scholarly journals A Low-Profile End-Fire Conformal Surface Wave Antenna with Capacitive Feed Structure

Sensors ◽  
2020 ◽  
Vol 20 (24) ◽  
pp. 7054
Author(s):  
Legen Dai ◽  
Yongjun Xie ◽  
Huai Wang
Keyword(s):  
Surface Wave ◽  
High Gain ◽  
Metal Plate ◽  
Center Frequency ◽  
Fire Performance ◽  
Flight Vehicles ◽  
Operating Wavelength ◽  
Wave Antenna ◽  
Low Profile ◽  
Profile Height

A high end-fire gain, low-profile surface wave antenna with capacitive feed structure is presented in this paper. The proposed dielectric-metal surface wave antenna is composed of a dielectric slab that is mounted on a metal carrier and a low-profile feed structure. The feed structure is composed of a monopole radiation pin that is loaded with a circular metal plate and a grounding pin. The profile height of the antenna is only one-tenth of the operating wavelength. With a good end-fire performance and low profile, the antenna is very suitable to be conformally mounted on the surface of flight vehicles. The proposed antenna was designed and manufactured at the center frequency of 6 GHz. Measured results demonstrated that the proposed antenna had a bandwidth of 7.33%, ranging from 5.89 to 6.33 GHz, and the antenna reached a high gain of 9.76 dBi with a length of 122.96 mm (2.45 λ) in the end-fire direction.

scholarly journals Millimeter Wave Fabry-Perot Resonator Antenna Fed by CPW with High Gain and Broadband

2016 ◽  
Vol 2016 ◽  
pp. 1-7 ◽  
Author(s):  
Xue-Xia Yang ◽  
Guan-Nan Tan ◽  
Bing Han ◽  
Hai-Gao Xue
Keyword(s):  
Millimeter Wave ◽  
Coplanar Waveguide ◽  
Dielectric Substrate ◽  
High Gain ◽  
Center Frequency ◽  
Impedance Bandwidth ◽  
Gain Bandwidth ◽  
Broad Bandwidth ◽  
Low Profile ◽  
Fabry Perot

A novel millimeter wave coplanar waveguide (CPW) fed Fabry-Perot (F-P) antenna with high gain, broad bandwidth, and low profile is reported. The partially reflective surface (PRS) and the ground form the F-P resonator cavity, which is filled with the same dielectric substrate. A dual rhombic slot loop on the ground acts as the primary feeding antenna, which is fed by the CPW and has broad bandwidth. In order to improve the antenna gain, metal vias are inserted surrounding the F-P cavity. A CPW-to-microstrip transition is designed to measure the performances of the antenna and extend the applications. The measured impedance bandwidth ofS11less than −10 dB is from 34 to 37.7 GHz (10.5%), and the gain is 15.4 dBi at the center frequency of 35 GHz with a 3 dB gain bandwidth of 7.1%. This performance of the antenna shows a tradeoff among gain, bandwidth, and profile.

scholarly journals Wideband Flush-Mounted Surface Wave Antenna of Very Low Profile

2015 ◽  
Vol 63 (6) ◽  
pp. 2430-2438 ◽  
Author(s):  
Zhuozhu Chen ◽  
Zhongxiang Shen
Keyword(s):  
Surface Wave ◽  
Wave Antenna ◽  
Low Profile

scholarly journals Metasurfaces for Reconfiguration of Multi-Polarization Antennas and Van Atta Reflector Arrays

Electronics ◽  
2020 ◽  
Vol 9 (8) ◽  
pp. 1262
Author(s):  
Mohammed Alharbi ◽  
Meshaal A. Alyahya ◽  
Subramanian Ramalingam ◽  
Anuj Y. Modi ◽  
Constantine A. Balanis ◽  
...  
Keyword(s):  
Surface Wave ◽  
Antenna Arrays ◽  
Performance Enhancement ◽  
High Gain ◽  
Wave Antenna ◽  
Recent Developments ◽  
Four Square ◽  
And Performance ◽  
Retrodirective Array ◽  
Ring Elements

