scholarly journals Investigation of the Mechanical Properties of Parts Fabricated with Ultrasonic Micro Injection Molding Process Using Polypropylene Recycled Material

Polymers ◽  
2020 ◽  
Vol 12 (9) ◽  
pp. 2033
Author(s):  
Rafael Gaxiola-Cockburn ◽  
Oscar Martínez-Romero ◽  
Alex Elías-Zúñiga ◽  
Daniel Olvera-Trejo ◽  
José Emiliano Reséndiz-Hernández ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Injection Molding ◽  
Uniaxial Extension ◽  
Physical And Mechanical Properties ◽  
Injection Molding Process ◽  
Slight Reduction ◽  
Molding Process ◽  
Scanning Calorimetry ◽  
Micro Injection Molding ◽  
Recycled Material

This research focuses on investigating how physical and mechanical properties of polypropylene (PP) recycled material are modified when ultrasonic micro injection molding (UMIM) technology is used to produce material specimens. Experimental characterization by differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), Fourier transform infrared (FTIR) spectra, and rheology tests show that the fabricated PP samples were able to withstand up to five times recycled processing before some signs of mechanical and physical properties degradation are observed. Surprisingly, uniaxial extension tests show an increase of 3.07%, 10.97% and 27.33% for Young’s modulus, yield stress and ultimate stress values, respectively, and a slight reduction of 1.29% for the samples elongation at break when compared to the experimental data collected from virgin material samples. The improvement of these mechanical properties in the recycled samples suggests that ultrasonic microinjection produces a mechano-chemical material change.

scholarly journals Vacuum Venting Enhances the Replication of Nano/Microfeatures in Micro-Injection Molding Process

2016 ◽  
Vol 4 (2) ◽  
Author(s):  
Seong Ying Choi ◽  
Nan Zhang ◽  
J. P. Toner ◽  
G. Dunne ◽  
Michael D. Gilchrist
Keyword(s):  
Injection Molding ◽  
Quantitative Study ◽  
Vacuum Pressure ◽  
Injection Molding Process ◽  
Anodized Aluminum ◽  
Molding Process ◽  
Micro Injection Molding ◽  
Sample Shape ◽  
Final Sample ◽  
Qualitative And Quantitative Study

Vacuum venting is a method proposed to improve feature replication in microparts that are fabricated using micro-injection molding (MIM). A qualitative and quantitative study has been carried out to investigate the effect of vacuum venting on the nano/microfeature replication in MIM. Anodized aluminum oxide (AAO) containing nanofeatures and a bulk metallic glass (BMG) tool mold containing microfeatures were used as mold inserts. The effect of vacuum pressure at constant vacuum time, and of vacuum time at constant vacuum pressure on the replication of these features is investigated. It is found that vacuum venting qualitatively enhances the nanoscale feature definition as well as increases the area of feature replication. In the quantitative study, higher aspect ratio (AR) features can be replicated more effectively using vacuum venting. Increasing both vacuum pressure and vacuum time are found to improve the depth of replication, with the vacuum pressure having more influence. Feature orientation and final sample shape could affect the absolute depth of replication of a particular feature within the sample.

The Effect of Heat Treatment on Mechanical Properties of Car Interior Fabric Used for Injection Molding

2012 ◽  
Vol 532-533 ◽  
pp. 234-237
Author(s):  
Wei Lai Chen ◽  
Ding Hong Yi ◽  
Jian Fu Zhang
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
High Temperature ◽  
Injection Molding ◽  
High Temperatures ◽  
Material Properties ◽  
Injection Molding Process ◽  
Molding Process ◽  
Composite Fabrics

The purpose of this paper is to study the effect of high temperature in injection molding process on mechanical properties of the warp-knitted and nonwoven composite fabrics (WNC)used in car interior. Tensile, tearing and peeling properties of WNC fabrics were tested after heat treatment under120, 140,160,180°C respectively. It was found that, after 140°C heat treatment, the breaking and tearing value of these WNC fabrics are lower than others. The results of this study show that this phenomenon is due to the material properties of fabrics. These high temperatures have no much effect on peeling properties of these WNC fabrics. It is concluded that in order to preserve the mechanical properties of these WNC fabrics, the temperature near 140°C should be avoided possibly during injection molding process.

