scholarly journals Fabrication and Thermoelectric Characterization of Transition Metal Silicide-Based Composite Thermocouples

Sensors ◽  
2018 ◽  
Vol 18 (11) ◽  
pp. 3759 ◽  
Author(s):  
Gunes Yakaboylu ◽  
Rajalekshmi Pillai ◽  
Katarzyna Sabolsky ◽  
Edward Sabolsky
Keyword(s):  
High Temperature ◽  
High Sensitivity ◽  
Temperature Gradients ◽  
Metal Silicide ◽  
X Ray Diffraction ◽  
Seebeck Coefficients ◽  
Thermoelectric Voltage ◽  
Sensing Applications ◽  
Significant Difference ◽  
Cold Junction

Metal silicide-based thermocouples were fabricated by screen printing thick films of the powder compositions onto alumina tapes followed by lamination and sintering processes. The legs of the embedded thermocouples were composed of composite compositions consisting of MoSi2, WSi2, ZrSi2, or TaSi2 with an additional 10 vol % Al2O3 to form a silicide–oxide composite. The structural and high-temperature thermoelectric properties of the composite thermocouples were examined using X-ray diffraction, scanning electron microscopy and a typical hot–cold junction measurement technique. MoSi2-Al2O3 and WSi2-Al2O3 composites exhibited higher intrinsic Seebeck coefficients (22.2–30.0 µV/K) at high-temperature gradients, which were calculated from the thermoelectric data of composite//Pt thermocouples. The composite thermocouples generated a thermoelectric voltage up to 16.0 mV at high-temperature gradients. The MoSi2-Al2O3//TaSi2-Al2O3 thermocouple displayed a better performance at high temperatures. The Seebeck coefficients of composite thermocouples were found to range between 20.9 and 73.0 µV/K at a temperature gradient of 1000 °C. There was a significant difference between the calculated and measured Seebeck coefficients of these thermocouples, which indicated the significant influence of secondary silicide phases (e.g., Mo5Si3, Ta5Si3) and possible local compositional changes on the overall thermoelectric response. The thermoelectric performance, high sensitivity, and cost efficiency of metal silicide–alumina ceramic composite thermocouples showed promise for high-temperature and harsh-environment sensing applications.

scholarly journals High-temperature X-ray scattering studies of atomic layer deposited IrO2

2020 ◽  
Vol 53 (2) ◽  
pp. 369-380
Author(s):  
Mikko J. Heikkilä ◽  
Jani Hämäläinen ◽  
Esa Puukilainen ◽  
Markku Leskelä ◽  
Mikko Ritala
Keyword(s):  
High Temperature ◽  
Phase Change ◽  
High Sensitivity ◽  
Atomic Layer ◽  
Ex Situ ◽  
X Ray Diffraction ◽  
X Ray ◽  
Force Microscopy ◽  
Atomic Force ◽  
Change Temperature

IrO2 is an important material in numerous applications ranging from catalysis to the microelectronics industry, but despite this its behaviour upon annealing under different conditions has not yet been thoroughly studied. This work provides a detailed investigation of the annealing of IrO2 thin films using in situ high-temperature X-ray diffraction and X-ray reflectivity (HTXRR) measurements from room temperature up to 1000°C in oxygen, nitrogen, forming gas and vacuum. Complementary ex situ scanning electron microscopy and atomic force microscopy measurements were conducted. The combined data show the dependencies of crystalline properties and surface morphology on the annealing temperature and atmosphere. The reduction of IrO2 to Ir takes place at a temperature as low as 150°C in forming gas, but in oxygen IrO2 is stable up to 800°C and evaporates as a volatile oxide at higher temperatures. The IrO2 crystallite size remains constant in oxygen up to 400°C and increases above that, while in the more reducing atmospheres the Ir crystallites grow continuously above the phase-change temperature. The role of HTXRR in the analysis is shown to be important since its high sensitivity allows one to observe changes taking place in the film at temperatures much below the phase change.

