scholarly journals 3D Printed Fully Recycled TiO2-Polystyrene Nanocomposite Photocatalysts for Use against Drug Residues

Nanomaterials ◽  
2020 ◽  
Vol 10 (11) ◽  
pp. 2144
Author(s):  
Maria Sevastaki ◽  
Mirela Petruta Suchea ◽  
George Kenanakis
Keyword(s):  
Tio2 Nanoparticles ◽  
Large Scale ◽  
Fused Deposition Modeling ◽  
Low Cost ◽  
Real Life ◽  
3D Printer ◽  
Alternative Route ◽  
Fused Deposition ◽  
Deposition Modeling ◽  
3D Printed

In the present work, the use of nanocomposite polymeric filaments based on 100% recycled solid polystyrene everyday products, enriched with TiO2 nanoparticles with mass concentrations up to 40% w/w, and the production of 3D photocatalytic structures using a typical fused deposition modeling (FDM)-type 3D printer are reported. We provide evidence that the fabricated 3D structures offer promising photocatalytic properties, indicating that the proposed technique is indeed a novel low-cost alternative route for fabricating large-scale photocatalysts, suitable for practical real-life applications.

scholarly journals Typography-Like 3D-Printed Templates for the Lithography-Free Fabrication of Microfluidic Chips

2019 ◽  
Vol 25 (1) ◽  
pp. 82-87
Author(s):  
Wenqiong Su ◽  
Yulong Li ◽  
Lulu Zhang ◽  
Jiahui Sun ◽  
Shuopeng Liu ◽  
...  
Keyword(s):  
Processing Time ◽  
Fused Deposition Modeling ◽  
Three Dimensional ◽  
Cost Effective ◽  
Microfluidic Channels ◽  
3D Printer ◽  
Microfluidic Chips ◽  
Fused Deposition ◽  
Deposition Modeling ◽  
3D Printed

Typography-like templates for polydimethylsiloxane (PDMS) microfluidic chips using a fused deposition modeling (FDM) three-dimensional (3D) printer are presented. This rapid and fast proposed scheme did not require complicated photolithographic fabrication facilities and could deliver resolutions of ~100 μm. Polylactic acid (PLA) was adopted as the material to generate the 3D-printed units, which were then carefully assembled on a glass substrate using a heat-melt-curd strategy. This craft of bonding offers a cost-effective way to design and modify the templates of microfluidic channels, thus reducing the processing time of microfluidic chips. Finally, a flexible microfluidic chip to be employed for cell-based drug screening was developed based on the modularized 3D-printed templates. The lithography-free, typography-like, 3D-printed templates create a modularized fabrication process and promote the prevalence of integrated microfluidic systems with minimal requirements and improved efficiency.

scholarly journals Z-axis limit switch 3D printer

2020 ◽  
pp. 22-27
Author(s):  
Vadym Shalenko ◽  
Boris Korniychuk ◽  
Andriі Masluyk
Keyword(s):  
3D Printing ◽  
Large Scale ◽  
Fused Deposition Modeling ◽  
Selective Laser Sintering ◽  
3D Printer ◽  
Fused Deposition ◽  
Laminated Object Manufacturing ◽  
The Future ◽  
Deposition Modeling ◽  
Additive Methods

Not much time has passed since the appearance of the first 3D printer. Today there are many different printers. They differ in various 3D printing technologies, namely: Stereolithography – SL, Selective Laser Sintering, Fused Deposition Modeling – FDM, Laminated Object Manufacturing – LOM, Polyjet and Ployjet Matrix. In recent years, the spread of 3D printing technology has become and continues to be used more and more today. Of course, in the future we will see a large-scale spread of additive methods, but the practical application of 3D printing today is available to everyone. Melting deposition modeling technologies have become widespread and available. The authors in this article consider possible options for upgrading the mounting of the end sensor of the Z Axis and automating the process of calibration of the zero gap of the extruder nozzle relative to the working surface of the printer. This calibration is important. This affects the accuracy and printing process of the future plastic model. During the operation of the 3D printer, it is often necessary to service the extruder, which forces the process of calibrating the zero gap of the printer nozzle. Optimally correct selected nozzle clearance affects the accuracy, geometry of the model and printing as a whole. It also allows you to get rid of peeling off the model from the desktop surface and the destruction of the model during printing.

scholarly journals Design and Validation of an Open Source 3D Printer Based on Digital Ultraviolet Light Processing (DLP), for the Improvement of Traditional Artistic Casting Techniques for Microsculptures

