scholarly journals All Single-Mode-Fiber Supercontinuum Source Setup for Monitoring of Multiple Gases Applications

Sensors ◽  
2020 ◽  
Vol 20 (11) ◽  
pp. 3239
Author(s):  
Javier A. Martin-Vela ◽  
Eloisa Gallegos-Arellano ◽  
Juan M. Sierra-Hernández ◽  
Julián M. Estudillo-Ayala ◽  
Daniel Jauregui-Vázquez ◽  
...  
Keyword(s):  
Gas Sensing ◽  
Low Cost ◽  
High Sensitivity ◽  
Single Mode ◽  
Single Mode Fiber ◽  
Experimental Results ◽  
Hitran Database ◽  
Broadband Absorption ◽  
Sensing System ◽  
Absorption Technique

In this paper, a gas sensing system based on a conventional absorption technique using a single-mode-fiber supercontinuum source (SMF-SC) is presented. The SC source was implemented by channeling pulses from a microchip laser into a one kilometer long single-mode fiber (SMF), obtaining a flat high-spectrum with a bandwidth of up to 350 nm in the region from 1350 to 1700 nm, and high stability in power and wavelength. The supercontinuum radiation was used for simultaneously sensing water vapor and acetylene gas in the regions from 1350 to 1420 nm and 1510 to 1540 nm, respectively. The experimental results show that the absorption peaks of acetylene have a maximum depth of approximately 30 dB and contain about 60 strong lines in the R and P branches, demonstrating a high sensitivity of the sensing setup to acetylene. Finally, to verify the experimental results, the experimental spectra are compared to simulations obtained from the Hitran database. This shows that the implemented system can be used to develop sensors for applications in broadband absorption spectroscopy and as a low-cost absorption spectrophotometer of multiple gases.

scholarly journals A Micro Bubble Structure Based Fabry–Perot Optical Fiber Strain Sensor with High Sensitivity and Low-Cost Characteristics

Sensors ◽  
2017 ◽  
Vol 17 (3) ◽  
pp. 555 ◽  
Author(s):  
Lu Yan ◽  
Zhiguo Gui ◽  
Guanjun Wang ◽  
Yongquan An ◽  
Jinyu Gu ◽  
...  
Keyword(s):  
Low Cost ◽  
Strain Sensor ◽  
Glass Tube ◽  
High Sensitivity ◽  
Single Mode ◽  
Single Mode Fiber ◽  
Fabry Perot ◽  
Micro Bubble ◽  
Bubble Structure ◽  
Cost Characteristics

A high-sensitivity, low-cost, ultrathin, hollow fiber micro bubble structure was proposed; such a bubble can be used to develop a high-sensitivity strain sensor based on a Fabry–Perot interferometer (FPI). The micro bubble is fabricated at the fiber tip by splicing a glass tube to a single mode fiber (SMF) and then the glass tube is filled with gas in order to expand and form a micro bubble. The sensitivity of the strain sensor with a cavity length of about 155 μm and a bubble wall thickness of about 6 μm was measured to be up to 8.14 pm/μϵ.

scholarly journals A High Sensitivity Temperature Sensing Probe Based on Microfiber Fabry-Perot Interference

Sensors ◽  
2019 ◽  
Vol 19 (8) ◽  
pp. 1819 ◽  
Author(s):  
Zhoubing Li ◽  
Yue Zhang ◽  
Chunqiao Ren ◽  
Zhengqi Sui ◽  
Jin Li
Keyword(s):  
Low Cost ◽  
High Sensitivity ◽  
Single Mode ◽  
Single Mode Fiber ◽  
Temperature Sensing ◽  
Compact Structure ◽  
Fabry Perot ◽  
Temperature Monitor ◽  
Core Fiber ◽  
Fitting In

In this paper, a miniature Fabry-Perot temperature probe was designed by using polydimethylsiloxane (PDMS) to encapsulate a microfiber in one cut of hollow core fiber (HCF). The microfiber tip and a common single mode fiber (SMF) end were used as the two reflectors of the Fabry-Perot interferometer. The temperature sensing performance was experimentally demonstrated with a sensitivity of 11.86 nm/°C and an excellent linear fitting in the range of 43–50 °C. This high sensitivity depends on the large thermal-expansion coefficient of PDMS. This temperature sensor can operate no higher than 200 °C limiting by the physicochemical properties of PDMS. The low cost, fast fabrication process, compact structure and outstanding resolution of less than 10−4 °C enable it being as a promising candidate for exploring the temperature monitor or controller with ultra-high sensitivity and precision.

