scholarly journals Ga2O3(Sn) Oxides for High-Temperature Gas Sensors

Nanomaterials ◽  
2021 ◽  
Vol 11 (11) ◽  
pp. 2938
Author(s):  
Nataliya Vorobyeva ◽  
Marina Rumyantseva ◽  
Vadim Platonov ◽  
Darya Filatova ◽  
Artem Chizhov ◽  
...  
Keyword(s):  
High Temperature ◽  
Gas Sensors ◽  
Photoelectron Spectroscopy ◽  
Average Crystallite Size ◽  
Nitrogen Adsorption ◽  
Precipitation Method ◽  
X Ray ◽  
Adsorption Sites ◽  
Co Precipitation ◽  
High Temperature Gas

Gallium(III) oxide is a promising functional wide-gap semiconductor for high temperature gas sensors of the resistive type. Doping of Ga2O3 with tin improves material conductivity and leads to the complicated influence on phase content, microstructure, adsorption sites, donor centers and, as a result, gas sensor properties. In this work, Ga2O3 and Ga2O3(Sn) samples with tin content of 0–13 at.% prepared by aqueous co-precipitation method were investigated by X-ray diffraction, nitrogen adsorption isotherms, X-ray photoelectron spectroscopy, infrared spectroscopy and probe molecule techniques. The introduction of tin leads to a decrease in the average crystallite size, increase in the temperature of β-Ga2O3 formation. The sensor responses of all Ga2O3(Sn) samples to CO and NH3 have non-monotonous character depending on Sn content due to the following factors: the formation of donor centers and the change of free electron concentration, increase in reactive chemisorbed oxygen ions concentration, formation of metastable Ga2O3 phases and segregation of SnO2 on the surface of Ga2O3(Sn) grains.

scholarly journals Atomic-Level Dispersion of Bismuth over Co3O4 Nanocrystals—Outstanding Promotional Effect in Catalytic DeN2O

Catalysts ◽  
2020 ◽  
Vol 10 (3) ◽  
pp. 351 ◽  
Author(s):  
Sylwia Wójcik ◽  
Thomas Thersleff ◽  
Klaudia Gębska ◽  
Gabriela Grzybek ◽  
Andrzej Kotarba
Keyword(s):  
Work Function ◽  
Photoelectron Spectroscopy ◽  
N2o Decomposition ◽  
Nitrogen Adsorption ◽  
Atomic Level ◽  
Precipitation Method ◽  
X Ray ◽  
Cobalt Spinel ◽  
Co Precipitation ◽  
Spinel Catalysts

A series of cobalt spinel catalysts doped with bismuth in a broad range of 0–15.4 wt % was prepared by the co-precipitation method. The catalysts were thoroughly characterized by several physicochemical methods (X-ray fluorescence spectroscopy (XRF), X-ray diffraction (XRD), Raman spectroscopy (µRS), X-ray photoelectron spectroscopy (XPS), nitrogen adsorption analyzed with Brunaer-Emmett-Teller theory (N2-BET), work function measurements (WF)), as well as aberration-corrected scanning transmission electron microscopy (STEM) coupled with energy-dispersive X-ray spectroscopy (EDX) and electron energy-loss spectroscopy (EELS). The optimal bismuth promoter content was found to be 6.6 wt %, which remarkably enhanced the performance of the cobalt spinel catalyst, shifting the N2O decomposition (deN2O) temperature window (T50%) down from approximately 400 °C (for Co3O4) to 240 °C (for the 6.6 wt % Bi-Co3O4 catalyst). The high-resolution STEM images revealed that the high activity of the 6.6 wt % Bi-Co3O4 catalyst can be associated with an even, atomic-level dispersion (3.5 at. nm−2) of bismuth over the surface of cobalt spinel nanocrystals. The improvement in catalytic activity was accompanied by an observed increase in the work function. We concluded that Bi promoted mostly the oxygen recombination step of a deN2O reaction, thus demonstrating for the first time the key role of the atomic-level dispersion of a surface promoter in deN2O reactions.

Hydroformylation of Dicyclopentadiene over Rh Catalysts Supported on Fe2O3, Co3O4 and Fe2O3–Co3O4 Mixed Oxide

2017 ◽  
Vol 42 (1) ◽  
pp. 8-13 ◽  
Author(s):  
Yubo Ma ◽  
Zhixian Gao ◽  
Wumanjiang Eli
Keyword(s):  
Mixed Oxide ◽  
Photoelectron Spectroscopy ◽  
Supported Catalyst ◽  
Precipitation Method ◽  
X Ray ◽  
Analysis Techniques ◽  
Rh Catalyst ◽  
Temperature Programmed ◽  
Co Precipitation ◽  
Effect Of The Support

Rh catalysts supported on Fe2O3, Co3O4 and Fe2O3–Co3O4 mixed oxide were prepared by the co-precipitation method. The effect of the support on the performance of the Rh catalysts for the hydroformylation of dicyclopentadiene was investigated using X-ray photoelectron spectroscopy, H2-temperature-programmed reduction, H2-temperature-programmed desorption and Brunauer–Emmett–Teller analysis techniques. The results indicated that the Fe2O3–Co3O4 supported catalyst had a higher dispersion of Rh and thus more Rh+ sites. As a result, the Fe2O3–Co3O4 supported Rh catalyst exhibited higher activity compared with counterparts supported on Fe2O3 and Co3O4.

