scholarly journals Properties of Halide Perovskite Photodetectors with Little Rubidium Incorporation

Nanomaterials ◽  
2022 ◽  
Vol 12 (1) ◽  
pp. 157
Author(s):  
Yuan-Wen Hsiao ◽  
Jyun-You Song ◽  
Hsuan-Ta Wu ◽  
Ching-Chich Leu ◽  
Chuan-Feng Shih
Keyword(s):  
Grain Size ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Absorption Band Edge ◽  
Additional Absorption ◽  
Photovoltaic Properties ◽  
Space Charge Limit ◽  
Photo Response ◽  
Halide Perovskite ◽  
Additional Absorption Band

This study investigates the effects of Rb doping on the Rb-formamidinium-methylammonium-PbI3 based perovskite photodetectors. Rb was incorporated in the perovskite films with different contents, and the corresponding photo-response properties were studied. Doping of few Rb (~2.5%) was found to greatly increase the grain size and the absorbance of the perovskite. However, when the Rb content was greater than 2.5%, clustering of the Rb-rich phases emerged, the band gap decreased, and additional absorption band edge was found. The excess Rb-rich phases were the main cause that degraded the performance of the photodetectors. By space charge limit current analyses, the Rb was found to passivate the defects in the perovskite, lowering the leakage current and reducing the trap densities of carriers. This fact was used to explain the increase in the detectivity. To clarify the effect of Rb, the photovoltaic properties were measured. Similarly, h perovskite with 2.5% Rb doping increased the short-circuit current, revealing the decline of the internal defects. The 2.5% Rb doped photodetector showed the best performance with responsivity of 0.28 AW−1 and ~50% quantum efficiency. Detectivity as high as 4.6 × 1011 Jones was obtained, owing to the improved crystallinity and reduced defects.

Constructing PbS quantum dot sensitized ZnO nanorod array photoelectrodes for highly efficient photovoltaic devices

2016 ◽  
Vol 94 (7) ◽  
pp. 687-692
Author(s):  
Masood Mehrabian ◽  
Naser Ghasemian
Keyword(s):  
Quantum Dot ◽  
Short Circuit ◽  
Zno Nanorods ◽  
Growth Period ◽  
Short Circuit Current ◽  
Nanorod Array ◽  
Open Circuit ◽  
Zno Film ◽  
Photovoltaic Properties ◽  
Pbs Quantum Dot

Solar cells with ZnO film/ZnO nanorods (NRs)/PbS quantum dot (QD) photoelectrodes were constructed and various properties were studied. The ZnO NRs were grown for different periods varying from 0 (ZnO film) to 30 min (ZnO NR30) and the effect of growth period on the photovoltaic properties was investigated. The cell with ZnO film/PbS QD as photoelectrode showed the open circuit voltage VOC of 0.59 V, short circuit current density JSC of 10.06 mAcm−2, and the power conversion efficiency of 3.29% under one sun illumination (air mass 1.5 global illumination at 100 mWcm−2). In a device containing of ZnO film/ZnO NR10/PbS QD (as photoelectrode), mentioned photovoltaic parameters increased to 0.61 V, 10.47 mAcm−2 and 3.81%, respectively.

scholarly journals Direct AFM-based nanoscale mapping and tomography of open-circuit voltages for photovoltaics

2018 ◽  
Vol 9 ◽  
pp. 1802-1808 ◽  
Author(s):  
Katherine Atamanuk ◽  
Justin Luria ◽  
Bryan D Huey
Keyword(s):  
Solar Cells ◽  
Open Circuit Voltage ◽  
Short Circuit ◽  
Photovoltaic Performance ◽  
Three Dimensional ◽  
Short Circuit Current ◽  
Open Circuit ◽  
Photovoltaic Properties ◽  
Order Of Magnitude ◽  
Individual Grains

The nanoscale optoelectronic properties of materials can be especially important for polycrystalline photovoltaics including many sensor and solar cell designs. For thin film solar cells such as CdTe, the open-circuit voltage and short-circuit current are especially critical performance indicators, often varying between and even within individual grains. A new method for directly mapping the open-circuit voltage leverages photo-conducting AFM, along with an additional proportional-integral-derivative feedback loop configured to maintain open-circuit conditions while scanning. Alternating with short-circuit current mapping efficiently provides complementary insight into the highly microstructurally sensitive local and ensemble photovoltaic performance. Furthermore, direct open-circuit voltage mapping is compatible with tomographic AFM, which additionally leverages gradual nanoscale milling by the AFM probe essentially for serial sectioning. The two-dimensional and three-dimensional results for CdTe solar cells during in situ illumination reveal local to mesoscale contributions to PV performance based on the order of magnitude variations in photovoltaic properties with distinct grains, at grain boundaries, and for sub-granular planar defects.

