scholarly journals MHD Stagnation Point on Nanofluid Flow and Heat Transfer of Carbon Nanotube over a Shrinking Surface with Heat Sink Effect

Molecules ◽  
2021 ◽  
Vol 26 (24) ◽  
pp. 7441
Author(s):  
Mohamad Nizam Othman ◽  
Alias Jedi ◽  
Nor Ashikin Abu Bakar
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Carbon Nanotube ◽  
Stagnation Point ◽  
Heat Sink ◽  
Magnetic Parameter ◽  
Volume Fraction ◽  
Flow And Heat Transfer ◽  
Sink Effect ◽  
Shrinking Surface

This study is to investigate the magnetohydrodynamic (MHD) stagnation point flow and heat transfer characteristic nanofluid of carbon nanotube (CNTs) over the shrinking surface with heat sink effects. Similarity equations deduced from momentum and energy equation of partial differential equations are solved numerically. This study looks at the different parameters of the flow and heat transfer using first phase model which is Tiwari-Das. The parameter discussed were volume fraction nanoparticle, magnetic parameter, heat sink/source parameters, and a different type of nanofluid and based fluids. Present results revealed that the rate of nanofluid (SWCNT/kerosene) in terms of flow and heat transfer is better than (MWCNT/kerosene) and (CNT/water) and regular fluid (water). Graphically, the variation results of dual solution exist for shrinking parameter in range λc<λ≤−1 for different values of volume fraction nanoparticle, magnetic, heat sink parameters, and a different type of nanofluid. However, a unique solution exists at −1<λ<1, and no solutions exist at λ<λc which is a critical value. In addition, the local Nusselt number decreases with increasing volume fraction nanoparticle when there exists a heat sink effect. The values of the skin friction coefficient and local Nusselt number increase for both solutions with the increase in magnetic parameter. In this study, the investigation on the flow and heat transfer of MHD stagnation point nanofluid through a shrinking surface with heat sink effect shows how important the application to industrial applications.

Numerical solutions of non-alignment stagnation-point flow and heat transfer over a stretching/shrinking surface in a nanofluid

2016 ◽  
Vol 26 (6) ◽  
pp. 1747-1767 ◽  
Author(s):  
Ioan Pop ◽  
Kohi Naganthran ◽  
Roslinda Nazar
Keyword(s):  
Heat Transfer ◽  
Differential Equations ◽  
Stagnation Point ◽  
Numerical Solutions ◽  
Dual Solutions ◽  
Stagnation Point Flow ◽  
Content Type ◽  
Boundary Layer Equations ◽  
Flow And Heat Transfer ◽  
Shrinking Surface

Purpose – The purpose of this paper is to analyse numerically the steady stagnation-point flow of a viscous and incompressible fluid over continuously non-aligned stretching or shrinking surface in its own plane in a water-based nanofluid which contains three different types of nanoparticles, namely, Cu, Al2O3 and TiO2. Design/methodology/approach – Similarity transformation is used to convert the system of boundary layer equations which are in the form of partial differential equations into a system of ordinary differential equations. The system of similarity governing equations is then reduced to a system of first-order differential equations and solved numerically using the bvp4c function in Matlab software. Findings – Unique solution exists when the surface is stretched and dual solutions exist as the surface shrunk. For the dual solutions, stability analysis has revealed that the first solution (upper branch) is stable and physically realizable, while the second solution (lower branch) is unstable. The effect of non-alignment is huge for the shrinking surface which is in contrast with the stretching surface. Practical implications – The results obtained can be used to explain the characteristics and applications of nanofluids, which are widely used as coolants, lubricants, heat exchangers and micro-channel heat sinks. This problem also applies to some situations such as materials which are manufactured by extrusion, production of glass-fibre and shrinking balloon. In this kind of circumstance, the rate of cooling and the stretching/shrinking process play an important role in moulding the final product according to preferable features. Originality/value – The present results are original and new for the study of fluid flow and heat transfer over a stretching/shrinking surface for the problem considered by Wang (2008) in a viscous fluid and extends to nanofluid by using the Tiwari and Das (2007) model.

scholarly journals Magnetohydrodynamic Flow and Heat Transfer Induced by a Shrinking Sheet

Mathematics ◽  
2020 ◽  
Vol 8 (7) ◽  
pp. 1175
Author(s):  
Nor Ain Azeany Mohd Nasir ◽  
Anuar Ishak ◽  
Ioan Pop
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Differential Equations ◽  
Prandtl Number ◽  
Heat Generation ◽  
Local Nusselt Number ◽  
Magnetic Parameter ◽  
Skin Friction Coefficient ◽  
Shrinking Sheet ◽  
Flow And Heat Transfer