Switchable and tunable linear cavity erbium-doped fiber laser based on FBGs embedded in Sagnac rings

Laser Physics ◽  
2021 ◽  
Vol 32 (1) ◽  
pp. 015101
Author(s):  
Gangxiao Yan ◽  
Weihua Zhang ◽  
Peng Li ◽  
Qiuhao Jiang ◽  
Meng Wu ◽  
...  
Keyword(s):  
Fiber Laser ◽  
Low Cost ◽  
Single Mode ◽  
Optical Signal ◽  
Single Mode Fiber ◽  
Hole Burning ◽  
Linear Cavity ◽  
Erbium Doped ◽  
Optical Fiber Sensing ◽  
Birefringence Effect

Abstract A switchable and tunable erbium-doped fiber laser with a linear cavity based on fiber Bragg gratings embedded in Sagnac rings is proposed and experimentally verified. Due to the stress birefringence effect and the polarized hole burning effect, which are introduced into the single-mode fiber in the polarization controllers (PCs) by the PCs, the designed laser can achieve seven kinds of laser-states output including three kinds of single-wavelength laser states, three kinds of dual-wavelength laser states and one kind of triple-wavelength laser state. The optical signal-to-noise ratios of the output wavelengths are all higher than 52 dB, and the wavelength shifts are all less than 0.04 nm. Furthermore, the temperature tuning of the wavelength range is also researched, which is about 1.2 nm. Due to advantages, such as low cost, simple structure, easy switching and multiple laser states, the designed laser has great application potential in laser radar, optical fiber sensing and so on.

Fabrication, Characterization and Microsensing of Whispering-Gallery Mode Micro-Coupling Systems

2008 ◽  
Author(s):  
Qiulin Ma ◽  
Tobias Rossmann ◽  
Zhixiong Guo
Keyword(s):  
Transmission Loss ◽  
Coupling Efficiency ◽  
High Sensitivity ◽  
Single Mode ◽  
Whispering Gallery Mode ◽  
Single Mode Fiber ◽  
Whispering Gallery ◽  
Coupling System ◽  
Wide Range ◽  
Micro Sensor

An optical micro-coupling system of whispering-gallery mode usually consists of a resonator (e.g. a sphere) and a coupler (e.g. a taper). In this report, silica microspheres of 50–500 μm in diameter are fabricated by hydrogen flame fusing of an end of a single mode fiber or fiber taper. Fiber tapers are fabricated by the method of heating and pulling that meets an adiabatic condition. Taper’s waist diameter can routinely be made less than 1 μm and almost zero transmission loss in a taper is achieved which allows an effective and phase-matched coupling for a wide range sizes of microspheres. Both resonators and couplers’ surface microstructure and shapes are examined by scanning electronic microscopy. Three regimes of coupling are achieved, enabling a good flexibility to control Q value and coupling efficiency of a micro-coupling system. Whispering gallery mode shift is used to demonstrate a novel temperature micro-sensor. Its sensitivity determined from actual experimental results agrees well with the theoretical value. A concept of using the photon’s cavity ring down (CRD) in the microsphere to make a novel high-sensitivity trace gas micro-sensor is proposed. The CRD time constant when ammonia is chosen as the analyte gas is predicted using the simulated absorption lines.

Low-cost and high-efficiency single-mode-fiber interfaces to silicon photonic circuits

2020 ◽  
Vol 465 ◽  
pp. 125554 ◽  
Author(s):  
Xian Zhang ◽  
Bin Chen ◽  
Ziliang Ruan ◽  
Weixi Liu ◽  
Pengxin Chen ◽  
...  
Keyword(s):  
High Efficiency ◽  
Low Cost ◽  
Single Mode ◽  
Single Mode Fiber ◽  
Photonic Circuits ◽  
Silicon Photonic

scholarly journals INVESTIGATING THE EFFECT OF TAPER LENGTH ON SENSITIVITY OF THE TAPERED-FIBER BASED TEMPERATURE SENSOR

2016 ◽  
Vol 78 (3) ◽  
Author(s):  
Baktiar Musa ◽  
Yasmin Mustapha Kamil ◽  
Muhammad Hafiz Abu Bakar ◽  
Ahmad Shukri Mohd Noor ◽  
Alyani Ismail ◽  
...  
Keyword(s):  
Temperature Sensor ◽  
Optimum Parameter ◽  
Low Cost ◽  
High Sensitivity ◽  
Single Mode ◽  
Careful Selection ◽  
Tapered Fiber ◽  
Tapered Optical Fiber ◽  
Good Repeatability ◽  
Selection Of

