scholarly journals Comparison of Properties and Bead Geometry in MIG and CMT Single Layer Samples for WAAM Applications

Metals ◽  
2021 ◽  
Vol 11 (10) ◽  
pp. 1530
Author(s):  
Harley Stinson ◽  
Richard Ward ◽  
Justin Quinn ◽  
Cormac McGarrigle
Keyword(s):  
Mechanical Properties ◽  
Arc Welding ◽  
Single Layer ◽  
Bead Geometry ◽  
Material Transfer ◽  
Cold Metal Transfer ◽  
Deposition Rates ◽  
Welding Processes ◽  
Wire Arc Additive Manufacturing ◽  
Process Mode

The process of Wire Arc Additive Manufacturing (WAAM) utilizes arc welding technology to fabricate metallic components by depositing material in a selective layered fashion. Several welding processes exist that can achieve this layered deposition strategy. Gas Metal Arc Welding (GMAW) derived processes are commonly favored for their high deposition rates (1–4 kg/h) and minimal torch reorientation required during deposition. A range of GMAW processes are available; all of which have different material transfer modes and thermal energy input ranges and the resultant metallic structures formed from these processes can vary in their mechanical properties and morphology. This work will investigate single-layer deposition and vary the process parameters and process mode to observe responses in mechanical properties, bead geometry and deposition rate. The process modes selected for this study were GMAW derived process of Metal Inert Gas (MIG) and Cold Metal Transfer (CMT). Characterization of parameter sets revealed relationships between torch travel speeds, wire feed speeds and the specimen properties and proportions. Differences were observed in the cross-sectional bead geometry and deposition rates when comparing MIG and CMT samples though the influence of process mode on mechanical properties was less significant compared to process parameter selection.

Control of humping phenomenon and analyzing mechanical properties of Al–Si wire-arc additive manufacturing fabricated samples using cold metal transfer process

2021 ◽  
pp. 095440622199840
Author(s):  
Yashwant Koli ◽  
N Yuvaraj ◽  
Aravindan Sivanandam ◽  
Vipin
Keyword(s):  
Mechanical Properties ◽  
Additive Manufacturing ◽  
Heat Input ◽  
Large Scale ◽  
High Deposition Rate ◽  
Bead Geometry ◽  
Layer By Layer ◽  
Cold Metal Transfer ◽  
Geometrical Shapes ◽  
Wire Arc Additive Manufacturing

Nowadays, rapid prototyping is an emerging trend that is followed by industries and auto sector on a large scale which produces intricate geometrical shapes for industrial applications. The wire arc additive manufacturing (WAAM) technique produces large scale industrial products which having intricate geometrical shapes, which is fabricated by layer by layer metal deposition. In this paper, the CMT technique is used to fabricate single-walled WAAM samples. CMT has a high deposition rate, lower thermal heat input and high cladding efficiency characteristics. Humping is a common defect encountered in the WAAM method which not only deteriorates the bead geometry/weld aesthetics but also limits the positional capability in the process. Humping defect also plays a vital role in the reduction of hardness and tensile strength of the fabricated WAAM sample. The humping defect can be controlled by using low heat input parameters which ultimately improves the mechanical properties of WAAM samples. Two types of path planning directions namely uni-directional and bi-directional are adopted in this paper. Results show that the optimum WAAM sample can be achieved by adopting a bi-directional strategy and operating with lower heat input process parameters. This avoids both material wastage and humping defect of the fabricated samples.

scholarly journals Wire Arc Additive Manufacturing (WAAM) of Aluminum Alloy AlMg5Mn with Energy-Reduced Gas Metal Arc Welding (GMAW)

Materials ◽  
2020 ◽  
Vol 13 (12) ◽  
pp. 2671 ◽  
Author(s):  
Maximilian Gierth ◽  
Philipp Henckell ◽  
Yarop Ali ◽  
Jonas Scholl ◽  
Jean Pierre Bergmann
Keyword(s):  
Mechanical Properties ◽  
Additive Manufacturing ◽  
Arc Welding ◽  
Energy Input ◽  
Large Scale ◽  
Unit Length ◽  
Gas Metal Arc Welding ◽  
Cold Metal Transfer ◽  
Metal Arc Welding ◽  
Wire Arc Additive Manufacturing

Large-scale aluminum parts are used in aerospace and automotive industries, due to excellent strength, light weight, and the good corrosion resistance of the material. Additive manufacturing processes enable both cost and time savings in the context of component manufacturing. Thereby, wire arc additive manufacturing (WAAM) is particularly suitable for the production of large volume parts due to deposition rates in the range of kilograms per hour. Challenges during the manufacturing process of aluminum alloys, such as porosity or poor mechanical properties, can be overcome by using arc technologies with adaptable energy input. In this study, WAAM of AlMg5Mn alloy was systematically investigated by using the gas metal arc welding (GMAW) process. Herein, correlations between the energy input and the resulting temperature–time-regimes show the effect on resulting microstructure, weld seam irregularities and the mechanical properties of additively manufactured aluminum parts. Therefore, multilayer walls were built layer wise using the cold metal transfer (CMT) process including conventional CMT, CMT advanced and CMT pulse advanced arc modes. These processing strategies were analyzed by means of energy input, whereby the geometrical features of the layers could be controlled as well as the porosity to area portion to below 1% in the WAAM parts. Furthermore, the investigations show the that mechanical properties like tensile strength and material hardness can be adapted throughout the energy input per unit length significantly.

