ACTIVE VIBRATION PROTECTION BASED ON THE MECHATRONIC SYSTEM

Author(s):  
R.N. POLYAKOV ◽  
A.V. GORIN ◽  
R.K. ZARETSKIY ◽  
N.V. TOKMAKOV

The article examined and analyzed various types of vibration protection systems. Based on the results of the analysis, it was concluded that the known methods for providing vibration protection do not fully satisfy the requirements for them. Therefore, the possibility of using an active vibration protection system based on piezoelectric elements is considered. The design was developed and general ideas about the structure of the active vibration protection system, the principle of its operation were formulated.

Author(s):  
M.S. Korytov ◽  
◽  
V.S. Sherbakov ◽  
I.E. Pochekueva ◽  
◽  
...  

Vibrations of construction and road machinery components that occur during their operation are a harmful production factor for machine operators, therefore, their reduction can be considered a very urgent task. The main route of vibration transmission is through vibration isolation systems for the operator’s seat and cab. The easiest and most cost-effective way to isolate the operator from vibration is through his seat by reducing vibration. The simplest and most reliable vibration protection systems with one degree of freedom limited by vertical movements of the chair can be used for the chairs. Vibration protection mechanisms and systems with quasi-zero rigidity are considered promising. They provide constant static force over a certain range of movement of the object. The task of developing mathematical models describing vibration protection systems with quasi-zero rigidity is urgent. In the Matlab software package using the Simscape library for modeling physical elements, a simulation mathematical model of the vibration protection system of a chair with one degree of freedom has been developed. The base of the chair in the developed model performs harmonic sinusoidal movements. The output parameters of the developed mathematical model are the time dependences of the chair coordinates and accelerations. The blocks used in the model are described, the static force characteristics are given, given using the Hermite spline. The model includes a block of hard movement restrictions. An example of using the developed simulation mathematical model of the chair is given. The developed model makes it possible to specify both the dimensions of the quasi-zero stiffness section and the shape of the curves of the force static characteristics of the vibration protection system. It can be integrated into higher level models.


Author(s):  
B. Aparna ◽  
S. Madhavi ◽  
G. Mounika ◽  
P. Avinash ◽  
S. Chakravarthi

We propose a new design for large-scale multimedia content protection systems. Our design leverages cloud infrastructures to provide cost efficiency, rapid deployment, scalability, and elasticity to accommodate varying workloads. The proposed system can be used to protect different multimedia content types, including videos, images, audio clips, songs, and music clips. The system can be deployed on private and/or public clouds. Our system has two novel components: (i) method to create signatures of videos, and (ii) distributed matching engine for multimedia objects. The signature method creates robust and representative signatures of videos that capture the depth signals in these videos and it is computationally efficient to compute and compare as well as it requires small storage. The distributed matching engine achieves high scalability and it is designed to support different multimedia objects. We implemented the proposed system and deployed it on two clouds: Amazon cloud and our private cloud. Our experiments with more than 11,000 videos and 1 million images show the high accuracy and scalability of the proposed system. In addition, we compared our system to the protection system used by YouTube and our results show that the YouTube protection system fails to detect most copies of videos, while our system detects more than 98% of them.