A temperature sensor using single-mode tapered fiber is presented. To better understand the behaviour of a tapered optical fiber, transmission experiments with different taper profiles, specifically waist length were performed. The effects of taper profiles on the sensitivity of the sensor were also investigated. It is demonstrated that careful selection of the taper profile can increase the sensitivity of the sensor. In our experiment, a good temperature sensing result was achieved using the optimum parameter. The best sensitivity achieved was 45.5 pm/°C that measured the range of temperature from 30°C to 120°C. The fabricated sensors are easy to fabricate and relatively low cost. Our results indicate that the tapered fiber based temperature sensor has high sensitivity and good repeatability.  

Experimental Research of Strain and Temperature Based on EFPI Sensor

2011 ◽  
Vol 130-134 ◽  
pp. 4185-4188
Author(s):  
Xiu Feng Yang ◽  
Chun Yu Zhang ◽  
Zheng Rong Tong
Keyword(s):  
Low Cost ◽  
Single Mode ◽  
Single Mode Fiber ◽  
Good Reliability ◽  
High Repetition ◽  
Sensing Applications ◽  
Fabry Perot ◽  
Wet Chemical ◽  
The Many ◽  
Multi Mode

An extrinsic Fabry-Perot (F-P) interferometric (EFPI) sensor by using simple etching and fusing method is proposed and demonstrated. The cavity is formed by wet chemical etching of multi-mode fiber (MMF) end face in hydrofluoric acid solutions, and then it is fused to the end of a single-mode fiber (SMF) to form an extrinsic F-P structure. The strain and temperature of EFPI sensor are studied experimentally. The experimental results show that the interference wavelength becomes 2.648nm longer while the strain increases from 0N to 637N, and the strain sensitivity is about 0.004nm/N, and linearity is 0.999. The interference wavelength becomes 0.032nm shorter while the temperature increases from 20°C to 100°C. This kind of sensor has the many advantages of easy fabrication, good reliability, high-repetition, small size, low cost and mass-production, which offers great prospect for sensing applications.

Gas Sensing Properties of TiO2 and SnO2 Nanopowders Obtained through Gel Combustion

2006 ◽  
Vol 45 ◽  
pp. 1828-1833
Author(s):  
Fabio A. Deorsola ◽  
P. Mossino ◽  
Ignazio Amato ◽  
Bruno DeBenedetti ◽  
A. Bonavita ◽  
...  
Keyword(s):  
Response Time ◽  
Metal Oxides ◽  
Gas Sensing ◽  
Low Cost ◽  
High Sensitivity ◽  
Fast Response ◽  
High Specific Surface Area ◽  
Research Field ◽  
Wide Range ◽  
Gel Combustion

Nanostructured semiconductor metal oxides have played a central role in the gas sensing research field, because of their high sensitivity, selectivity and low response time. Among all the processes, developed for the synthesis of nanostructured metal oxides, gel combustion seems to be the most promising route due to low-cost precursors and simplicity of the process. It combines chemical gelation and combustion, involving the formation of a gel from an acqueous solution and an exothermic redox reaction, yielding to very porous and softly agglomerated nanopowders. In this work, nanostructured tin oxide, SnO2, and titanium oxide, TiO2, have been synthesized through gel combustion. Powders showed nanometric particle size and high specific surface area. The so-obtained TiO2 and SnO2 nanopowders have been used as sensitive element of resistive λ sensor and ethanol sensor respectively, realized depositing films of nanopowders dispersed in water onto alumina substrates provided with Pt contacts and heater. TiO2-based sensors showed at high temperature good response, fast response time, linearity in a wide range of O2 concentration and long-term stability. SnO2-based sensors have shown high sensitivity to low concentrations of ethanol at moderate temperature.

Low-Cost Active-Alignment of Single-Mode Fiber-Arrays

2006 ◽  
Author(s):  
D. Weiland ◽  
M. Luetzelschwab ◽  
M.P.Y. Desmulliez ◽  
A. Missoffe ◽  
C. Beck
Keyword(s):  
Low Cost ◽  
Single Mode ◽  
Single Mode Fiber ◽  
Fiber Arrays
Sign in / Sign up

Export Citation Format

Share Document