The magnetohydrodynamic (MHD) stagnation point flow over a shrinking or stretching flat sheet is investigated. The governing partial differential equations (PDEs) are reduced into a set of ordinary differential equations (ODEs) by a similarity transformation and are solved numerically with the help of MATLAB software. The numerical results obtained are for different values of the magnetic parameter M, heat generation parameter Q, Prandtl number Pr and reciprocal of magnetic Prandtl number ε. The influences of these parameters on the flow and heat transfer characteristics are investigated and shown in tables and graphs. Two solutions are found for a certain rate of the shrinking strength. The stability of the solutions in the long run is determined, and shows that only one of them is stable. It is found that the skin friction coefficient f ″ ( 0 ) and the local Nusselt number − θ ′ ( 0 ) decrease as the magnetic parameter M increases. Further, the local Nusselt number increases as the heat generation increases.

Hybrid nanofluid flow and heat transfer over a nonlinear permeable stretching/shrinking surface

2019 ◽  
Vol 29 (9) ◽  
pp. 3110-3127 ◽  
Author(s):  
Iskandar Waini ◽  
Anuar Ishak ◽  
Ioan Pop
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Friction Coefficient ◽  
Skin Friction ◽  
Local Nusselt Number ◽  
Skin Friction Coefficient ◽  
Hybrid Nanofluid ◽  
Content Type ◽  
Flow And Heat Transfer ◽  
Shrinking Surface

PurposeThis paper aims to investigate the steady flow and heat transfer of a Cu-Al2O3/water hybrid nanofluid over a nonlinear permeable stretching/shrinking surface with radiation effects. The surface velocity condition is assumed to be of the power-law form with an exponent of 1/3. The governing equations of the problem are converted into a system of similarity equations by using a similarity transformation.Design/methodology/approachThe problem is solved numerically using the boundary value problem solver (bvp4c) in Matlab software. The results of the skin friction coefficient and the local Nusselt number as well as the velocity and temperature profiles are presented through graphs and tables for several values of the parameters. The effects of these parameters on the flow and heat transfer characteristics are examined and discussed.FindingsResults found that dual solutions exist for a certain range of the stretching/shrinking and suction parameters. The increment of the skin friction coefficient and reduction of the local Nusselt number on the shrinking sheet is observed with the increasing of copper (Cu) nanoparticle volume fractions for the upper branch. The skin friction coefficient and the local Nusselt number increase when suction parameter is increased for the upper branch. Meanwhile, the temperature increases in the presence of the radiation parameter for both branches.Originality/valueThe problem of Cu-Al2O3/water hybrid nanofluid flow and heat transfer over a nonlinear permeable stretching/shrinking surface with radiation effects is the important originality of the present study where the dual solutions for the flow reversals are obtained.

MHD nanofluid heat transfer between a stretching sheet and a porous surface using neural network approach

2019 ◽  
Vol 30 (06) ◽  
pp. 1950048 ◽  
Author(s):  
Yuancheng Geng ◽  
A. Hassanvand ◽  
Mostafa Monfared ◽  
Rasoul Moradi
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Nusselt Number ◽  
Magnetic Parameter ◽  
Volume Fraction ◽  
Sensitivity Analyses ◽  
Integration Scheme ◽  
Group Method ◽  
Suction Parameter ◽  
Wall Injection

Magnetohydrodynamic flow of nanofluids and heat transfer between two horizontal plates in a rotating system have been examined numerically. In order to do this, the group method of data handling (GMDH)-type neural networks is used to calculate Nusselt number formulation. Results indicate that GMDH-type NN in comparison with fourth-order Runge–Kutta integration scheme provides an effective means of efficiently recognizing the patterns in data and accurately predicting a performance. Single-phase model is used in this study. Similar solution is used in order to obtain ordinary differential equation. The effects of nanoparticle volume fraction, magnetic parameter, wall injection/suction parameter and Reynolds number on Nusselt number are studied by sensitivity analyses. The results show that Nusselt number is an increasing function of Reynolds number and volume fraction of nanoparticles but it is a decreasing function of magnetic parameter. Also, it can be found that wall injection/suction parameter has no significant effect on rate of heat transfer.