This paper discusses the application of metasurfaces for three different classes of antennas: reconfiguration of surface-wave antenna arrays, realization of high-gain polarization-reconfigurable leaky-wave antennas (LWAs), and performance enhancement of van Atta retrodirective reflectors. The proposed surface-wave antenna is designed by embedding four square ring elements within a metasurface, which improves matching and enhances the gain when compared to conventional square-ring arrays. The design for linear polarization comprises of a 1 × 4 arrangement of ring elements, with a 0.56λ spacing, placed amidst periodic patches. A 2 × 2 arrangement of ring elements is utilized for reconfiguration from linear to circular polarization, where a similar peak gain with better port isolation is realized. A prototype of the 2 × 2 array is fabricated and measured; a good agreement is observed between simulations and measurements. In addition, the concepts of the design of polarization-diverse holographic metasurface LWAs that form a pencil beam in the desired direction with a reconfigurable polarization are discussed. Moreover, recent developments incorporating polarization-reconfigurability in metasurface LWAs are briefly reviewed. In the end, the theory of van Atta arrays is outlined and their monostatic RCS is reviewed. A conventional retrodirective array is designed using aperture-coupled patch antennas with a microstrip-line feeding network, where the scattering from the structure itself degrades the performance of the reflector. This is followed by the integration of judiciously synthesized metasurfaces to reconfigure and improve the performance of retrodirective reflectarrays by removing the above-mentioned undesired scattering from the structure.

scholarly journals High-Gain Millimeter-Wave Patch Array Antenna for Unmanned Aerial Vehicle Application

Sensors ◽  
2021 ◽  
Vol 21 (11) ◽  
pp. 3914
Author(s):  
Kyei Anim ◽  
Jung-Nam Lee ◽  
Young-Bae Jung
Keyword(s):  
Surface Wave ◽  
Millimeter Wave ◽  
Large Scale ◽  
High Gain ◽  
Metal Plate ◽  
Array Antenna ◽  
Wave Radiation ◽  
Wave Band ◽  
Large Patch ◽  
Large Coupling

A high-gain millimeter-wave patch array antenna is presented for unmanned aerial vehicles (UAVs). For the large-scale patch array antenna, microstrip lines and higher-mode surface wave radiations contribute enormously to the antenna loss, especially at the millimeter-wave band. Here, the element of a large patch array antenna is implemented with a substrate integrated waveguide (SIW) cavity-backed patch fed by the aperture-coupled feeding (ACF) structure. However, in this case, a large coupling aperture is used to create strongly bound waves, which maximizes the coupling level between the patch and the feedline. This approach helps to improve antenna gain, but at the same time leads to a significant level of back radiation due to the microstrip feedline and unwanted surface-wave radiation, especially for the large patch arrays. Using the SIW cavity-backed patch and stripline feedline of the ACF in the element design, therefore, provides a solution to this problem. Thus, a full-corporate feed 32 × 32 array antenna achieves realized gain of 30.71–32.8 dBi with radiation efficiency above 52% within the operational band of 25.43–26.91 GHz. The fabricated antenna also retains being lightweight, which is desirable for UAVs, because it has no metal plate at the backside to support the antenna.

scholarly journals Double Meander Dipole Antenna Array with Enhanced Bandwidth and Gain

2021 ◽  
Vol 2021 ◽  
pp. 1-8
Author(s):  
Halgurd N. Awl ◽  
Rashad H. Mahmud ◽  
Bakhtiar A. Karim ◽  
Yadgar I. Abdulkarim ◽  
Muharrem Karaaslan ◽  
...  
Keyword(s):  
Antenna Array ◽  
High Gain ◽  
Dipole Antenna ◽  
Operating Frequency ◽  
Center Frequency ◽  
Impedance Bandwidth ◽  
Frequency Range ◽  
Wide Bandwidth ◽  
Low Profile ◽  
Operating Frequency Range

In this paper, a new design of high gain and wide bandwidth microstrip patch antenna array containing double meander dipole structure is proposed. Two in-phase resonant frequencies in the Ku-band (12–18 GHz) could be achieved in the double meander dipole array structure, which lead to enhance impedance bandwidth without costing extra design section. Besides, further enhanced gain of 2 dBi of the array over the entire operating frequency range has been achieved by introducing a double-layer substrate technique. The proposed antenna has been fabricated using the E33 model LPKF prototyping PCB machine. The measurement results have been performed, and they are in very good agreement with the simulation results. The measured –10 dB impedance bandwidth indicates that the array provides a very wide bandwidth which is around 30% at the center frequency of 15.5 GHz. A stable gain with a peak value of 10 dBi is achieved over the operating frequency range. The E- and H-plane radiation patterns are simulated, and a very low sidelobe level is predicted. The proposed antenna is simple and has relatively low-profile, and it could be a good candidate for millimeter wave communications.

Sign in / Sign up

Export Citation Format

Share Document