scholarly journals Optimization of the Auxiliary-Beam System in Railway Bridge Vibration Mitigation Using FEM Simulation and Genetic Algorithms

Symmetry ◽  
2019 ◽  
Vol 11 (9) ◽  
pp. 1089
Author(s):  
Jacobo Baldonedo ◽  
José A. López-Campos ◽  
Marcos López ◽  
Enrique Casarejos ◽  
José R. Fernández
Keyword(s):  
Genetic Algorithm ◽  
Finite Element ◽  
Finite Element Model ◽  
Structural Parameters ◽  
Fem Simulation ◽  
Element Model ◽  
Design Parameters ◽  
Vibration Mitigation ◽  
Resonance Effects ◽  
Beam System

In this paper, we present the optimization of a vibration mitigation system for railway bridges. These structures are subjected to significant moving loads, whose dynamic characteristics may produce resonance effects, compromising the integrity of the bridge and the security of the passengers if the speed or the load of the train is not controlled. The study focuses on the Auxiliary Beam system. It consists of a beam located under the bridge and connected to the slab by viscous dampers. The symmetry of the problem allowed for the use of a 2D Finite Element model of the system. This model was used together with a genetic algorithm in order to evaluate the behaviour of different candidates and to optimize the design parameters: the inertia of the beam and the damper coefficient. The goal of the optimization process is to minimize the acceleration of the bridge while adding the lightest mitigation system possible. The combination of a Finite Element Model and Genetic Algorithm helps to address the complex problem and to find an optimized set of structural parameters. The system finally shows good behaviour for optimal parameters.

scholarly journals Sensitivity Analysis of the Influence of Structural Parameters on Dynamic Behaviour of Highly Redundant Cable-Stayed Bridges

2013 ◽  
Vol 2013 ◽  
pp. 1-11 ◽  
Author(s):  
B. Asgari ◽  
S. A. Osman ◽  
A. Adnan
Keyword(s):  
Sensitivity Analysis ◽  
Finite Element ◽  
Finite Element Model ◽  
Model Updating ◽  
Structural Parameters ◽  
Element Model ◽  
Structural Behavior ◽  
Model Tuning ◽  
The Finite Element Model ◽  
Cable Stayed Bridges

The model tuning through sensitivity analysis is a prominent procedure to assess the structural behavior and dynamic characteristics of cable-stayed bridges. Most of the previous sensitivity-based model tuning methods are automatic iterative processes; however, the results of recent studies show that the most reasonable results are achievable by applying the manual methods to update the analytical model of cable-stayed bridges. This paper presents a model updating algorithm for highly redundant cable-stayed bridges that can be used as an iterative manual procedure. The updating parameters are selected through the sensitivity analysis which helps to better understand the structural behavior of the bridge. The finite element model of Tatara Bridge is considered for the numerical studies. The results of the simulations indicate the efficiency and applicability of the presented manual tuning method for updating the finite element model of cable-stayed bridges. The new aspects regarding effective material and structural parameters and model tuning procedure presented in this paper will be useful for analyzing and model updating of cable-stayed bridges.

scholarly journals Investigation on aerodynamic characteristics of bionic membrane nano rotor

2021 ◽  
Vol 18 ◽  
pp. 175682932110433
Author(s):  
Shanyong Zhao ◽  
Zhen Liu ◽  
Ke Lu ◽  
Dacheng Su ◽  
Shangjing Wu
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Structural Parameters ◽  
Element Model ◽  
Aerodynamic Characteristics ◽  
Aerodynamic Performance ◽  
Dynamics Model ◽  
Interaction Method ◽  
Calculation Results ◽  
The Finite Element Model

In this paper, the bionic membrane structure is introduced to improve the aerodynamic performance of nano rotor at the low Reynolds number. The aerodynamic characteristics of nano rotor made of hyperelastic material as membrane blades are studied. Firstly, based on the hyperelastic constitutive model, a finite element model of the rotor is established and compared with the results of the modal test to verify the accuracy of the model. Then the computational fluid dynamics model of membrane nano rotor is established which combined with the finite element model. The aerodynamic characteristics of the membrane rotor under hovering conditions are studied using fluid–structure interaction method. It is found that the calculation results matched well with the experiment results. The design of the structural parameters such as the membrane proportion, shape, and position of the membrane rotor is optimized. The influence of each parameter on the aerodynamic performance of the rotor is obtained. Under certain structural conditions, the performance can be effectively improved, which provides a new idea for the design of the nano rotor.

scholarly journals Design optimization of vehicle asynchronous motors based on fractional harmonic response analysis

2021 ◽  
Vol 12 (1) ◽  
pp. 689-700
Author(s):  
Ao Lei ◽  
Chuan-Xue Song ◽  
Yu-Long Lei ◽  
Yao Fu
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Natural Frequency ◽  
Asynchronous Motor ◽  
Element Model ◽  
Design Parameters ◽  
Response Analysis ◽  
Harmonic Response ◽  
First Order ◽  
Harmonic Response Analysis

Abstract. To make vehicles more reliable and efficient, many researchers have tried to improve the rotor performance. Although certain achievements have been made, the previous finite element model did not reflect the historical process of the motor rotor well, and the rigidity and mass in rotor optimization are less discussed together. This paper firstly introduces fractional order into a finite element model to conduct the harmonic response analysis. Then, we propose an optimal design framework of a rotor. In the framework, objective functions of rigidity and mass are defined, and the relationship between high rigidity and the first-order frequency is discussed. In order to find the optimal values, an accelerated optimization method based on response surface (ARSO) is proposed to find the suitable design parameters of rigidity and mass. Because the higher rigidity can be transformed into the first-order natural frequency by objective function, this paper analyzes the first-order frequency and mass of a motor rotor in the experiment. The results proved that not only is the fractional model effective, but also the ARSO can optimize the rotor structure. The first-order natural frequency of asynchronous motor rotor is increased by 11.2 %, and the mass is reduced by 13.8 %, which can realize high stiffness and light mass of asynchronous motor rotors.

