scholarly journals Microwave Induction Heating of Polymer-Modified Asphalt Materials for Self-Healing and Deicing

2021 ◽  
Vol 13 (18) ◽  
pp. 10129
Author(s):  
Mansour Fakhri ◽  
Sajad Javadi ◽  
Reza Sedghi ◽  
Alireza Sassani ◽  
Ali Arabzadeh ◽  
...  
Keyword(s):  
Induction Heating ◽  
Microwave Field ◽  
Asphalt Binder ◽  
Self Healing ◽  
Polymer Modification ◽  
Crack Healing ◽  
Ice Melting ◽  
Field Exposure ◽  
Modified Asphalt ◽  
Asphalt Mastic

This study evaluates the influence of polymer-modification on the induction heating capability of asphalt mastic in a microwave field, and investigates how effectively this approach can be utilized for ice melting and self-healing purposes. To this end, different asphalt mastic mixtures with different polymer-modification and mixing procedures were tested under microwave field exposure for induction heating capability, ice-melting ability, and self-healing capacity. The mixtures were made through warm-mix and hot-mix procedures with four bituminous binders, including virgin (unmodified) asphalt and the same binder modified with three types of polymers. The results showed the effectiveness of microwave induction heating of asphalt mastic for both crack-healing and deicing purposes. The binder type was found to influence the ice melting and crack healing rates, such that using a warm-mix asphalt binder resulted in a more efficient heat generation and conduction than using a virgin asphalt binder. While polymer-modification undermined induction-heating, ice-melting, and self-healing performances, SBS-modified asphalt binders exhibited better performance than the other polymer-modified binders.

scholarly journals Investigation of the Effect of Induction Heating on Asphalt Binder Aging in Steel Fibers Modified Asphalt Concrete

Materials ◽  
2019 ◽  
Vol 12 (7) ◽  
pp. 1067 ◽  
Author(s):  
Hechuan Li ◽  
Jianying Yu ◽  
Shaopeng Wu ◽  
Quantao Liu ◽  
Yuanyuan Li ◽  
...  
Keyword(s):  
Induction Heating ◽  
Asphalt Concrete ◽  
Asphalt Binder ◽  
Steel Fibers ◽  
Asphalt Binders ◽  
Carbonyl Index ◽  
Modified Asphalt ◽  
Concrete Damage ◽  
The Difference ◽  
Binder Aging

Induction heating is a valuable technology to repair asphalt concrete damage inside. However, in the process of induction heating, induced particles will release a large amount of heat to act on asphalt binder in a short time. The purpose of this paper was to study the effect of induction heating on asphalt binder aging in steel fibers modified asphalt concrete. The experiments were divided into two parts: induction heating of Dramix steel fibers coated with asphalt binder (DA) and steel wool fibers modified asphalt concrete. After induction heating, the asphalt binders in the samples were extracted for testing aging indices with Fourier Transform Infrared (FTIR), Dynamic Shear Rheometer (DSR), and Four-Components Analysis (FCA) tests. The aging of asphalt binder was analyzed identifying the change of chemical structure, the diversification of rheological properties, and the difference of component. The experiments showed that the binder inside asphalt concrete began aging during induction heating due to thermal oxygen reaction and volatilization of light components. However, there was no peak value of the carbonyl index after induction heating of ten cycles, and the carbonyl index of DA was equivalent to that of binder in asphalt concrete after three induction heating cycles, which indicated the relatively closed environment inside asphalt concrete can inhibit the occurrence of the aging reaction.

scholarly journals The Self-Healing Performance of Carbon-Based Nanomaterials Modified Asphalt Binders Based on Molecular Dynamics Simulations

2021 ◽  
Vol 7 ◽  
Author(s):  
Yan Gong ◽  
Jian Xu ◽  
Er-hu Yan ◽  
Jun-hua Cai
Keyword(s):  
Healing Process ◽  
Asphalt Binder ◽  
Mean Square Displacement ◽  
The Self ◽  
Asphalt Binders ◽  
Self Healing ◽  
Modified Asphalt ◽  
Healing Efficiency ◽  
Carbon Based Nanomaterials ◽  
Carbon Based

