scholarly journals A Novel Specimen Produced by Additive Manufacturing for Pure Plane Strain Fatigue Crack Growth Studies

Metals ◽  
2021 ◽  
Vol 11 (3) ◽  
pp. 433
Author(s):  
Joel de Jesus ◽  
Micael Borges ◽  
Fernando Antunes ◽  
José Ferreira ◽  
Luis Reis ◽  
...  
Keyword(s):  
Fatigue Crack ◽  
Additive Manufacturing ◽  
Fatigue Crack Growth ◽  
Crack Growth ◽  
Plane Strain ◽  
Crack Front ◽  
Great Influence ◽  
Circular Crack ◽  
Internal Crack ◽  
Vacuum Equipment

Fatigue crack growth is usually studied using C(T) or M(T) specimens with through-thickness cracks. The objective of the present study is to propose a cylindrical specimen with central crack, produced by additive manufacturing. This geometry allows to have pure plane strain state along the whole crack front, avoiding the complexities associated with corner points, crack shape, and variation of crack closure along crack front. Additionally, this geometry may be used to develop studies in vacuum, avoiding expensive vacuum equipment, since the air is not in contact with the crack front. Cylindrical specimens of Ti6Al4V titanium alloy were produced by Selective Laser Melting and tested at a stress ratio R = 0. Marking with overloads was the solution adopted to measure the length of the internal cracks. The fracture surfaces presented circular crack fronts and the da/dN-DK curves showed a great influence of atmosphere on fatigue crack growth. An average difference of 50% was found between the results in air and vacuum. Therefore, this geometry with internal crack is an interesting alternative to through-thickness geometries.

Comparison of Computational Crack Path Predictions with Experimental Findings for a Quarter-Circular Surface Crack in a Shaft under Torsion

2007 ◽  
Vol 348-349 ◽  
pp. 161-164 ◽  
Author(s):  
Friedrich G. Buchholz ◽  
J. Wiebesiek ◽  
M. Fulland ◽  
Hans A. Richard
Keyword(s):  
Fatigue Crack ◽  
Fatigue Crack Growth ◽  
Crack Growth ◽  
Crack Front ◽  
Fracture Criterion ◽  
Circular Crack ◽  
Fe Model ◽  
Crack Growth Behaviour ◽  
3D Crack Growth ◽  
Experimental Findings

In this paper the rather complex 3D fatigue crack growth behaviour in a shaft with a quarter-circular crack under torsion is investigated by the aid of the programme ADAPCRACK3D and by application of a recently developed 3D fracture criterion. It will be shown that the computationally simulated results of fatigue crack growth in the FE-model of the shaft are in good agreement with experimental findings for the development of two anti-symmetric cracks, which originate from the two crack front corner points, that is where the crack front intersects the free surface of the cylindrical laboratory test-specimens. Consequently, also for this case with a rather complex 3D crack growth of two anti-symmetric cracks, the functionality of the ADAPCRACK3Dprogramme and the validity of the proposed 3D fracture criterion can be stated.

Comparison of DBEM and FEM Crack Path Predictions with Experimental Findings for a SEN-Specimen under Anti-Plane Shear Loading

2007 ◽  
Vol 348-349 ◽  
pp. 129-132 ◽  
Author(s):  
Roberto G. Citarella ◽  
Friedrich G. Buchholz
Keyword(s):  
Fatigue Crack ◽  
Fatigue Crack Growth ◽  
Crack Growth ◽  
Crack Front ◽  
Crack Path ◽  
Shear Loading ◽  
Crack Growth Behaviour ◽  
3D Crack Growth ◽  
Corner Points ◽  
Experimental Findings

In this paper detailed results of computational 3D fatigue crack growth simulations will be presented. The simulations for the crack path assessment are based on the DBEM code BEASY, and the FEM code ADAPCRACK 3D. The specimen under investigation is a SEN-specimen subject to pure anti-plane or out-of-plane four-point shear loading. The computational 3D fracture analyses deliver variable mixed mode II and III conditions along the crack front. Special interest is taken in this mode coupling effect to be found in stress intensity factor (SIF) results along the crack front. Further interest is taken in a 3D effect which is effective in particular at and adjacent to the two crack front corner points, that is where the crack front intersects the two free side surfaces of the specimen. Exactly at these crack front corner points fatigue crack growth initiates in the experimental laboratory test specimens, and develops into two separate anti-symmetric cracks with complex shapes, somehow similar to bird wings. The computational DBEM results are found to be in good agreement with these experimental findings and with FEM results previously obtained. Consequently, also for this new case, with complex 3D crack growth behaviour of two cracks, the functionality of the proposed DBEM and FEM approaches can be stated.