The Enhanced Thermoelectric Properties of Ba0.4Co4Sb11.7Te0.3 Prepared by the High-Pressure and High-Temperature Method

2014 ◽  
Vol 33 (1) ◽  
pp. 59-63
Author(s):  
Song Hao ◽  
Hong An Ma ◽  
Le Deng ◽  
Kai Kai Jie ◽  
Zhe Liu ◽  
...  
Keyword(s):  
High Pressure ◽  
High Temperature ◽  
Thermoelectric Properties ◽  
Figure Of Merit ◽  
Thermoelectric Figure Of Merit ◽  
X Ray Diffraction ◽  
Thermoelectric Figure ◽  
Seebeck Coefficients ◽  
Temperature Method ◽  
Increasing Temperature

AbstractPolycrystalline skutterudite Ba0.4Co4Sb11.7Te0.3 with a bcc crystal structure was prepared by the High-Pressure and High-Temperature (HPHT) method. The study explored a chemical method for introducing Ba atoms into the voids of CoSb3 to optimize the thermoelectric figure of merit ZT in the system of Ba0.4Co4Sb11.7Te0.3. The samples were characterized by X-ray diffraction, electron microprobe analysis, and thermoelectric properties measurement. The electrical resistivity, Seebeck coefficients and thermal conductivities of the samples were measured in the temperature range of 300–743 K. The power factor and the figure of merit, ZT, of the samples all increased with the increasing temperature. A dimensionless thermoelectric figure of merit of 0.87 at 743 K was achieved for n-type Ba0.4Co4Sb11.7Te0.3 at last. The results indicated Ba-filled CoSb3 prepared by HPHT method is an effective method to greatly enhance the thermoelectric properties of skutterudite compounds.

High temperature X-ray diffraction investigation of an aluminium-silicon-corundum system

2007 ◽  
Vol 2007 (suppl_26) ◽  
pp. 369-374 ◽  
Author(s):  
D. Garipoli ◽  
P. Bergese ◽  
E. Bontempi ◽  
M. Minicucci ◽  
A. Di Cicco ◽  
...  
Keyword(s):  
High Temperature ◽  
X Ray Diffraction ◽  
X Ray

Low Molecular Weight Microfibers with Light Sensing Properties

2017 ◽  
Vol 54 (4) ◽  
pp. 655-658
Author(s):  
Andrei Bejan ◽  
Dragos Peptanariu ◽  
Bogdan Chiricuta ◽  
Elena Bicu ◽  
Dalila Belei
Keyword(s):  
Molecular Weight ◽  
Low Molecular Weight ◽  
X Ray Diffraction ◽  
Aromatic Rings ◽  
X Ray ◽  
Force Microscopy ◽  
Light Sensing ◽  
Sensing Applications ◽  
Atomic Force ◽  
Low Molecular Weight Compounds

Microfibers were obtained from organic low molecular weight compounds based on heteroaromatic and aromatic rings connected by aliphatic spacers. The obtaining of microfibers was proved by scanning electron microscopy. The deciphering of the mechanism of microfiber formation has been elucidated by X-ray diffraction, infrared spectroscopy, and atomic force microscopy measurements. By exciting with light of different wavelength, florescence microscopy revealed a specific optical response, recommending these materials for light sensing applications.

scholarly journals High-pressure synthesis and crystal structure of the mixed-cation borate Ga4In4B15O33(OH)3

2019 ◽  
Vol 74 (4) ◽  
pp. 357-363
Author(s):  
Daniela Vitzthum ◽  
Hubert Huppertz
Keyword(s):  
Crystal Structure ◽  
High Pressure ◽  
High Temperature ◽  
Diffraction Data ◽  
X Ray Diffraction ◽  
Synthesis And Crystal Structure ◽  
X Ray ◽  
Mixed Cation ◽  
High Pressure High Temperature ◽  
Pressure Synthesis

AbstractThe mixed cation triel borate Ga4In4B15O33(OH)3 was synthesized in a Walker-type multianvil apparatus at high-pressure/high-temperature conditions of 12.5 GPa and 1300°C. Although the product could not be reproduced in further experiments, its crystal structure could be reliably determined via single-crystal X-ray diffraction data. Ga4In4B15O33(OH)3 crystallizes in the tetragonal space group I41/a (origin choice 2) with the lattice parameters a = 11.382(2), c = 15.244(2) Å, and V = 1974.9(4) Å3. The structure of the quaternary triel borate consists of a complex network of BO4 tetrahedra, edge-sharing InO6 octahedra in dinuclear units, and very dense edge-sharing GaO6 octahedra in tetranuclear units.