XRD and Photoluminescence Properties of CaSO4:Dy Phosphor Synthesized by New Co-Precipitation Method

2017 ◽  
Vol 888 ◽  
pp. 333-337 ◽  
Author(s):  
Nadira Kamarudin ◽  
Wan Saffiey Wan Abdullah ◽  
Muhammad Azmi Abdul Hamid
Keyword(s):  
Calcium Sulfate ◽  
Average Crystallite Size ◽  
Information Storage ◽  
Precipitation Method ◽  
Photoluminescence Properties ◽  
Orthorhombic Crystal ◽  
Phosphor Material ◽  
X Ray ◽  
Wide Range ◽  
Co Precipitation

This paper presents the luminescence properties of dysprosium (Dy) doped calcium sulfate (CaSO4) phosphor material produced by co-precipitation technique with 0.1 - 0.5 mol% concentration of dopant. The crystallinity of the produced powder was studied using x-ray powder diffraction (XRD). The XRD spectrum shows high purity anhydrite CaSO4 phosphor material produced. The average crystallite size of 74 nm with orthorhombic crystal system was obtained. The luminescence behavior of produced CaSO4: Dy was studied using a photoluminescence (PL) spectrometer. The excitation and emission spectrum peaks associated with defects and vacancies of the phosphor material at claimed crystalline phase. The mixed peaks of excitation and emission that corresponds to micro and nano sized particle was shown for the produced powders. These properties show that the produced powders have wide range of luminescence detection with many electron traps ready for thermoluminescence (TL) information storage.

scholarly journals Bio-assisted preparation of efficiently architectured nanostructures of γ-Fe2O3 as a molecular recognition platform for simultaneous detection of biomarkers

2020 ◽  
Vol 10 (1) ◽  
Author(s):  
Sasikala Sundar ◽  
V. Ganesh
Keyword(s):  
Electron Microscopy ◽  
Iron Oxide ◽  
Photoelectron Spectroscopy ◽  
Simultaneous Detection ◽  
Differential Pulse ◽  
Precipitation Method ◽  
Limit Values ◽  
X Ray ◽  
Co Precipitation ◽  
The Individual

Abstract Magnetic nanoparticles of iron oxide (γ-Fe2O3) have been prepared using bio-assisted method and their application in the field of biosensors is demonstrated. Particularly in this work, different nanostructures of γ-Fe2O3 namely nanospheres (NS), nanograsses (NG) and nanowires (NW) are prepared using a bio-surfactant namely Furostanol Saponin (FS) present in Fenugreek seeds extract through co-precipitation method by following “green” route. Three distinct morphologies of iron oxide nanostructures possessing the same crystal structure, magnetic properties, and varied size distribution are prepared and characterized. The resultant materials are analyzed using field emission scanning electron microscopy, transmission electron microscopy, powder X-ray diffraction, X-ray photoelectron spectroscopy, vibrating sample magnetometer and Fourier transform infrared spectroscopy. Moreover, the effect of reaction time and concentration of FS on the resultant morphologies of γ-Fe2O3 nanostructures are systematically investigated. Among different shapes, NWs and NSs of γ-Fe2O3 are found to exhibit better sensing behaviour for both the individual and simultaneous electrochemical detection of most popular biomarkers namely dopamine (DA) and uric acid (UA). Electrochemical studies reveal that γ-Fe2O3 NWs showed better sensing characteristics than γ-Fe2O3 NSs and NGs in terms of distinguishable voltammetric signals for DA and UA with enhanced oxidation current values. Differential pulse voltammetric studies exhibit linear dependence on DA and UA concentrations in the range of 0.15–75 µM and 5 μM – 0.15 mM respectively. The detection limit values for DA and UA are determined to be 150 nM and 5 µM. In addition γ-Fe2O3 NWs modified electrode showed higher sensitivity, reduced overpotential along with good selectivity towards the determination of DA and UA even in the presence of other common interferents. Thus the proposed biosensor electrode is very easy to fabricate, eco-friendly, cheaper and possesses higher surface area suggesting the unique structural patterns of γ-Fe2O3 nanostructures to be a promising candidate for electrochemical bio-sensing and biomedical applications.

scholarly journals Effect of Y Modified Ceria Support in Mono and Bimetallic Pd–Au Catalysts for Complete Benzene Oxidation