Optical Simulation and Investigation of the Effect of Hysteresis on the Perovskite Solar Cells

NANO ◽  
2019 ◽  
Vol 14 (10) ◽  
pp. 1950127 ◽  
Author(s):  
Farhad Jahantigh ◽  
S. M. Bagher Ghorashi
Keyword(s):  
Grain Size ◽  
Solar Cells ◽  
Open Circuit Voltage ◽  
Short Circuit ◽  
Perovskite Solar Cells ◽  
Short Circuit Current ◽  
Open Circuit ◽  
Hole Transport ◽  
Transport Layer ◽  
Hole Transport Layer

Perovskite solar cells have recently been considered to be an auspicious candidate for the advancement of future photovoltaic research. A power conversion efficiency (PCE) as high as 22% has been reported to be reached, which can be obtained through an inexpensive and high-throughput solution process. Modeling and simulation of these cells can provide deep insights into their fundamental mechanism of performance. In this paper, two different perovskite solar cells are designed by using COMSOL Multiphysics to optimize the thickness of each layer and the overall thickness of the cell. Electric potential, electron and hole concentrations, generation rate, open-circuit voltage, short-circuit current and the output power were calculated. Finally, PCEs of 20.7% and 26.1% were predicted. Afterwards, according to the simulation results, the role of the hole transport layer (HTL) was investigated and the optimum thickness of the perovskite was measured to be 200[Formula: see text]nm for both cells. Therefore, the spin coating settings are selected so that a coating with this thickness for cell 1 is deposited. In order to compare the performance of HTM layer, solar cells with a Spiro-OMeTAD HTM and without the HTM layer in their structure were fabricated. According to the obtained photovoltaic properties, the solar cell made with Spiro-OMeTAD has a more favorable open-circuit voltage ([Formula: see text]), short-circuit current density ([Formula: see text]), fill factor (FF) and PCE compared to the cell without the HTM layer. Also, hysteresis depends strongly on the perovskite grain size, because large average grain size will lead to an increase in the grain’s contact surface area and a decrease in the density of grain boundaries. Finally, according to the results, it was concluded that, in the presence of a hole transport layer, ion transfer was better and ion accumulation was less intense, and therefore, the hysteresis decreases.

Photovoltaic properties of silicon nanocrystals in silicon nitride prepared by ammonia sputtering

2015 ◽  
Vol 08 (05) ◽  
pp. 1550052
Author(s):  
Xiaobo Chen
Keyword(s):  
Silicon Nitride ◽  
Flow Rate ◽  
Photoelectron Spectroscopy ◽  
Silicon Nanocrystals ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Open Circuit ◽  
Photovoltaic Properties ◽  
X Ray ◽  
Xps Characterization

In this work, we present an investigation of the photovoltaic properties of low-temperature (700°C annealing temperature) prepared P -doped Silicon nanocrystals ( Si   NCs ) in silicon nitride by ammonia sputtering followed by rapid thermal annealing (RTA). We examined how the flow rate of NH3influenced the structural properties of the annealed films by using Raman scattering, grazing incidence X-ray diffraction (GI XRD) and transmission electron microscopy (TEM), it was found that the appropriate flow rate of NH3is 3 sccm. For the sample deposited at the flow rate of 3 sccm, TEM image showed that Si   NCs were formed with a mean size about 3.7 nm and the density of ~ 2.1 × 1012cm-2; X-ray photoelectron spectroscopy (XPS) characterization showed the existence of Si – P bonds, indicating effective P doping; the average absorptance of higher than 65% and a significant amount of photocurrent makes it suitable for photoactive. Moreover, the experimental P -doped Si   NCs : Si3N4/ p - Si heterojunction solar cell has been fabricated, and the device performance was studied. The photovoltaic device fabricated exhibits an open-circuit voltage (VOC) and a short-circuit current density (JSC) of 470 mV and 3.25 mA/cm2, respectively.

Influence of Silicon Texturization on the Photovoltaic Properties of CuPc/n-Si Hybrid Solar Cells

2012 ◽  
Vol 531-532 ◽  
pp. 40-44
Author(s):  
Zhi Feng Liu ◽  
Yi Ting Liu
Keyword(s):  
Solar Cell ◽  
Current Density ◽  
Copper Phthalocyanine ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Energy Conversion Efficiency ◽  
Short Circuit Current Density ◽  
Hybrid Solar Cell ◽  
Photovoltaic Properties ◽  
Current Voltage

Hybrid solar cell based on copper-phthalocyanine (CuPc) and textured Si has been fabricated. Influence of silicon texturization on the photovoltaic properties of CuPc/n-Si hybrid solar cell was studied by current-voltage characteristic curves in the dark and under illumination conditions. As a result, it is found that textured Si can improve significantly the performance of hybrid solar cell. It exhibits a three times increase in the short-circuit current density with respect to that of the standard hybrid solar cell, and the short-circuit current density reaches up to 5.4 mA/cm2. In addition, the open-voltage and fill factor are almost constant. The solar-energy conversion efficiency is increased by about three times by the textured Si and achieved about 0.8% under “one Sun” illumination. Furthermore, the possible reasons for this result have been discussed.