2021 ◽  
Vol 11 (7) ◽  
pp. 3197
Author(s):  
Jose Luis Saorin ◽  
Manuel Drago Diaz-Alemán ◽  
Jorge De la Torre-Cantero ◽  
Cecile Meier ◽  
Ithaisa Pérez Conesa
Keyword(s):  
Open Source ◽  
Ultraviolet Light ◽  
Fused Deposition Modeling ◽  
Liquid Crystal Display ◽  
Low Cost ◽  
3D Printer ◽  
Digital Light Processing ◽  
Fused Deposition ◽  
3D Printers ◽  
Deposition Modeling

The adoption of open-source digital manufacturing technologies in small art workshops may improve their competitiveness. Pieces modeled by computer and made with FDM (Fused Deposition Modeling) 3D printers that use PLA (polylactic acid) can be implemented in the procedures of artistic casting. However, models printed by PLA are limited to approximate minimum sizes of 3 cm, and the optimal layer height resolution is 0.1 mm. These sizes and resolutions are not suitable for creating microsculptures used, in many cases, in jewelry. An alternative to solve this limitation, is to use a DMLS (Direct Metal Laser Sintering) 3D printer. However, due to its high cost, it is a technology that is difficult to introduce in small artistic foundries. This work detailed the design and validation of a DLP (Digital Light Processing) 3D printer, using backlit LCD (Liquid Crystal Display) screens with ultraviolet light. Its development is totally “open source” and is proposed as a kit made up of electronic components, based on Arduino and easy to access mechanical components in the market. Most parts can be manufactured in low cost FDM (Fused Deposition Modeling) 3D printers. The result is an affordable, high resolution (0.021 mm), and open-design printer that can be implemented in artistic contexts.

scholarly journals Flexible 3D Printed Conductive Metamaterial Units for Electromagnetic Applications in Microwaves

Materials ◽  
2020 ◽  
Vol 13 (17) ◽  
pp. 3879
Author(s):  
Anna C. Tasolamprou ◽  
Despoina Mentzaki ◽  
Zacharias Viskadourakis ◽  
Eleftherios N. Economou ◽  
Maria Kafesaki ◽  
...  
Keyword(s):  
Fused Deposition Modeling ◽  
Low Cost ◽  
Three Dimensional ◽  
Dielectric Materials ◽  
Ring Resonators ◽  
Free Standing ◽  
Fused Deposition ◽  
Structural Details ◽  
Deposition Modeling ◽  
3D Printed

In this work we present a method for fabricating three dimensional, ultralight and flexible millimeter metamaterial units using a commercial household 3D printer. The method is low-cost, fast, eco-friendly and accessible. In particular, we use the Fused Deposition Modeling 3D printing technique and we fabricate flexible conductive Spilt Ring Resonators (SRRs) in a free-standing form. We characterized the samples experimentally through measurements of their spectral transmission, using standard rectangular microwave waveguides. Our findings show that the resonators produce well defined resonant electromagnetic features that depend on the structural details and the infiltrating dielectric materials, indicating that the thin, flexible and light 3D printed structures may be used as electromagnetic microwave components and electromagnetic fabrics for coating a variety of devices and infrastructure units, while adapting to different shapes and sizes.

 3D-printed pediatric temporal bone models for surgical training: a patient-specific and low-cost alternative

2019 ◽  
Vol 3 (3) ◽  
pp. 135-143
Author(s):  
Juan C Ospina ◽  
Alejandro Fandiño ◽  
Santiago Hernández ◽  
Luis F Uriza ◽  
Diego Aragonéz ◽  
...  
Keyword(s):  
Temporal Bone ◽  
Surgical Training ◽  
Fused Deposition Modeling ◽  
Surgical Simulation ◽  
Low Cost ◽  
Patient Specific ◽  
Fused Deposition ◽  
Deposition Modeling ◽  
3D Printed ◽  
Temporal Bones

Aim: To determine the usefulness of low-cost 3D-printed pediatric temporal bone models and to define if they could be used as a tool for large-scale surgical training based on their affordability. Materials & methods: Prototypes of a pediatric temporal bone were printed using fused deposition modeling 3D printing technique. The prototypes were drilled. The surgical simulation experience was registered by means of a Likert scale questionnaire. Results: The prototypes adequately simulated a cadaveric temporal bone. The costs associated with production were low compared with other commercial models making it a cost-effective alternative for a temporal bone laboratory. Conclusion: Printed temporal bones created by means of fused deposition modeling are useful for surgical simulation and training in otolaryngology, and it is possible to achieve detailed low-cost models.