In this study, the molecular dynamics simulation was used to explore the effects of carbon-based nanomaterials as binder modifiers on self-healing capability of asphalt binder and to investigate the microscopic self-healing process of modified asphalt binders under different temperature. An asphalt average molecular structure model of PEN70 asphalt binder was constructed firstly. Further, three kinds of carbon-based nanomaterials were added at three different percentages ranging from 0.5 to 1.5% to the base binder to study their effects on the self-healing capability, including two carbon nanotubes (CNT1 and CNT2) and graphene nanoflakes. Combining with the three-dimensional (3D) microcrack model to simulate the asphalt self-healing process, the density analysis, relative concentration analysis along OZ direction, and mean square displacement analysis were performed to investigate the temperature sensitive self-healing characters. Results showed that the additions of CNTs were effective in enhancing the self-healing efficiency of the plain asphalt binder. By adding 0.5% CNT1 and 0.5% CNT2, about 652% and 230% of the mean square displacement of plain asphalt binder were enhanced at the optimal temperatures. However, the use of graphene nanoflakes as an asphalt modifier did not provide any noticeable changes on the self-healing efficiency. It can be found that the self-healing capability of the asphalt was closely related to the temperature. For base asphalt, the self-healing effect became especially high at the phase transition temperature range, while, for the modified asphalt, the enhancement of the self-healing capability at the low phase transition temperature (15°C) became negligible. In general, the optimal healing temperature range of the CNTs modified asphalt binders is determined as 45–55°C and the optimal dosage of the CNTs is about 0.5% over the total weight of the asphalt binder. Considering the effect of carbon-based nanomaterials on the self-healing properties, the recommended carbon-based nanomaterials modifier is CNT1 with the aspect ratio of 1.81.

scholarly journals Enhancing Effect of Waste Engine Oil Bottom Incorporation on the Performance of CR+SBS Modified Bitumen: A Sustainable and Environmentally-Friendly Solution for Wastes

2021 ◽  
Vol 13 (22) ◽  
pp. 12772
Author(s):  
Changjiang Liu ◽  
Qiuping Wang
Keyword(s):  
Asphalt Binder ◽  
Engine Oil ◽  
Chemical Compositions ◽  
Self Healing ◽  
Temperature Property ◽  
Modified Bitumen ◽  
Modified Asphalt ◽  
Waste Engine Oil ◽  
Sbs Modified Asphalt ◽  
Low Temperature Property

Waste engine oil bottom (WEOB) is a hazardous waste whose effect as an additive to CR+SBS modified asphalt is rarely studied. In this study, the CR+SBS asphalt binder was modified with WEOB in different concentrations (3, 6, and 9 wt%). The GC–MS and FTIR were performed to evaluate the chemical compositions of WEOB and WEOBCR+SBS asphalt. The results showed that the main constituents of WEOB were similar to the functional groups of asphalt, along with maleic anhydride (MAH). Pavement performance-related rheological tests such as RV, temperature sweep (TS), FS, MSCR, and BBR were carried out. Results show that WEOBCR+SBS-6 exhibited the best high- and low-temperature property, followed by CR+SBS-3 and CR+SBS-9. Fluorescence microscope (FM) test, bar thin layer chromatograph (BTLC) test, FTIR, and AFM tests were carried out to evaluate the micro-morphologies and modification mechanism. The analysis revealed increased trends in resin fraction as opposed to asphaltene fraction with the increase of WEOB content. FTIR analysis revealed that the amide groups in WEOBCR+SBS asphalt bonded to the free radicals of CR. Moreover, a modification mechanism was elaborated. WEOB strengthens the cross-linked structure of CR+SBS polymers, reacting with SBS to graft onto MAH-g-SBS, and the free radical of CR interacts with the amide group in WEOB to form a bond. In addition, the content of lightweight components and surface roughness of SBS specimens were in good correlation, which contributed to the rutting resistance and adhesion and self-healing performance.

scholarly journals Laboratory Evaluation on Performance of Fiber-Modified Asphalt Mixtures Containing High Percentage of RAP