Novel Linear and Hyperbranched Polythiophene Derivatives Containing Diketopyrrolopyrroles as Linking Groups

2015 ◽  
Vol 1771 ◽  
pp. 213-219
Author(s):  
Sheng-Hsiung Yang ◽  
Chia-Hao Hsieh
Keyword(s):  
Fill Factor ◽  
Open Circuit Voltage ◽  
Short Circuit ◽  
Power Conversion ◽  
Short Circuit Current ◽  
Open Circuit ◽  
Photovoltaic Properties ◽  
Molecular Weights ◽  
Active Layers ◽  
Film State

ABSTRACTThe goal of this research is to synthesize novel linear and hyperbranched polythiophene derivatives containing diketopyrrolopyrrole (DPP) as linking groups, and to investigate thermal, optical, electrochemical, and photovoltaic properties of those derivatives. Polymers with high regioregularity were synthesized via the Universal Grignard metathesis polymerization. Those linear or hyperbranched polythiophenes containing DPP bridging moieties showed higher molecular weights and better thermal stability compared with normal P3HT. The UV-vis absorption spectra of the DPP-containing polymers are similar to that of P3HT in film state, while they show distinct attenuation in fluorescent emission. Finally, all polymers were blended with PC61BM and used as active layers for fabrication of inverted solar devices. The devices based on those DPP-containing polythiophenes revealed the open-circuit voltage (VOC) of 0.55–0.58 V, the short-circuit current (JSC) of 8.62–16.21 mA/cm2, the fill factor (FF) of 36–41%, and the power conversion efficiency (PCE) of 1.73–3.74%.

scholarly journals Synthesis of Cyano-Substituted Conjugated Polymers for Photovoltaic Applications

Polymers ◽  
2019 ◽  
Vol 11 (5) ◽  
pp. 746 ◽  
Author(s):  
Mun Ho Yang ◽  
Ho Cheol Jin ◽  
Joo Hyun Kim ◽  
Dong Wook Chang
Keyword(s):  
Conjugated Polymers ◽  
Molecular Orbital ◽  
Polymer Solar Cells ◽  
Short Circuit ◽  
Energy Levels ◽  
Coupling Reaction ◽  
Short Circuit Current ◽  
Open Circuit ◽  
Strong Electron ◽  
Photovoltaic Properties

Three conjugated polymers, in which the electron-donating (D) 5-alkylthiophene-2-yl-substitued benzodithiophene was linked to three different electron-accepting (A) moieties, i.e., benzothiadiazole (BT), diphenylquinoxaline (DPQ), and dibenzophenazine (DBP) derivative via thiophene bridge, were synthesized using the Stille coupling reaction. In particular, the strong electron-withdrawing cyano (CN) group was incorporated into the A units BT, DPQ, and DBP to afford three D–A type target polymers PB–BTCN, PB–DPQCN, and PB–DBPCN, respectively. Owing to the significant contribution of the CN-substituent, these polymers exhibit not only low-lying energy levels of both the highest occupied molecular orbital and the lowest unoccupied molecular orbital, but also reduced bandgaps. Furthermore, to investigate the photovoltaic properties of polymers, inverted-type devices with the structure of ITO/ZnO/Polymer:PC71BM/MoO3/Ag were fabricated and analyzed. All the polymer solar cells based on the three cyano-substituted conjugated polymers showed high open-circuit voltages (Voc) greater than 0.89 V, and the highest power conversion efficiency of 4.59% was obtained from the device based on PB-BtCN with a Voc of 0.93 V, short-circuit current of 7.36 mA cm−2, and fill factor of 67.1%.

scholarly journals Steady Enhancement in Photovoltaic Properties of Fluorine Functionalized Quinoxaline-Based Narrow Bandgap Polymer