Tribology study of hydroxyapatite (HAp) scaffold blended single based binder via rheology and mechanical properties

2017 ◽  
Vol 69 (3) ◽  
pp. 414-419
Author(s):  
Mimi Azlina Abu Bakar ◽  
Siti Norazlini Abd Aziz ◽  
Muhammad Hussain Ismail
Keyword(s):  
Mechanical Properties ◽  
Injection Molding ◽  
Palm Stearin ◽  
Polymeric Materials ◽  
High Energy ◽  
Single Step ◽  
Injection Molding Process ◽  
Plastic Behavior ◽  
Molding Process ◽  
Content Type

Purpose This paper aims to investigate the vital characteristic of an innovative ceramic injection molding (CIM) process for orthopedic application with controlled porosity and improved tribological and mechanical properties which were affected by complex tribological interactions, whether lubricated like hip implants and other artificial prostheses. The main objective is to maximize the usage of palm stearin as a single based binder as the function of flow properties during injection molding process. Design/methodology/approach The binder used in this present study consists of 100 per cent palm stearin manufactured by Kempas Oil Sdn Bhd and supplied by Vistec Technology Sdn Bhd. The feedstock was prepared by using a Z-blade mixer (Thermo Haake Rheomix OS) and Brabender mixer model R2400. The feedstock prepared was injection molded using a manually operated vertical benchtop machine with an average pressure of about 5-7 bars. The firing step included the temporary holds at intermediate temperatures to burn out organic binders. At this stage, the green molded specimen was de-bound using a single-step wick-debinding method. Findings The maximum content of ceramic material is applied to investigate the efficiencies of net formulation that can be achieved by ceramic materials. The longer the viscosity will change with shear rate, the higher the value of n obtained instead. From the slope of the curves obtained in Figure 3, the value of n for the feedstock was determined to be less than 1, which indicates a pseudoplastic behavior and suitability for the molding process. Moreover, high shear sensitivity is important in producing complex and intrinsic specimens which are leading products in the CIM industry. Originality/value The feedstock containing HAp powder and palm stearin binder was successfully prepared at very low temperature of 70°C, which promoting a required pseudo-plastic behavior during rheological test. The single binder palm stearin should be optimized in other research works carried out, as palm stearin is most preferred compared to other polymeric materials that provided high energy consumption when subjected to the sintering process. Besides the binder is widely available in Malaysia, low cost and harmless effect during debinding process.

Manufacturing and High Temperature Mechanical Properties of Inconel 713C by Using Metal Injection Molding

2012 ◽  
Vol 602-604 ◽  
pp. 627-630 ◽  
Author(s):  
Kyu Sik Kim ◽  
Kee Ahn Lee ◽  
Jong Ha Kim ◽  
Si Woo Park ◽  
Kyu Sang Cho
Keyword(s):  
Mechanical Properties ◽  
High Temperature ◽  
Injection Molding ◽  
Room Temperature ◽  
Tensile Tests ◽  
Metal Injection Molding ◽  
Injection Molding Process ◽  
Molding Process ◽  
High Temperature Mechanical Properties ◽  
Inconel 713C

Inconel 713C alloy was tried to manufacture by using MIM(Metal Injection Molding) process. The high-temperature mechanical properties of MIMed Inconel 713C were also investigated. Processing defects such as pores and binders could be observed near the surface. Tensile tests were conducted from room temperature to 900°C. The result of tensile tests showed that this alloy had similar or somewhat higher strengths (YS: 734 MPa, UTS: 968 MPa, elongation: 7.16 % at room temperature) from RT to 700°C than those of conventional Inconel 713C alloys. Above 800°C, however, ultimate tensile strength decreased rapidly with increasing temperature (lower than casted Inconel 713C). Based on the observation of fractography, initial crack was found to have started near the surface defects and propagated rapidly. The superior mechanical properties of MIMed Inconel 713C could be obtained by optimizing the MIM process parameters.

Powder Injection Molding of Ti-6Al-4V Alloy for Defect-Free High Performance Titanium Parts with Low Carbon/Oxygen Contents

2018 ◽  
Vol 770 ◽  
pp. 189-194
Author(s):  
Dong Guo Lin ◽  
Jae Man Park ◽  
Tae Gon Kang ◽  
Seong Taek Chung ◽  
Young Sam Kwon ◽  
...  
Keyword(s):  
Injection Molding ◽  
Alloy Powder ◽  
High Performance ◽  
Physical And Mechanical Properties ◽  
Powder Injection Molding ◽  
Powder Injection ◽  
Solid Loading ◽  
Injection Molding Process ◽  
Low Carbon ◽  
Molding Process

In this work, powder injection molding (PIM) of Ti-6Al-4V alloy powder has been studied. Defect-free high performance Ti-6Al-4V parts with low carbon/oxygen contents have been successfully prepared by PIM. A pre-alloyed Ti-6Al-4V alloy powder and wax-polymer binder system have been mixed together to prepare the feedstock. In mixing stage, the solid loading percentage and mixing conditions have been optimized. Rheological and thermal debinding behaviors of prepared feedstock have been characterized and numerically expressed based on rheometry and thermal gravity experimental results. In addition, the injection molding process of Ti-6Al-4V parts has been numerically analyzed to optimize the injection molding conditions. Consequently, the defect-free Ti-6Al-4V parts with low carbon and oxygen contents have been successfully fabricated by PIM, which exhibits excellent physical and mechanical properties.