Effect of Different Arc Welding Processes on the Metallurgical and Mechanical Properties of Ramor 500 Armor Steel

2019 ◽  
Vol 142 (2) ◽  
Author(s):  
Ali Günen ◽  
Selçuk Bayar ◽  
Mustafa Serdar Karakaş
Keyword(s):  
Mechanical Properties ◽  
Welded Joints ◽  
Arc Welding ◽  
Impact Resistance ◽  
Welding Process ◽  
Fusion Welding ◽  
Minor Amount ◽  
Cold Metal Transfer ◽  
Armor Steel ◽  
Welding Processes

Abstract In the present study, Ramor 500 armor steel plates were automatically welded using cold metal transfer arc welding (CMT), gas metal arc welding (GMAW), and hybrid plasma arc welding (HPAW) methods. To investigate the effects of three different fusion welding methods on metallurgical and mechanical properties, the welded joints were examined using optical microscopy, scanning electron microscopy (SEM), and energy-dispersive spectroscopy (EDS) and also subjected to radiographic, hardness, tensile, and notched impact tests. The weld metal (WM) region of the GMAW and HPAW joints consisted of massive austenite. In the CMT welded joint, the WM consisted mainly of dendritic austenite and a minor amount of δ-ferrite. Regardless of the welding process, the hardness of both the WM and heat-affected zone (HAZ) regions was found to be higher than the base metal (BM). The tensile strengths obtained by CMT, GMAW, and HPAW were 45%, 50%, and 65% of the BM, respectively. Cleavage-type brittle fractures occurred in the GMAW and HPAW welded joints, while localized ductile fractures occurred in the CMT joints. Tensile test specimens of the CMT joints fractured in the WM, while the GMAW and HPAW joints fractured in the HAZ. In terms of notch toughness, the CMT joints exhibited better impact resistance compared with the BM. GMAW and HPAW joints displayed less impact resistance than the BM, with values comparable with previous studies in the literature.

Application of Low Heat Input Gas Metal Arc Welding for Corrosion Resistant Weld Overlays

2020 ◽  
Author(s):  
Timothy Babyak ◽  
Vincent DeCenso ◽  
Boian Alexandrov ◽  
Jorge Penso
Keyword(s):  
Heat Input ◽  
Arc Welding ◽  
Oil And Gas Industry ◽  
Welding Parameters ◽  
Cold Metal Transfer ◽  
Widespread Application ◽  
Deposition Rates ◽  
Corrosion Resistant ◽  
Welding Processes ◽  
Weld Overlays

Abstract Preventing failure due to corrosion poses a challenge to the oil and gas industry. A cost-effective way to prevent such failures is the application of corrosion-resistant nickel-based weld overlays using arc welding processes. Previous research performed at The Ohio State University indicates low heat input GMAW processes, such as cold metal transfer (CMT), produce weld overlays which corrode up to ten times slower than overlays produced with cold wire GTAW [1, 2], with up to ten times higher deposition rates [3]. However, formation of lack of fusion and lack of penetration defects has been a major concern related to the widespread application of low heat input GMAW processes in the industry. In this study, optimal windows of CMT welding parameters for producing defect-free welds were established using a design of experiment approach. CMT weld overlays were compared with hot wire (HW)-GTAW overlays currently used in industry with respect to bead characteristics, microstructure, and process capability. As compared with the HW-GTAW process, the CMT process produced weld overlays with up to four times lower dilution, seven times smaller interdendritic arm spacing, and four times higher deposition rates. Additionally, average heat affected zone and fusion boundary hardness values in the CMT overlays were below 248 HV0.1 and may not require the post weld heat treatment specified by NACE MR0175.

scholarly journals Building strategy effect on mechanical properties of high strength low alloy steel in wire + arc additive manufacturing

2020 ◽  
Vol 65 (3) ◽  
pp. 125-136
Author(s):  
Yildiz Suat ◽  
Baris Koc ◽  
Oguzhan Yilmaz
Keyword(s):  
Mechanical Properties ◽  
Additive Manufacturing ◽  
Yield Strength ◽  
High Strength ◽  
Inert Gas ◽  
High Deposition Rate ◽  
Thin Wall ◽  
Cold Metal Transfer ◽  
Welding Processes ◽  
Wire Arc Additive Manufacturing