The effect of viscous dissipation on laminar nanofluid flow in a microchannel heat sink

2009 ◽  
Vol 223 (11) ◽  
pp. 2697-2706 ◽  
Author(s):  
M Ghazvini ◽  
M A Akhavan-Behabadi ◽  
M Esmaeili
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Viscous Dissipation ◽  
Heat Sink ◽  
Volume Fraction ◽  
Numerical Study ◽  
Microchannel Heat Sink ◽  
Fluid Temperature ◽  
Nanofluid Flow ◽  
Aspect Ratios

The present article focuses on analytical and numerical study on the effect of viscous dissipation when nanofluid is used as the coolant in a microchannel heat sink (MCHS). The nanofluid is made from CuO nanoparticles and water. To analyse the MCHS, a modified Darcy equation for the fluid and two-equation model for heat transfer between fluid and solid sections are employed in porous media approach. In addition, to deal with nanofluid heat transfer, a model based on the Brownian motion of nanoparticles is used. The model evaluates the thermal conductivity of nanofluid considering the thermal boundary resistance, nanoparticle diameter, volume fraction, and the fluid temperature. At first, the effects of particle volume fraction on temperature distribution and overall heat transfer coefficient are investigated with and without considering viscous dissipation. After that, the influence of different channel aspect ratios and porosities is studied. The results show that for nanofluid flow in microchannels, the viscous dissipation can be neglected for low volume fractions and aspect ratios only. Finally, the effect of porosity and Brinkman number on the overall Nusselt number is studied, where asymptotic behaviour of the Nusselt number is observed and discussed from the energy balance point of view.

scholarly journals Flow and Heat Transfer in Micro Pin Fin Heat Sinks With Nano-Encapsulated Phase Change Materials

2016 ◽  
Vol 138 (6) ◽  
Author(s):  
Bahram Rajabifar ◽  
Hamid Reza Seyf ◽  
Yuwen Zhang ◽  
Sanjeev K. Khanna
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Phase Change ◽  
Wall Temperature ◽  
Phase Change Materials ◽  
Euler Number ◽  
Volume Fraction ◽  
Inlet Velocity ◽  
Pin Fin ◽  
Flow And Heat Transfer

In this paper, a 3D-conjugated heat transfer model for nano-encapsulated phase change materials (NEPCMs) cooled micro pin fin heat sink (MPFHS) is presented. The governing equations of flow and heat transfer are solved using a finite volume method based on collocated grid and the results are validated with the available data reported in the literature. The effect of nanoparticles volume fraction (C = 0.1, 0.2, and 0.3), inlet velocity (Vin = 0.015, 0.030, and 0.045 m/s), and bottom wall temperature (Twall = 299.15, 303.15, 315.15, and 350.15 K) is studied on Nusselt and Euler numbers as well as temperature contours in the system. The results indicate that significant heat transfer enhancement is achieved when using the NEPCM slurry as an advanced coolant. The maximum Nusselt number when NEPCM slurry (C = 0.3) with Vin = 0.015, 0.030, and 0.045 (m/s) is employed is 2.27, 1.81, and 1.56 times higher than the ones with base fluid, respectively. However, with increasing bottom wall temperature, the Nusselt number first increases then decreases. The former is due to higher heat transfer capability of coolant at temperatures over the melting range of phase change material (PCM) particles due to partial melting of nanoparticles in this range. However, the latter phenomenon is due to the lower capability of the NEPCM particles and consequently coolant in absorbing heat at coolant temperatures is higher than the temperature correspond to fully melted NEPCM. It was observed that the NEPCM slurry has a drastic effect on the Euler number, and with increasing volume fraction and decreasing inlet velocity, the Euler number increases accordingly.

scholarly journals MHD Stagnation Point Flow and Heat Transfer Over a Stretching Sheet in a Blood-Based Casson Ferrofluid With Newtonian Heating

2021 ◽  
Vol 82 (1) ◽  
pp. 1-11
Author(s):  
Muhammad Khairul Anuar Mohamed ◽  
Siti Hanani Mat Yasin ◽  
Mohd Zuki Salleh ◽  
Hamzeh Taha Alkasasbeh
Keyword(s):  
Heat Transfer ◽  
Stagnation Point ◽  
Stretching Sheet ◽  
Volume Fraction ◽  
Mhd Flow ◽  
Casson Fluid ◽  
Skin Friction Coefficient ◽  
Newtonian Heating ◽  
Linear Partial Differential Equations ◽  
Flow And Heat Transfer

The present study investigated the magnetohydrodynamic (MHD) flow and heat transfer on a stagnation point past a stretching sheet in a blood-based Casson ferrofluid with Newtonian heating boundary conditions. The ferrite Fe3O4 and cobalt ferrite CoFe2O4 ferroparticles suspended into Casson fluid represent by human blood to form blood-based Casson ferrofluid are numerically examined. The mathematical model for Casson ferrofluid which is in non-linear partial differential equations are first transformed to a more convenient form by similarity transformation approach then solved numerically by using the Runge-Kutta-Fehlberg (RKF45) method. The characteristics and effects of the stretching parameter, the magnetic parameter, the Casson parameter and the ferroparticle volume fraction for Fe3O4 and CoFe2O4 on the variation of surface temperature and the reduced skin friction coefficient are analyzed and discussed. It is found that the blood-based Casson ferrofluid provided up to 46% higher in temperature surface compared to blood-based fluid with the presence of magnetic effects.

