetic behavior wasthe initial BiFeO3 materialwere enhanced with increasing concentration of Y3+ for (Y, Ni) co-substituted of BiFeO3. Which could beion. It is attributed to the defferentdifference of the magnetic momentmoments of Ni2+ and Fe3+, and+ ions, as well as the Y3+-Fe3+,+ and Y3+-Ni2+ super-exchange interaction. Theinteractions. The characteristics of the investigated materials, such as remanent magnetization (Mr), saturation magnetization (Ms), remanent polarization (2Pr) and saturation polarization (2Ps) continuously increase upon increasing in the range of x from 0.00 to 0.15. When x = 0.15, the values of Mr and Ms are 0.078 and 0.794 emu/g, respectively. The values of 2Pr and 2Ps are 16.58 and 27.99 µC/cm2, respectively. Origin of ferromagnetic and ferroelectric properties of Bi1-xYxFe0.975Ni0.025O3 materials will be discussed in this paper.

Structural and Luminescence Properties of Eu3+ and Dy3+ Doped Magnesium Tellurite Borophosphate Ceramic

2015 ◽  
Vol 1107 ◽  
pp. 53-58
Author(s):  
Siti Maisarah Aziz ◽  
Rosli Hussin ◽  
N.M. Yusoff
Keyword(s):  
Solid State ◽  
Emission Spectra ◽  
Solid State Reaction Method ◽  
Luminescence Properties ◽  
Functional Material ◽  
X Ray Diffraction ◽  
Co Doping ◽  
Powder Samples ◽  
Diffraction Patterns ◽  
Co Doped

Lately, researchers have been considering the miscellaneous in the borophosphate crystalline’s luminescence as one of the important properties in hunt of the new functional material. In this study we discus the structural and luminescence properties of Eu3+/Dy3+ co-doped borophosphate ceramic. A series of ceramic samples based on B2O3-(65-)P2O5-25MgO-10TeO2 where (065) mol has successfully been prepared using solid state reaction method and sintered at 900°C. The crystalline phase of the powder samples was characterized using X-ray diffraction pattern. The diffraction patterns analysis indicated that the prepared samples were polycrystalline phase of B(PO4), Mg(PO3)2and Mg(BO3)(PO4). The local structure network structure has been investigated using Infrared Spectroscopy using KBr method. The FT-Infrared spectra reveal the presence of B-O-B vibrations, BO3 and BO4 bridging oxygen and P-O stretching modes of P-O-P, P=O and PO4 unit in the ceramics sample. Meanwhile, the luminescence properties of doped sample were measured based on analysis of emission spectra of photoluminescence spectroscopy. The emission peaks of Eu3+ doped sample were located at 593 nm, 613 nm, 652 nm, 685 nm due to the assigned transition 5D0-7FJ( J = 1, 2, 3, 4 ). The Dy3+ emission is due to 4F9/2 -5H15/2 and 4F9/2-6H13/2 transition. For Eu3+/Dy3+ co-doped sample consists of peaks belonging to the 4F9/2-6H15/2 (482 nm) and 4F9/2-6H13/2 (573 nm) transition while red emission 5D0-7F2 transitions appears at 611 nm. Improvement in the optical properties due to co-doping may be useful to discover a new highly efficient luminescent material that are very useful in optical devices and solid-state lighting.

Silver Doped Nano-Sized Bioglass Ceramics: Synthesis, Characterization and Biocompatibility Studies

2016 ◽  
Vol 860 ◽  
pp. 25-28 ◽  
Author(s):  
Chinnasamy Ramaraj Mariappan ◽  
Narender Ranga
Keyword(s):  
Sol Gel ◽  
Glass Ceramics ◽  
X Ray Diffraction ◽  
Bending Vibrations ◽  
Tem Analysis ◽  
Transmission Electron ◽  
Visible Spectra ◽  
Calcium Phosphosilicate ◽  
Uv Visible

We report on the structural and biocompatibility properties of nanosized calcium phosphosilicate bioglass ceramics doped with 0, 2, 4 and 6 mol% Ag2O. Silver doped bioceramics were synthesized by sol-gel method. The prepared samples were characterized by means of powder X-ray diffraction (XRD), Fourier transform infrared (FTIR) spectroscopy, UV-visible and high resolution transmission electron microscopy. The XRD reveals the glass-ceramic nature of the samples. The FT-IR spectra show the possible stretching and bending vibrations of silicate and phosphate groups. Absorptions in UV-visible spectra reveal the silver embedment as Ag+/Ago form into the glass matrix. nanosize of the glass ceramics is confirmed by HR-TEM analysis. The bioactivity of silver doped bioceramics was investigated by in-vitro method with Dulbecco’s Modified Eagel’s Medium. It confirms the formation of bone-like hydroxylapatite layer formation on the surface of bioceramics.

Sign in / Sign up

Export Citation Format

Share Document