Process comparison on the microstructure and mechanical properties of fiber-reinforced polyphenylene sulfide using MuCell technology

2018 ◽  
Vol 37 (15) ◽  
pp. 1020-1034 ◽  
Author(s):  
Christoph Lohr ◽  
Björn Beck ◽  
Frank Henning ◽  
Kay André Weidenmann ◽  
Peter Elsner
Keyword(s):  
Mechanical Properties ◽  
High Pressure ◽  
Injection Molding ◽  
Fiber Orientation ◽  
Polyphenylene Sulfide ◽  
Injection Molding Process ◽  
Fiber Reinforced ◽  
Molding Process ◽  
Glass Fiber Reinforced ◽  
Foam Injection Molding

The MuCell process is a special injection molding process which utilizes supercritical gas (nitrogen) to create integral foam sandwiches. The advantages are lower weight, higher specific properties and shorter cycle times. In this study, a series of glass fiber-reinforced polyphenylene sulfide foam blanks are manufactured using the MuCell injection molding process. The different variations of the process (low-pressure also known as structural foam injection molding) and high-pressure foam injection molding (also known as “core back expansion,” “breathing mold,” “precision opening,” decompression molding) are used. The sandwich structure and mechanical properties (tensile strength, bending strength, and impact behavior) of the microcellular and glass fiber-reinforced polyphenylene sulfide foams are systematically investigated and compared to compact material. The results showed that the injection parameters (injection speed, foaming mechanism) played an important role in the relative density of microcellular polyphenylene sulfide foams and the mechanical properties. It could be shown that the specific tensile strength decreased while increasing the degree of foaming which can be explained by the increased number of cells and the resulting cell size. This leads to stress peaks which lower the mechanical properties. The Charpy impact strength shows a significant dependence on the fiber orientation. The specific bending modulus of the high-pressure foaming process, however, surpasses the values of the other two processes showing the potential of this manufacturing variation especially with regard to bending loads. Furthermore, a high dependence of the mechanical properties on the fiber orientation of the tested specimens can be found.

scholarly journals Experimental Validation of Injection Molding Simulations of 3D Microparts and Microstructured Components Using Virtual Design of Experiments and Multi-Scale Modeling

Micromachines ◽  
2020 ◽  
Vol 11 (6) ◽  
pp. 614 ◽  
Author(s):  
Dario Loaldi ◽  
Francesco Regi ◽  
Federico Baruffi ◽  
Matteo Calaon ◽  
Danilo Quagliotti ◽  
...  
Keyword(s):  
Injection Molding ◽  
Process Simulation ◽  
Current Work ◽  
Injection Molding Process ◽  
Process Conditions ◽  
Virtual Design ◽  
Molding Process ◽  
Micro Injection Molding ◽  
Multi Scale ◽  
Filling Time

The increasing demand for micro-injection molding process technology and the corresponding micro-molded products have materialized in the need for models and simulation capabilities for the establishment of a digital twin of the manufacturing process. The opportunities enabled by the correct process simulation include the possibility of forecasting the part quality and finding optimal process conditions for a given product. The present work displays further use of micro-injection molding process simulation for the prediction of feature dimensions and its optimization and microfeature replication behavior due to geometrical boundary effects. The current work focused on the micro-injection molding of three-dimensional microparts and of single components featuring microstructures. First, two virtual a studies were performed to predict the outer diameter of a micro-ring within an accuracy of 10 µm and the flash formation on a micro-component with mass a 0.1 mg. In the second part of the study, the influence of microstructure orientation on the filling time of a microcavity design section was investigated for a component featuring micro grooves with a 15 µm nominal height. Multiscale meshing was employed to model the replication of microfeatures in a range of 17–346 µm in a Fresnel lens product, allowing the prediction of the replication behavior of a microfeature at 91% accuracy. The simulations were performed using 3D modeling and generalized Navier–Stokes equations using a single multi-scale simulation approach. The current work shows the current potential and limitations in the use of micro-injection molding process simulations for the optimization of micro 3D-part and microstructured components.

Sign in / Sign up

Export Citation Format

Share Document