scholarly journals Homann Stagnation Point Flow and Heat Transfer of Hybrid Nanofluids Over a Permeable Radially Stretching/Shrinking Sheet

2021 ◽  
Vol 85 (1) ◽  
pp. 101-112
Author(s):  
Yap Bing Kho ◽  
Rahimah Jusoh ◽  
Mohd Zuki Salleh ◽  
Mohd Hisyam Ariff ◽  
Ioan Pop
Keyword(s):  
Heat Transfer ◽  
Differential Equations ◽  
Stagnation Point ◽  
Volume Fraction ◽  
Stagnation Point Flow ◽  
Shrinking Sheet ◽  
Nanoparticle Volume Fraction ◽  
Flow And Heat Transfer ◽  
Hybrid Nanofluids ◽  
Water Base

The steady two-dimensional Homan stagnation point flow and heat transfer of water base hybrid nanofluids (Al2O3 & Cu) over a permeable radially stretching/shrinking sheet have been studied. The similarity variables are introduced to transform the partial differential equations of the model into the ordinary differential equations. Numerical findings and dual solutions have been carried out by implementing the bvp4c code through MATLAB software. The most prominent effect is illustrated in the boundary layer thickness where the velocity profile increases upon the increment of the suction intensity but decreases in the temperature profile. Besides, the reduced Nusselt number also decreases as enlarging the value of copper and alumina nanoparticle volume fraction. The analysis of the first and second solutions are presented graphically with critical values as well as the detail discussions on the effects of the other involving parameters.

Impact of Stretching and Penetration of Walls on Nanofluid Flow and Heat Transfer in a Rotating System

2018 ◽  
Vol 387 ◽  
pp. 37-50 ◽  
Author(s):  
A.S. Dogonchi ◽  
D.D. Ganji ◽  
Oluwole Daniel Makinde
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Differential Equations ◽  
Heat Source ◽  
Volume Fraction ◽  
Radiation Parameter ◽  
Rotating System ◽  
Nanofluid Flow ◽  
Linear Ordinary Differential Equations ◽  
Flow And Heat Transfer

Nanofluid flow and heat transfer in a rotating system between two parallel plates in the presence of thermal radiation and heat source impacts are examined. One of the plates of the considered system is penetrable and the other one is stretchable or shrinkable. A similarity transformation is used to convert the governing momentum and energy equations into non-linear ordinary differential equations with the relevant boundary conditions. The achieved non-linear ordinary differential equations are solved by Duan-Rach Approach (DRA). This method allows us to realize a solution without applying numerical methods to evaluate the unspecified coefficients. The impacts of diverse active parameters such as the stretching/shrinking parameter, the radiation parameter, the heat source parameter, the suction/blowing parameter, the Reynolds number and the volume fraction of nanofluid on the velocity and temperature profiles are explored. Also, the correlation for the Nusselt number has been developed in terms of active parameters of the present study. The outcomes indicate that the Nusselt number is a raising function of the injection parameter, nanofluid volume fraction and the radiation parameter, while it is a decreasing function of the suction and heat source parameters. Furthermore, for injection case by soaring the shrinking parameter, the probability of occurrence of the backflow phenomenon soars.

scholarly journals Parametric Investigation on a Micro-Array Heat Sink with Staggered Trapezoidal Bumps

Micromachines ◽  
2019 ◽  
Vol 10 (12) ◽  
pp. 845 ◽  
Author(s):  
Ruijin Wang ◽  
Weijia Yuan ◽  
Jiawei Wang ◽  
Zefei Zhu
Keyword(s):  
Heat Transfer ◽  
Heat Sink ◽  
Volume Fraction ◽  
Rake Angle ◽  
Heat Sinks ◽  
Transfer Enhancement ◽  
Flow And Heat Transfer ◽  
Microelectronic Devices ◽  
Chaotic Convection ◽  
Micro Array

More efficient heat sinks are required due to the rapid increase of power density in microelectronic devices. In this study, a micro-array heat sink with stagger trapezoidal bumps was designed. Numerical simulations for the flow and heat transfer under various conditions were carried out to help us to fully understand the mechanisms of the heat transfer enhancement in such a heat sink. The effects of the structure of the heat sink, parameters of the bumps, and volume fraction of the nanofluid on the performance of heat sink were studied. The results show us that the bumps in the heat sink can result in chaotic convection, interrupting the thermal boundary layer and increasing the cooling area, subsequently improving the heat transfer performance. Furthermore, parametric investigations for trapezoidal bumps were conducted to obtain preferential values for parameters, such as the bump width, fore rake angle of the bump, bump height, and bump pitch.

Sign in / Sign up

Export Citation Format

Share Document