2020 ◽  
Vol 2020 ◽  
pp. 1-9
Author(s):  
Yuefeng Zhu ◽  
Yanwei Li ◽  
Chundi Si ◽  
Xiaote Shi ◽  
Yaning Qiao ◽  
...  
Keyword(s):  
Low Temperature ◽  
Asphalt Binder ◽  
Temperature Stability ◽  
Asphalt Mixtures ◽  
Self Healing ◽  
Test Results ◽  
Moisture Susceptibility ◽  
Modified Asphalt ◽  
Modified Binders ◽  
Different Types

In recent years, the significant demand for sustainable paving materials has led to a rapid increase in the utilization of reclaimed asphalt pavement (RAP) materials. When RAP is mixed with virgin asphalt concrete, particularly when its percentage is high, performance of the binder and asphalt concrete can be adversely affected. For this reason, different types of additives need to be identified and evaluated beforehand to mitigate the adverse effects. In this study, different types of fiber materials were identified and selected as binder/mixture additives, including lignin fiber (LF), polyester fiber (PF), and basalt fiber (BF). Various samples of fiber-modified binders and asphalt mixtures with different RAP contents (0%, 20%, and 40%) were prepared and were evaluated using two sets of laboratory testing: (i) dynamic shear rheometer (DSR) and bending beam rheometer (BBR) tests were performed to study the rheological properties of fiber-modified binders; (ii) the wheel tracking test, bending creep test, moisture susceptibility test, fatigue test, and self-healing fatigue test were conducted to characterize the laboratory properties of fiber-modified RAP mixtures. Test results for the modified binders show that the BF-modified binder has the greatest positive effect on the high-temperature performance of the asphalt binder, followed by PF- and LF-modified binders. However, the virgin asphalt shows the best low-temperature property than the fiber-modified asphalt binder. Test results for the whole RAP mixtures show that all fibers have a significant effect on the properties (including high- and low-temperature stability, moisture susceptibility, fatigue, and self-healing ability) of RAP mixtures. Among them, adding BF shows the greatest improvement in high-temperature stability, fatigue resistance, and self-healing ability of RAP mixtures. LF is found to significantly enhance low-temperature properties, and PF can greatly improve the resistance to moisture damage of RAP mixtures. For high percentage of RAP using on sites, adding multiple additives may further enhance its durability.

Snow and ice melting properties of self-healing asphalt mixtures with induction heating and microwave heating

2018 ◽  
Vol 129 ◽  
pp. 871-883 ◽  
Author(s):  
Yihan Sun ◽  
Shaopeng Wu ◽  
Quantao Liu ◽  
Jianfu Hu ◽  
Yuan Yuan ◽  
...  
Keyword(s):  
Microwave Heating ◽  
Induction Heating ◽  
Asphalt Mixtures ◽  
Self Healing ◽  
Ice Melting ◽  
Melting Properties ◽  
Snow And Ice

Creep Compliance of Polymer-Modified Asphalt, Asphalt Mastic, and Hot-Mix Asphalt

2003 ◽  
Vol 1829 (1) ◽  
pp. 33-38 ◽  
Author(s):  
Ota Vacin ◽  
Jiri Stastna ◽  
Ludo Zanzotto
Keyword(s):  
Creep Compliance ◽  
Superposition Principle ◽  
Asphalt Binder ◽  
Tensile Creep ◽  
Asphalt Binders ◽  
Simple Relationship ◽  
Modified Asphalt ◽  
Asphalt Mastic ◽  
Polymer Modified Asphalt ◽  
Time Temperature Superposition Principle

The possibility of using commercial rheometers for comprehensive testing of asphalt binders, asphalt mastics, and hot-mix asphalts (HMA) is explored. Samples of one polymer-modified asphalt, its mix with fine mineral filler (mastic), and one HMA prepared with the same modified asphalt as binders were tested in the dynamic shear rheometer (DSR) and the bending beam rheometer (BBR). All tested materials can be characterized by their discrete relaxation and retardation spectra (under the condition of small deformations). DSR testing was performed in the plate–plate and the torsion bar geometry. From the obtained relaxation and retardation spectra, the shear compliance, J(t), was calculated and compared with the tensile creep compliance, D(t), measured in BBR (both creep and recovery experiments were run). A simple relationship between J(t) and D(t) was found for the asphalt binder and the asphalt mastic. In the case of HMA, the bulk compliance, B(t), contributes to D(t) at short and long times. Both the Boltzmann superposition principle and the time–temperature superposition principle hold very well for all tested materials at low temperatures. There are qualitative differences, in the rheological behavior, of the asphalt binder and asphalt mastic on one side and the HMA on the other. These differences can be seen in dynamic (DSR) as well as in transient (BBR) experiments.