The application of preparations of biological origin in the protection system of soybean grown under conditions of intensive irrigated crop rotations conforms to the modern tendencies of science and production development. The use of them contributes to solving ecological, production and social-economic problems. The study presents the three-year research on the efficiency of systems protecting soybean from pests and diseases based on biological and chemical preparations. The research was conducted in typical soil and climate conditions of the South of Ukraine. Zonal agricultural methods and generally accepted research methodology were used. The purpose of the research was to create a soybean protection system based on preparations of biological origin, ensuring high productivity of high-quality products reducing a negative impact of the crop production on the environment. The study emphasizes that, under irrigated conditions of the South of Ukraine, the application of biological preparations has a positive impact on the indexes of growth, development and formation of the elements of soybean yield structure. There was an increase in the crop biological weight by 13.8 % and 22.1 % and the number of seeds per plant rose by 11.6 and 14.6 % as a consequence of eliminating harmful organisms with the plant protection systems. The larger ground mass was formed by medium-ripe varieties Danai and Svyatogor, on which the increase from protection measures was higher. Weight 1000 pcs. the seeds did not undergo significant changes. It is established that the larger seeds were formed by Danaya and Svyatogor varieties, in which the average weight is 1000 pcs. seeds were 142 and 136 g, respectively, while in the variety Diona this figure was 133 g. There was an increase in the height of the lowest pod when the total plant height rose. For medium-ripe varieties was characterized by a higher attachment of beans, where the highest values of this indicator acquired in the variety Svyatogor. The medium maturing soybean variety Danaia formed the maximum yield of 3.23 and 3.35 t/ha respectively, when biological and chemical protection systems were applied. The research establishes that the application of the bio-fungicide Psevdobakterin 2 (2.0 l/ha) in the crop protection system at the beginning of soybean flowering and the bio-fungicide Baktofit (2.5 l/ha) with the bio-insecticide Lepidotsid-BTU (10.0 l/ha) at the beginning of pod formation does not reduce the productivity of the soybean varieties under study considerably, when compared to the application of chemical preparations. The research determines that the soybean protection system under study ensures a decrease in the coefficient of soybean water uptake by 7.2-13.0 %, increasing the total water intake to an inconsiderable degree. Biologization of the soybean crop protection system leads to a reduction in production costs compared to the chemical protection system. Taking into account the needs for the collection of additional products, costs increase by an average of 1 thousand UAH/ha, while for chemical protection systems by 1.8 thousand UAH/ha. At the same time, the cost is reduced by 220-360 UAH/t and the profitability of growing crops is increased by 3.8-7.8 %. There has been a reduction in the burden of pesticides on the environment and the production of cleaner products. This indicates the prospect of using the biofungicides Pseudobacterin 2 and Bactophyte and the bioinsecticide Lepidocid-BTU on soybeans to protect plants from pests.


Geosciences ◽  
2021 ◽  
Vol 11 (5) ◽  
pp. 197
Author(s):  
Axel Volkwein ◽  
Marcel Fulde ◽  
Ingvar Krieger Hauksson

Flexible rockfall protection systems are an effective and efficient remedy against rockfalls with energy levels between 100 and up to 10,000 kJ. Although they are heavily in use all around the world, the backgrounds that guarantee a reliable barrier are not well known by most of intervening agents and users. This contribution gives some insights on how to judge the capability, reliability, and trustworthiness of a rockfall protection system. The paper focuses on three strategies to build up confidence and trustworthiness regarding the barrier’s correct or expected functioning: testing, certification, and how to assess adaptions of standard barrier systems.


Author(s):  
V.P. Podchezertsev ◽  
S.V. Topilskaya

The article discusses criteria for selecting the vibration protection for the spacecraft inertial orientation system. The considered vibration protection system allows providing acceptable amplitude acceleration for the gyroscopic device sensitive elements under vibration impact on the device body during the spacecraft launching and high angular stability of the position of the sensitive elements relative to the inertial coordinate system during a long period of operation (15 years) in orbit. The proposed vibration protection system consists of shock absorbers (springs) with stable high elastic characteristics under all factors of operation in the outer space and dynamic vibration dampers. The article presents a method for determining the parameters of dynamic vibration dampers taking into account the characteristics of the shock absorber, critical for the damping system of an inertial device. The proposed method for adjusting dynamic vibration dampers consists in suppressing vibrations at the natural frequency f1 of the shock absorption system and providing acceptable values of the gain coefficients of the structure resonant vibration amplitudes near the natural frequency f1. Certain characteristics of the damping system allow realizing the permissible vibration amplification coefficients at resonance, without significantly affecting the level of vibration suppression in the natural frequency zone of the vibration protection object


Sign in / Sign up

Export Citation Format

Share Document