An Effective Method for Determining Finite Element Model Parameters of Rotor Elastic Support System

2011 ◽  
Vol 141 ◽  
pp. 191-197
Author(s):  
Yong Xing Wang ◽  
Jiang Yan ◽  
Sheng Ze Wang
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Support System ◽  
Structural Parameters ◽  
Element Model ◽  
Elastic Support ◽  
Asymmetric Structure ◽  
Model Parameters ◽  
Equivalent Stiffness ◽  
Rolling Ball

A finite element model of the elastic support rotor system based on the corresponding experimental model was established. According to the principle of two types of model with an equal first order critical speed, the equivalent stiffness and damping of a rolling ball bearing support system with rubber rings determined by experiment were transferred into the finite element model. Then, the dynamic behavior of rotor systems with symmetric and asymmetric structure, different support system stiffness and support span were calculated and analyzed respectively. At last, the influence of the rotor structural parameters on the equivalent stiffness of elastic bearing support system obtained by experiment was pointed out.

Thermal-Mechanical Analysis of an NCA Type of Chip-on-Glass Assemblies

2000 ◽  
Author(s):  
Hsien-Chie Cheng ◽  
Ming-Hsiao Lee ◽  
Kuo-Ning Chiang ◽  
Chung-Wen Chang
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Contact Resistance ◽  
Contact Stress ◽  
Manufacturing Process ◽  
Element Model ◽  
Conductive Adhesive ◽  
Physical Contact ◽  
Design Parameters ◽  
Design Quality

Abstract Since the electrical conduction in the COG assembly using a non-conductive adhesive takes place through the connection of the bump and the electrodes, the contact resistance can be applied to the evaluation of the design quality as well as the overall reliability of the particular assembly. It should be further noted that as reported in the literature (e.g., see Liu, 1996; Kristiansen et al, 1998; Nicewarner, 1999; Timsit, 1999), the contact resistance between the bump and the electrode on the substrate strongly depends on the contact stress and the contact area. A higher reliability of the packaging somewhat relies on better contact stability as well as larger bonding stresses. In order to explore the physical contact behaviors of a non-conductive adhesive type of COG assemblies, the contact pressure during manufacturing process sequences and during the temperature variation are extensively investigated using a three-dimensional nonlinear finite element model. The so-called death-birth simulation technique is applied to model the manufacturing process sequences. The typical COG assemblies associated with two types of micro-bumps that are made of different materials: metal and composite are considered as the test vehicle. The contact stress between the electrode and the bump is extensively compared at each manufacturing sequence as well as at elevated temperature in order to investigate the corresponding mechanical interaction. Furthermore, the adhesion stresses of the adhesive are also evaluated to further investigate the possibilities of cracking or delamination within the adhesive and in its interfaces with the die and with the substrate. At last, a parametric finite element model is performed over number of geometry/material design parameters to investigate their impact on the contact/adhesion stresses so as to attain a better reliability design.

FEM Simulation of Anisotropic Parameters Influencing the Earing in Sheet Metal Deep Drawing Process

2011 ◽  
Vol 88-89 ◽  
pp. 638-641 ◽  
Author(s):  
Lei Chen
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Sheet Metal ◽  
Deep Drawing ◽  
Fem Simulation ◽  
Element Model ◽  
Drawing Process ◽  
Deep Drawing Process ◽  
Material Characteristics

Earing is often undesirable in the production of deep drawn containers because it results in a nonuniform cup height. A finite element model for earring analysis is developed considering only the flange area of the sheet. It was found that the draw-in depth of the flange increases with the increase of the r value, and it remains invariable when r value is larger than 2. With the increase of the r value, the max thickness decreases and the min thickness increases. If △r>0, four earings are formed. If △r =0, the material characteristics in all the planar directions are same. The flange uniformly flows into the die cavity, no earing is formed. If △r<0, four earings are formed. The earing distribution is dominated by r0, r45 and r90. Both r and △r have much effect on the earing distribution.

The Influence of Residual Stress on the Machining Deformation

2012 ◽  
Vol 426 ◽  
pp. 172-176
Author(s):  
Hun Guo
Keyword(s):  
Residual Stress ◽  
Finite Element ◽  
Finite Element Model ◽  
Simulation Model ◽  
Elasticity Theory ◽  
Initial Stress ◽  
Fem Simulation ◽  
Element Model ◽  
Fem Model ◽  
Simulation Results

The key problems in 2D FEM simulation such as the establishment of finite element model, the initial stress loading, the distortion appraisal are solved and 2D FEM simulation model is built to analyze the milling distortion caused by the residual stress. The FEM model is verified by the elasticity theory. Some machining cases are simulated by using of the FEM model. The machining distortion caused by residual stress are analyzed and summarized using the simulation results.

Sign in / Sign up

Export Citation Format

Share Document