EMPIRICAL AND RHEOLOGICAL PROPERTIES EVALUATION OF MODIFIED ASPHALT BINDER CONTAINING NANOPOLYACRYLATE POLYMER MODIFIER

2015 ◽  
Vol 76 (9) ◽  
Author(s):  
E. Shaffie ◽  
J. Ahmad ◽  
A. K. Arshad ◽  
D. Kamarun
Keyword(s):  
Rheological Properties ◽  
Softening Point ◽  
Asphalt Binder ◽  
Pavement Performance ◽  
Polymer Modification ◽  
Modified Asphalt ◽  
Complex Shear ◽  
Modified Asphalt Binder ◽  
Modified Binder ◽  
Temperature Susceptibility

In this paper, the effects of nanopolyacrylate (NP) in binder modification on the empirical and rheological characteristics of the conventional binder were explored. The empirical and rheological binder properties were characterized using penetration, softening point, viscosity and dynamic shear rheometer (DSR) respectively.  These testings have become useful methods in characterizing of the binder performance on the pavement. The results indicated that NP polymer modification improved the physical properties of the conventional binder such as; penetration, softening point and temperature susceptibility. The results of viscosity test show that the NP polymer modified binder is more viscous than unmodified binder where viscosity increases with the increment of polymer content. The DSR results indicate that the NP polymer improves rheological properties of conventional binder, i.e. increasing the complex shear modulus (G∗) values and rutting parameters (G∗/sin δ), as well as decreasing the phase angle (δ) values. Therefore, it can be concluded that NP polymers considerably improves elastic properties and rutting resistance of binder and thus could be used for enhancing the asphalt pavement performance.

scholarly journals Ice melting properties of steel fiber modified asphalt mixtures with induction heating

2017 ◽  
Vol 182 ◽  
pp. 012042 ◽  
Author(s):  
Hao Fang ◽  
Yihan Sun ◽  
Quantao Liu ◽  
Bin Li ◽  
Shaopeng Wu ◽  
...  
Keyword(s):  
Induction Heating ◽  
Steel Fiber ◽  
Asphalt Mixtures ◽  
Ice Melting ◽  
Modified Asphalt ◽  
Melting Properties

Fracture toughness of polymer-modified asphalt concrete at low temperatures

2003 ◽  
Vol 30 (2) ◽  
pp. 406-413 ◽  
Author(s):  
Kwang W Kim ◽  
Seung Jun Kweon ◽  
Young S Doh ◽  
Tae-Soon Park
Keyword(s):  
Fracture Toughness ◽  
Low Temperature ◽  
Asphalt Concrete ◽  
Low Temperatures ◽  
Asphalt Binder ◽  
Polymer Modification ◽  
Modified Asphalt ◽  
Temperature Damage ◽  
Polymer Modified Asphalt ◽  
Styrene Butadiene

The fracture toughness of asphalt concrete increases at low temperature and then decreases at temperatures below a certain level. Some polymers are known to have the property of improving the temperature susceptibility of asphalt binder at low temperatures. Therefore, this study evaluated the fracture toughness (KIC) of some polymer-modified asphalt concretes. Low-density polyethylene (LDPE), styrene–butadiene–styrene (SBS), and a mixed polymer of LDPE and SBS were used in this study. The fracture toughness KIC of normal asphalt concrete was compared with that of polymer-modified asphalt (PMA) concrete, and the effectiveness of polymer modification against falling values of KIC was evaluated at low temperatures. The results showed that PMA concretes, in general, showed better KIC than normal asphalt concretes, and the temperature at which the highest KIC was obtained was lower than that in the case of normal asphalt concrete. Therefore, the PMA concretes evaluated in this study had better fracture resistance than normal asphalt at low temperatures.Key words: asphalt concrete, polymer-modified asphalt, PMA, fracture toughness, differential thermal contraction, low-temperature damage.

Sign in / Sign up

Export Citation Format

Share Document