Catalysts ◽  
2018 ◽  
Vol 8 (7) ◽  
pp. 283 ◽  
Author(s):  
Lyuba Ilieva ◽  
Anna Venezia ◽  
Petya Petrova ◽  
Giuseppe Pantaleo ◽  
Leonarda Liotta ◽  
...  
Keyword(s):  
Photoelectron Spectroscopy ◽  
Catalytic Performance ◽  
Precipitation Method ◽  
Benzene Oxidation ◽  
Total Oxidation ◽  
Pd Catalysts ◽  
X Ray ◽  
Close Relationship ◽  
Ceria Support ◽  
Co Precipitation

Mono metallic and bimetallic Pd (1 wt. %)–Au (3 wt. %) catalysts were prepared using two ceria supports doped with 1 wt. % Y2O3. Yttrium was added by impregnation or co-precipitation. The catalyst synthesis was carried out by deposition–precipitation method, with sequential deposition–precipitation of palladium over previously loaded gold in the case of the bimetallic samples. The obtained materials, characterized by X-ray powder diffraction (XRD), High resolution transmission electron microscopy (HRTEM), X-ray photoelectron spectroscopy (XPS), and temperature programmed reduction (TPR) techniques, were tested in the complete benzene oxidation (CBO). The results of the characterization analyses and the catalytic performance pointed to a close relationship between structural, redox, and catalytic properties of mono and bimetallic catalysts. Among the monometallic systems, Pd catalysts were more active as compared to the corresponding Au catalysts. The bimetallic systems exhibited the best combustion activity. In particular, over Pd–Au supported on Y-impregnated ceria, 100% of benzene conversion towards total oxidation at the temperature of 150 °C was obtained. Comparison of surface sensitive XPS results of fresh and spent catalysts ascertained the redox character of the reaction.

scholarly journals Synthesis of DME by CO2 hydrogenation over La2O3-modified CuO-ZnO-ZrO2/HZSM-5 catalysts

2017 ◽  
Vol 23 (1) ◽  
pp. 49-56 ◽  
Author(s):  
Yajing Zhang ◽  
Yu Zhang ◽  
Fu Ding ◽  
Kangjun Wang ◽  
Wang Xiaolei ◽  
...  
Keyword(s):  
Photoelectron Spectroscopy ◽  
Direct Synthesis ◽  
Catalytic Performance ◽  
Co2 Hydrogenation ◽  
Precipitation Method ◽  
X Ray ◽  
Temperature Programmed ◽  
And Performance ◽  
Co Precipitation ◽  
Adsorption Desorption

A series of La2O3-modified CuO-ZnO-ZrO2/HZSM-5 catalysts were prepared by an oxalate co-precipitation method. The catalysts were fully characterized by X-ray diffraction (XRD), N2 adsorption-desorption, hydrogen temperature pro-grammed reduction (H2-TPR), ammonia temperature programmed desorption (NH3-TPD), and X-ray photoelectron spectroscopy (XPS) techniques. The effect of the La2O3 content on the structure and performance of the catalysts was thoroughly investigated. The catalysts were evaluated for the direct synthesis of dimethyl ether (DME) from CO2 hydrogenation. The results displayed that La2O3 addition enhanced catalytic performance, and the maximal CO2 conversion (34.3%) and DME selectivity (57.3%) were obtained over the catalyst with 1% La2O3, which due to the smaller size of Cu species and a larger ratio of Cu+/Cu.

scholarly journals Synthesis of BaTi5O11 by an aqueous co-precipitation method via stable organic titanate precursor

2021 ◽  
pp. 14-14
Author(s):  
Pelin Aktaş
Keyword(s):  
Aqueous Media ◽  
Average Crystallite Size ◽  
Phase Evolution ◽  
Precipitation Method ◽  
X Ray Diffraction ◽  
Spectroscopy Analysis ◽  
X Ray ◽  
Ft Ir ◽  
Scherrer Formula ◽  
Co Precipitation

BaTi5O11 has been widely researched due to its unique microwave properties. Conventionally it is challenging to obtain this compound as a single phase. The BaTi5O11 was synthesized via co-precipitation technique using an aqueous solution of titanium(IV)(triethanolaminato) isopropoxide, barium nitrate and ammonia as precursors which are stable in an aqueous media. The phase evolution, purity, and structure were identified by X-ray diffraction (XRD), scanning electron microscope (SEM) and energy dispersive X-ray (EDX) spectroscopy analysis. The desired BaTi5O11 structure was obtained by calcination at 900?C. Furthermore, the structure is characterized by TGA, FT-IR and Raman studies. The study showed that the particles were between 80 and 120 nm in size and the average crystallite size was determined from the Scherrer formula as 68.1 nm at 900?C.