The feasibility of printing polylactic acid-nanohydroxyapatite composites using a low-cost fused deposition modeling 3D printer

2016 ◽  
Vol 134 (13) ◽  
Author(s):  
Carola Esposito Corcione ◽  
Francesca Gervaso ◽  
Francesca Scalera ◽  
Francesco Montagna ◽  
Alessandro Sannino ◽  
...  
Keyword(s):  
Polylactic Acid ◽  
Fused Deposition Modeling ◽  
Low Cost ◽  
3D Printer ◽  
Fused Deposition ◽  
Deposition Modeling

scholarly journals Development of Fused Deposition Modeling Using Five-Axis Machine and Printing Methods

2021 ◽  
Author(s):  
Haiguang zhang ◽  
Kunlong zhao ◽  
Di Liu ◽  
Qingxi Hu ◽  
Herfried Lammer
Keyword(s):  
Degrees Of Freedom ◽  
Fused Deposition Modeling ◽  
Low Cost ◽  
Industrial Applications ◽  
3D Printer ◽  
Lightweight Structures ◽  
Fused Deposition ◽  
3D Geometry ◽  
Deposition Modeling ◽  
Five Axis

Abstract Fused deposition modeling (FDM) is one of most widely used 3D printing technologies due to inexpensive equipment and materials, and easy to operate. FDM forms a 3D geometry by slicing a model along the XY-plane and assembling the resulting individual layers along the Z-axis, with extruded thermoplastic filaments. FDM printed parts usually need supporting structures, have stair step effect, and unfavorable mechanical properties. In order to address these deficiencies, a five-axis 3D printer and corresponding printing methods are proposed and developed in this paper. The 3D printer was designed five degrees of freedom through adding a platform that can rotate and swing. Based on the obtained results from different case studies, the discussed machine and methods could become more significant in industrial applications such as low cost, fabricating parts with better surface quality and lightweight structures.

Comparison on Dimensional Accuracy Using a Newly Developed Nozzle for Open-Source 3D Printer

2016 ◽  
Vol 859 ◽  
pp. 15-19 ◽  
Author(s):  
Nor Aiman Sukindar ◽  
Mohd Khairol Anuar Mohd Ariffin ◽  
B.T. Hang Tuah bin Baharudin ◽  
Che Nor Aiza Jaafar ◽  
Mohd Idris Shah Ismail
Keyword(s):  
Open Source ◽  
Fused Deposition Modeling ◽  
Low Cost ◽  
Dimensional Accuracy ◽  
3D Printer ◽  
Constant Heat ◽  
New Era ◽  
Fused Deposition ◽  
Deposition Modeling ◽  
Increasing Demand

Fused Deposition Modeling (FDM) or also known as RepRap (Replicating Rapid Prototyper) is a technology that is synonym with 3D printing. This technology has entered a new era with an increasing demand among the community. It has grown commercially in the market of open-source system and it is relatively low cost. Many efforts have been put towards the development of the system in both hardware and software to increase the quality and the performance. The research highlights the development of a new nozzle to evaluate the performance on dimensional accuracy in comparison to the original nozzle. The nozzle emphasizes the die angle for the polylactic acid (PLA) material, the liquefier design which provide constant heat in the liquefier chamber, as well as insulator for the liquefier using highly insulated material. The dimensional accuracies of both nozzles were compared where the result showed that the new nozzle provided better accuracy and stability on the extruding PLA material.

Biodegradable 3D Printed Polymer Microneedles for Transdermal Drug Delivery

2018 ◽  
Author(s):  
Michael A. Luzuriaga ◽  
Danielle R. Berry ◽  
John C. Reagan ◽  
Ronald A. Smaldone ◽  
Jeremiah J. Gassensmith
Keyword(s):  
Drug Delivery ◽  
3D Printing ◽  
Transdermal Drug Delivery ◽  
Fused Deposition Modeling ◽  
Fused Deposition ◽  
Modeling Software ◽  
Deposition Modeling ◽  
3D Printed ◽  
Microfabrication Technique ◽  
Mechanical Strengths

Biodegradable polymer microneedle (MN) arrays are an emerging class of transdermal drug delivery devices that promise a painless and sanitary alternative to syringes; however, prototyping bespoke needle architectures is expensive and requires production of new master templates. Here, we present a new microfabrication technique for MNs using fused deposition modeling (FDM) 3D printing using polylactic acid, an FDA approved, renewable, biodegradable, thermoplastic material. We show how this natural degradability can be exploited to overcome a key challenge of FDM 3D printing, in particular the low resolution of these printers. We improved the feature size of the printed parts significantly by developing a post fabrication chemical etching protocol, which allowed us to access tip sizes as small as 1 μm. With 3D modeling software, various MN shapes were designed and printed rapidly with custom needle density, length, and shape. Scanning electron microscopy confirmed that our method resulted in needle tip sizes in the range of 1 – 55 µm, which could successfully penetrate and break off into porcine skin. We have also shown that these MNs have comparable mechanical strengths to currently fabricated MNs and we further demonstrated how the swellability of PLA can be exploited to load small molecule drugs and how its degradability in skin can release those small molecules over time.

Sign in / Sign up

Export Citation Format

Share Document