Wire arc additive manufacturing (WAAM) which is literally based on continuously fed material deposition type of welding processes such as metal inert gas (MIG), tungsten inert gas (TIG) and plasma welding, is a variant of additive manufacturing technologies. WAAM steps forward with its high deposition rate and low equipment cost as compared to the powder feed and laser/electron beam heated processes among various additive manufacturing processes. In this work, sample parts made of low allow high strength steel (ER120S-G) was additively manufactured via WAAM method using robotic cold metal transfer technology (CMT). The process parameters and building strategies were investigated and correlated with the geometrical, metallurgical and mechanical properties on the produced wall geometries. The results obtained from the thin wall sample parts have showed that with increasing heat input, mechanical properties decreases, since higher heat accumulation and lower cooling rate increases the grain size. The tensile tests results have showed that casting steel (G24Mn6+QT2) mechanical properties which requires 500 MPa yield strength can be compared to with as build WAAM process having 640 MPa yield strength. Tensile strength were fulfilled for S690Q and yield strength is very close to the reference value.

scholarly journals Effect of Filler Metal Type on Microstructure and Mechanical Properties of Fabricated NiAl Bronze Alloy Using Wire Arc Additive Manufacturing System

Metals ◽  
2021 ◽  
Vol 11 (3) ◽  
pp. 513
Author(s):  
Jae Won Kim ◽  
Jae-Deuk Kim ◽  
Jooyoung Cheon ◽  
Changwook Ji
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Additive Manufacturing ◽  
Filler Metal ◽  
Gas Metal Arc Welding ◽  
Metal Wire ◽  
Cold Metal Transfer ◽  
Metal Type ◽  
Cold Metal ◽  
Wire Arc Additive Manufacturing

This study observed the effect of filler metal type on mechanical properties of NAB (NiAl-bronze) material fabricated using wire arc additive manufacturing (WAAM) technology. The selection of filler metal type is must consider the field condition, mechanical properties required by customers, and economics. This study analyzed the bead shape for representative two kind of filler metal types use to maintenance and fabricated a two-dimensional bulk NAB material. The cold metal transfer (CMT) mode of gas metal arc welding (GMAW) was used. For a comparison of mechanical properties, the study obtained three specimens per welding direction from the fabricated bulk NAB material. In the tensile test, the NAB material deposited using filler metal wire A showed higher tensile strength and lower elongation (approx. +71 MPa yield strength, +107.1 MPa ultimate tensile strength, −12.4% elongation) than that deposited with filler metal wire B. The reason is that, a mixture of tangled fine α platelets and dense lamellar eutectoid α + κIII structure with β´ phases was observed in the wall made with filler metal wire A. On the other hand, the wall made with filler metal wire B was dominated by coarse α phases and lamellar eutectoid α + κIII structure in between.

scholarly journals Characterisation of a High-Performance Al–Zn–Mg–Cu Alloy Designed for Wire Arc Additive Manufacturing

Materials ◽  
2020 ◽  
Vol 13 (7) ◽  
pp. 1610 ◽  
Author(s):  
Paulo J. Morais ◽  
Bianca Gomes ◽  
Pedro Santos ◽  
Manuel Gomes ◽  
Rudolf Gradinger ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Additive Manufacturing ◽  
High Performance ◽  
Mechanical Performance ◽  
Fluorescence Analysis ◽  
Cold Metal Transfer ◽  
Direction Parallel ◽  
X Ray ◽  
Wire Arc Additive Manufacturing

Ever-increasing demands of industrial manufacturing regarding mechanical properties require the development of novel alloys designed towards the respective manufacturing process. Here, we consider wire arc additive manufacturing. To this end, Al alloys with additions of Zn, Mg and Cu have been designed considering the requirements of good mechanical properties and limited hot cracking susceptibility. The samples were produced using the cold metal transfer pulse advanced (CMT-PADV) technique, known for its ability to produce lower porosity parts with smaller grain size. After material simulations to determine the optimal heat treatment, the samples were solution heat treated, quenched and aged to enhance their mechanical performance. Chemical analysis, mechanical properties and microstructure evolution were evaluated using optical light microscopy, scanning electron microscopy, energy dispersive X-ray spectroscopy, X-ray fluorescence analysis and X-ray radiography, as well as tensile, fatigue and hardness tests. The objective of this research was to evaluate in detail the mechanical properties and microstructure of the newly designed high-performance Al–Zn-based alloy before and after ageing heat treatment. The only defects found in the parts built under optimised conditions were small dispersed porosities, without any visible cracks or lack of fusion. Furthermore, the mechanical properties are superior to those of commercial 7xxx alloys and remarkably independent of the testing direction (parallel or perpendicular to the deposit beads). The presented analyses are very promising regarding additive manufacturing of high-strength aluminium alloys.

Sign in / Sign up

Export Citation Format

Share Document