Three-Dimensional Study of Fatigue Crack Growth in a Rotating Disc

2013 ◽  
Vol 3 (2) ◽  
pp. 45-62
Author(s):  
Eskandari Hadi ◽  
Nami Mohammad Rahim
Keyword(s):  
Fatigue Crack ◽  
Fatigue Crack Growth ◽  
Crack Growth ◽  
Crack Front ◽  
Numerical Technique ◽  
Three Dimensional ◽  
Crack Orientation ◽  
Rotating Disc ◽  
Mesh Density ◽  
Three Dimensional Finite Element

The problem of fatigue-crack-growth in a rotating disc at different crack orientation angles is studied by using an automated numerical technique, which calculates the stress intensity factors on the crack front through the three-dimensional finite element method. Paris law is used to develop the fatigue shape of initially semi-elliptical surface crack. Because of needs for the higher mesh density and accuracy near the crack, the sub-modeling technique is used in the analysis. The distribution of SIF’s along the crack front at each step of growth is studied and the effect of crack orientation on the rate of crack-growth is investigated. The calculated SIF’s are reasonable and could be used to predict the probable crack growth rates in fracture mechanics analysis and can help engineers to consider in their designing and to prevent any unwanted failure of such components.

Automatic Fatigue Crack Growth

2009 ◽  
Author(s):  
S. C. Mellings ◽  
J. M. W. Baynham
Keyword(s):  
Fatigue Crack ◽  
Cyclic Loading ◽  
Fatigue Crack Growth ◽  
Crack Growth ◽  
Crack Front ◽  
Initial Crack ◽  
Design Stage ◽  
Load Spectrum ◽  
Forensic Investigations ◽  
Crack Faces

One of the critical requirements of fatigue crack growth simulation is calculation of the remaining life of a structure under cyclic loading. This paper presents a method which predicts the remaining fatigue life of a part, and gives information on the eventual mode of failure. The path of a growing crack needs to be understood so that informed assessment can be made of the structural consequences of eventual fast growth, and the likelihood of leakage and determination of leakage rates. For these reasons the use of standard handbook solutions for crack growth is generally not adequate, and it is essential to use the real geometry and loading. The reasons for performing such simulation work include preventive investigations performed at the design stage, forensic investigations performed after failure, and sometimes forensic investigations performed during failure-when the results provide input to the planning of remedial work. This paper focuses on the 3D simulation of cracks growing in metal structures exposed to cyclic loading, and explains the techniques which are used. The loading might arise from transients of pressure or other mechanical forces, or might be caused by thermal-stress variations. The simulation starts from an initial crack which can be of any size and orientation. The relevant geometry of the cracked component is modelled, and the loading is identified using one or more load cases together with a load spectrum which shows how the loading cycles. The effects of the crack are determined by calculating stress intensity factors at all positions along the crack front (it would be called the crack tip if the modelling was performed in 2D). The rate and direction of crack growth at each part of the crack front are calculated using one of the available crack growth laws, together with appropriate material properties. The effects of such growth are accumulated over a number of load cycles, and a new crack shape is determined. The process is repeated as required. The use of multi-axial and mixed mode techniques allows the crack to turn as a result of the applied loading, and the resulting crack path is therefore a consequence of both the detail of the geometry and the loading to which the structure is subjected. Gas or other fluid pressures acting on the crack faces can have significant impact, as can the contact between opposing crack faces when a load case causes part of the crack to close.

Fatigue Growth Prediction of Internal Surface Cracks in Pressure Vessels

1998 ◽  
Vol 120 (1) ◽  
pp. 17-23 ◽  
Author(s):  
X. B. Lin ◽  
R. A. Smith
Keyword(s):  
Fatigue Crack ◽  
Stress Intensity ◽  
Fatigue Crack Growth ◽  
Crack Growth ◽  
Crack Front ◽  
Internal Surface ◽  
Pressure Vessels ◽  
Surface Cracks ◽  
Elliptical Shape ◽  
Set Of Points

Fatigue crack growth was numerically simulated for various internal surface cracks with initially either semi-elliptical or irregular crack fronts. The simulation was directly based on a series of three-dimensional finite element analyses from which the stress intensity factors along the front of growing cracks were estimated. The fatigue crack growth law obtained from small laboratory specimens was incrementally integrated at a set of points along the crack front, and a new crack front was then re-established according to the local advances at this set of points by using a cubic spline curve. This method enabled the crack shape to be predicted without having to make the usual assumption of semi-elliptical shape. Fatigue analysis results are presented and discussed for fatigue shape developments and deviations from the semi-elliptical shape, aspect ratio changes, stress intensity factor variations during crack growth, and fatigue life predictions. Some of the results were also compared with those obtained by two simplified methods based on one and two degree-of-freedom models, respectively.

Sign in / Sign up

Export Citation Format

Share Document