Preparation, characterization and dechlorination property of nano Pd-Ni/γ-Al2O3 bimetallic catalyst

2019 ◽  
Vol 12 (06) ◽  
pp. 1951003 ◽  
Author(s):  
Yu Zhang ◽  
Yiyang Wang ◽  
Yalong Liao ◽  
Muyuan Guo ◽  
Gongchu Shi
Keyword(s):  
Photoelectron Spectroscopy ◽  
Inductively Coupled Plasma ◽  
Bimetallic Catalyst ◽  
Average Particle Size ◽  
Nitrogen Adsorption ◽  
Precipitation Method ◽  
Emission Spectrometry ◽  
Average Particle ◽  
Plasma Atomic Emission Spectrometry ◽  
X Ray

Nano Pd-Ni/[Formula: see text]-Al2O3 bimetallic catalyst was prepared by chemical precipitation method enhanced with ultrasonic wave. The influence of dosage of dispersant, ultrasonic intensity and mass ratio of Pd to Ni on the dechlorination property of the catalyst obtained was investigated in detail. The appearance morphology, composition and structure of the catalysts prepared were characterized with X-ray diffraction (XRD), transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS), and nitrogen adsorption, while the specific surface area was determined using the Brunauer–Emmett–Teller (BET) isotherm and the chemical composition of active gradients was tested with inductively coupled plasma-atomic emission spectrometry (ICP-AES). Results indicate that the nano Pd-Ni/[Formula: see text]-Al2O3 bimetallic catalyst prepared has uniform distribution of active ingredients with an average particle size of 4.91[Formula: see text]nm, and the chlorine content of shellac dechlorinated with the catalyst obtained is 0.34[Formula: see text]wt.% which is lower than that reported in the literature, meaning the perfect dechlorination property of the catalyst.

Effect of Noble Metals on Selective Detection of LPG Based on SnO2

1996 ◽  
Vol 459 ◽  
Author(s):  
A. Ratna Phani ◽  
M. Pelino
Keyword(s):  
Photoelectron Spectroscopy ◽  
Noble Metals ◽  
Electrical Response ◽  
Base Material ◽  
High Sensitivity ◽  
Precipitation Method ◽  
X Ray ◽  
Spectroscopy Studies ◽  
Metal Doped ◽  
Co Precipitation

ABSTRACTThe present investigation deals with the electrical response of noble metal doped SnO2 to improve the selectivity for Liquid Petroleum Gas (LPG) in the presence of CO and CH4. Addition of small amounts of nobel metals (Pd, Pt and Rh) to the base material SnO2 is carried out by co-precipitation method. X-ray diffraction and X-ray photoelectron spectroscopy studies are carried out to find out the crystalline phase and chemical composition of the SnO2. The sensor element has been tested for cross selectivity to reducing gases by measuring sensitivity versus sintering temperatures and sensitivity versus operating temperatures. The sensor elements with the composition of Pd (1.5 wt%) andPt (1.5 wt%) in the base material SnO2 sintered at 800°C showed high sensitivity towards LPG at an operating temperature of 350°C suggestingthe possibility to utilize the sensor for the detection of LPG.

A highly active K/Cu-Mn-O catalyst for the removal of nitric oxide in indoor air

2017 ◽  
Vol 28 (1) ◽  
pp. 7-16 ◽  
Author(s):  
Chan Wang ◽  
Feng Li ◽  
Zishu Sun ◽  
Qijun Song
Keyword(s):  
Nitric Oxide ◽  
Indoor Air ◽  
Photoelectron Spectroscopy ◽  
Elimination Rate ◽  
Surface Concentration ◽  
Precipitation Method ◽  
X Ray ◽  
Highly Active ◽  
Metal Nitrates ◽  
Co Precipitation

Nitric oxide is a frequently encountered pollutant in indoor air. It could have a number of harmful effects on human health even at low concentration. Aiming to improve the indoor air quality, an environment-friendly method was developed for the elimination of nitric oxide at ppm level based on a low temperature effective catalyst potassium-doped copper–manganese oxide (K/Cu-Mn-O). The catalyst was obtained through a co-precipitation method using metal nitrates in aqueous solution and the precipitate was calcinated at 400℃ for 5 h. After impregnation with K, the best catalytic activity was observed for the K/Cu-Mn-O catalyst with a Cu/Mn ratio of 1:2 and surface concentration of doping K 7.03% (7.4 mg/g). The composition and the structure of the catalyst were comprehensively characterized by X-ray diffraction, X-ray photoelectron spectroscopy, scanning electron microscopy, and Brunauer–Emmett–Teller. The results showed that the potassium doping improved the adsorption ability of catalyst, and promoted the formation of the nitrate salt, and thereby further improved the elimination rate of nitric oxide. Finally, the possible reaction mechanisms are discussed.

Sign in / Sign up

Export Citation Format

Share Document