Molecules ◽  
2018 ◽  
Vol 24 (1) ◽  
pp. 54 ◽  
Author(s):  
Zhonglian Wu ◽  
Huanxiang Jiang ◽  
Xingzhu Wang ◽  
Lei Yan ◽  
Wei Zeng ◽  
...  
Keyword(s):  
Fill Factor ◽  
Polymer Solar Cells ◽  
Short Circuit ◽  
Photovoltaic Performance ◽  
Hole Mobility ◽  
Short Circuit Current ◽  
Open Circuit ◽  
Promising Candidate ◽  
Photovoltaic Properties ◽  
Narrow Bandgap

To investigate the influence of fluoride phenyl side-chains onto a quinoxaline (Qx) unit on the photovoltaic performance of the narrow bandgap (NBG) photovoltaic polymers, herein, two novel NBG copolymers, PBDTT-DTQx and PBDTT-DTmFQx, were synthesized and characterized. 2-ethylhexylthiothiophene-substituted benzodithiophene (BDTT), 2,3-diphenylquinoxaline (DQx) [or 2,3-bis(3-fluorophenyl)quinoxaline (DmFQx)] and 2-ethylhexylthiophene (T) were used as the electron donor (D) unit, electron-withdrawing acceptor (A) unit and π-bridge, respectively. Compared to non-fluorine substituted PBDTT-DTQx, fluoride PBDTT-DTmFQx exhibited a wide UV-Vis absorption spectrum and high hole mobility. An enhanced short-circuit current (Jsc) and fill factor (FF) simultaneously gave rise to favorable efficiencies in the polymer/PC71BM-based polymer solar cells (PSCs). Under the illumination of AM 1.5G (100 mW cm−2), a maximum power conversion efficiency (PCE) of 6.40% was achieved with an open-circuit voltage (Voc) of 0.87 V, a Jsc of 12.0 mA cm−2 and a FF of 61.45% in PBDTT-DTmFQx/PC71BM-based PSCs, while PBDTT-DTQx-based devices also exhibited a PCE of 5.43%. The excellent results obtained demonstrate that PBDTT-DTmFQx by fluorine atom engineering could be a promising candidate for organic photovoltaics.

scholarly journals Fabrication and Characterization of CH3NH3PbI3 Perovskite Solar Cells Added with Polysilanes

2018 ◽  
Vol 2018 ◽  
pp. 1-7 ◽  
Author(s):  
Takeo Oku ◽  
Junya Nomura ◽  
Atsushi Suzuki ◽  
Hiroki Tanaka ◽  
Sakiko Fukunishi ◽  
...  
Keyword(s):  
Solar Cells ◽  
Short Circuit ◽  
Perovskite Solar Cells ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Open Circuit ◽  
Interfacial Structure ◽  
Perovskite Layer ◽  
Photovoltaic Properties ◽  
Coating Method

Effects of polysilane additions on CH3NH3PbI3 perovskite solar cells were investigated. Photovoltaic cells were fabricated by a spin-coating method using perovskite precursor solutions with polymethyl phenylsilane, polyphenylsilane, or decaphenyl cyclopentasilane (DPPS), and the microstructures were examined by X-ray diffraction and optical microscopy. Open-circuit voltages were increased by introducing these polysilanes, and short-circuit current density was increased by the DPPS addition, which resulted in the improvement of the photoconversion efficiencies to 10.46%. The incident photon-to-current conversion efficiencies were also increased in the range of 400~750 nm. Microstructure analysis indicated the formation of a dense interfacial structure by grain growth and increase of surface coverage of the perovskite layer with DPPS, and the formation of PbI2 was suppressed, leading to the improvement of photovoltaic properties.

Preparation and Photovoltaic Properties of Flexible Dye-Sensitized Solar Cells

2011 ◽  
Vol 306-307 ◽  
pp. 112-115 ◽  
Author(s):  
You Zeng ◽  
Li Jia Zhao ◽  
Ying Zhen ◽  
Fang Xiao Shi ◽  
Yu Tong
Keyword(s):  
Solar Cells ◽  
Short Circuit ◽  
Dye Sensitized Solar Cells ◽  
Short Circuit Current ◽  
Open Circuit ◽  
Treatment Temperature ◽  
Photovoltaic Properties ◽  
Dye Sensitized ◽  
Conductive Glass ◽  
Sensitized Solar Cells

Flexible dye-sensitized solar cells (DSCs) were prepared by using carbon nanotube transparent conductive films (CNT-TCFs) as flexible substrates, and their photovoltaic properties were investigated as well. The flexible DSCs show typical photovoltaic characteristics with short-circuit current of 0.78 μA and open-circuit voltage of 1.48 mV, which was strongly influenced by heat-treatment temperature, type of dyes, and electrical resistivity. In light of their lighter weight and higher flexibility than conventional DSCs based on conductive glass substrates, the flexible DSCs have great potential as functional photoelectric components in many fields.

Sign in / Sign up

Export Citation Format

Share Document