The Application of X-Ray Diffraction at Elevated Temperatures to Study the Mechanism of Formation of Sodium Tripolyphosphate

1961 ◽  
Vol 5 ◽  
pp. 276-284
Author(s):  
E. L. Moore ◽  
J. S. Metcalf
Keyword(s):  
High Temperature ◽  
Low Temperature ◽  
Amorphous Phase ◽  
Elevated Temperatures ◽  
Sodium Tripolyphosphate ◽  
X Ray Diffraction ◽  
Mechanism Of Formation ◽  
X Ray ◽  
Temperature Form ◽  
High Temperature Form

AbstractHigh-temperature X-ray diffraction techniques were employed to study the condensation reactions which occur when sodium orthophosphates are heated to 380°C. Crystalline Na4P2O7 and an amorphous phase were formed first from an equimolar mixture of Na2HPO4·NaH2PO4 and Na2HPO4 at temperatures above 150°C. Further heating resulted in the formation of Na5P3O10-I (high-temperature form) at the expense of the crystalline Na4P4O7 and amorphous phase. Crystalline Na5P3O10-II (low-temperature form) appears after Na5P3O10-I.Conditions which affect the yield of crystalline Na4P2O7 and amorphous phase as intermediates and their effect on the yield of Na5P3O10 are also presented.

Mechanical Alloying Behavior in the Nb-Si, Ta-Si, and Nb-Ta-Si Systems

1988 ◽  
Vol 133 ◽  
Author(s):  
K. S. Kumar ◽  
S. K. Mannan
Keyword(s):  
High Temperature ◽  
Mechanical Alloying ◽  
Mechanical Milling ◽  
Room Temperature ◽  
Crystalline Compound ◽  
X Ray Diffraction ◽  
X Ray ◽  
Β Phase ◽  
Α Phase

ABSTRACTThe mechanical alloying behavior of elemental powders in the Nb-Si, Ta-Si, and Nb-Ta-Si systems was examined via X-ray diffraction. The line compounds NbSi2 and TaSi2 form as crystalline compounds rather than amorphous products, but Nb5Si3 and Ta5Si3, although chemically analogous, respond very differently to mechanical milling. The Ta5Si3 composition goes directly from elemental powders to an amorphous product, whereas Nb5Si3 forms as a crystalline compound. The Nb5Si3 compound consists of both the tetragonal room-temperature α phase (c/a = 1.8) and the tetragonal high-temperature β phase (c/a = 0.5). Substituting increasing amounts of Ta for Nb in Nb5Si3 initially stabilizes the α-Nb5Si3 structure preferentially, and subsequently inhibits the formation of a crystalline compound.

Well-defined polyindole–Au NPs nanobrush as a platform for electrochemical oxidation of ethanol

2021 ◽  
Vol 0 (0) ◽  
Author(s):  
Magdalena Warczak ◽  
Marianna Gniadek ◽  
Kamil Hermanowski ◽  
Magdalena Osial
Keyword(s):  
Conducting Polymers ◽  
Hybrid Material ◽  
Noble Metals ◽  
Electrochemical Impedance ◽  
Electrochemical Sensing ◽  
Alkaline Media ◽  
X Ray Diffraction ◽  
Long Term Stability ◽  
Sensing Applications ◽  
Energy Conversion Devices

Abstract Over the recent decades, conducting polymers have received great interest in many fields including microelectronics, energy conversion devices, and biosensing due to their unique properties like electrical conductivity, stability, and simple synthesis. Modification of conducting polymers with noble metals e.g. gold enhances their properties and opens new opportunities to also apply them in other fields like electrocatalysis. Here, we focus on the synthesis of hybrid material based on polyindole (PIN) nanobrush modified with gold nanoparticles and its application towards electrooxidation of ethanol. The paper presents systematic studies from synthesis to electrochemical sensing applications. For the characterization of PIN–Au composites, scanning electron microscopy and X-ray diffraction analyses were used. The electrocatalytic performance of the proposed hybrid material towards alcohol oxidation was studied in alkaline media by cyclic voltammetry, chronoamperometry, and electrochemical impedance spectroscopy techniques. The results show that PIN–Au hybrid can be employed as an effective and sensitive platform for the detection of alcohols, which makes it a promising material in electrocatalysis or sensors. Moreover, the proposed composite exhibits electrocatalytic activity towards ethanol oxidation, which combined with its good long-term stability opens the opportunity for its application in fuel cells.

Sign in / Sign up

Export Citation Format

Share Document