scholarly journals Design and Analysis of Efficient H-Shaped Multiband Antenna with DGS for Wireless Applications

2020 ◽  
Vol 9 (5) ◽  
pp. 2156-2157
Keyword(s):  
Patch Antenna ◽  
Low Cost ◽  
Impedance Matching ◽  
Ground Plane ◽  
Beam Width ◽  
Split Ring Resonator ◽  
Simulation Software ◽  
Defected Ground Structure ◽  
Multiband Antenna ◽  
Current Path

An efficient H-shaped micro strip multiband antenna is constructed and simulated with slot structure of Split Ring Resonator (SRR) in a ground plane as Defected Ground Structure (DGS) for high frequency applications is proposed. Micro Strip patch antenna is mostly preferred because of its very good radiation properties. Also it is the light weight and low cost device so its usage is very high and its fabrication method is very easy. DGS is used to alter the current path in the ground part of the patch antenna by making this it provides multiband support. The H shape patch antenna with the proper ground plane is normally chosen for increasing the bandwidth of the antenna by providing impedance matching and reduce loss. This type of antenna mostly used in where small size and broad beam width are required. In the simulation VSWR, radiation pattern, gain, return loss were measured using simulation software HFSS

scholarly journals A Novel Circular Slotted Microstrip-Fed Patch Antenna with three Triangle Shape Defected Ground Structure for Multiband Applications

2018 ◽  
Vol 7 (3) ◽  
pp. 56-63 ◽  
Author(s):  
A. Jaiswal ◽  
R. K. Sarin ◽  
B. Raj ◽  
S. Sukhija
Keyword(s):  
Patch Antenna ◽  
Return Loss ◽  
Impedance Matching ◽  
Ground Plane ◽  
Defected Ground Structure ◽  
Ground Structure ◽  
Resonant Frequencies ◽  
Wireless Applications ◽  
Rectangular Patch ◽  
Miniaturized Antenna

In this paper, a novel circular slotted rectangular patch antenna with three triangle shape Defected Ground Structure (DGS) has been proposed. Radiating patch is made by cutting circular slots of radius 3 mm from the three sides and center of the conventional rectangular patch structure and three triangle shape defects are presented on the ground layer. The size of the proposed antenna is 38 X 25 mm2. Optimization is performed and simulation results have been obtained using Empire XCcel 5.51 software. Thus, a miniaturized antenna is designed which has three impedance bandwidths of 0.957 GHz,  0.779 GHz, 0.665 GHz with resonant frequencies at 3.33 GHz, 6.97 GHz and 8.59 GHz and the corresponding return loss at the three resonant frequencies are -40 dB, -43 dB and -38.71 dB respectively. A prototype is also fabricated and tested. Fine agreement between the measured and simulated results has been obtained. It has been observed that introducing three triangle shape defects on the ground plane results in increased bandwidth, less return loss, good radiation pattern and better impedance matching over the required operating bands which can be used for wireless applications and future 5G applications.

Reduced Cross-Polarization Patch Antenna with Optimized Impedance Matching Using a Complimentary Split Ring Resonator and Slots as Defected Ground Structure

2021 ◽  
Vol 36 (6) ◽  
pp. 718-725
Author(s):  
Narayanasamy RajeshKumar ◽  
Palani Sathya ◽  
Sharul Rahim ◽  
Akaa Eteng
Keyword(s):  
Patch Antenna ◽  
Ring Resonator ◽  
Impedance Matching ◽  
Equivalent Circuit Model ◽  
Split Ring Resonator ◽  
Cross Polarization ◽  
Defected Ground Structure ◽  
Ground Structure ◽  
Split Ring ◽  
Surface Current Density

An innovative method is proposed to improve the cross-polarization performance and impedance matching of a microstrip antenna by integrating a complimentary split ring resonator and slots as a defected ground structure. An equivalent circuit model (ECM) enables the design take into consideration the mutual coupling between the antenna patch and the Defected Ground Structure. The input impedance and surface current density analysis confirms that the integration of a CSRR within a rectangular microstrip patch antenna leads to uniform comparative cross-polarization level below 40 dB in the H-plane, over an angular range of ± 50°. Introducing parallel slots, as well, leads to a reduction of spurious antenna radiation, thereby improving the impedance matching. Measurements conducted on a fabricated prototype are consistent with simulation results. The proposed antenna has a peak gain of 4.16 dB at 2.6 GHz resonating frequency, and hence is good candidate for broadband service applications.

scholarly journals A Pentagonal Shaped Microstrip Planar Antenna with Defected Ground Structure for Ultrawideband Applications

2021 ◽  
Author(s):  
Saida Ibnyaich ◽  
Samira Chabaa ◽  
Layla wakrim ◽  
Abdessalam El Yassini ◽  
Abdelouhab Zeroual ◽  
...  
Keyword(s):  
Patch Antenna ◽  
Impedance Matching ◽  
Ground Plane ◽  
Small Dimension ◽  
Impedance Bandwidth ◽  
Defected Ground Structure ◽  
Uwb Antenna ◽  
Large Bandwidth ◽  
Excellent Candidate ◽  
Radar Applications

Abstract A new compact pentagonal microstrip patch antenna with slotted ground plane structure, developed for use in ultrawideband applications, is studied in this article. The proposed antenna is mainly constituted by a pentagonal shaped patch antenna, a defected ground plane structure, two stubs, and four slots to improve the bandwidth. The designed antenna has an overall dimension of 30×17.59×1.6mm 3 , for WIMAX /WLAN/ WiFi/HIPERLAN-2 /Bluetooth /LTE /5G applications with a very large bandwidth starting from 2.66 GHz to 10.82 GHz (S 11 <-6 dB ). A parametric study of the ground plane structure was carried out to find the final and the optimal UWB antenna, and to confirm that the antenna has good performance and broader bandwidth. The proposed antenna prototype has been fabricated. The measured results indicate that the antenna has a good impedance matching. The antenna has an electrically small dimension with a good gain, a notable efficiency, and a wide impedance bandwidth, which makes this antenna an excellent candidate for ultrawideband wireless communication, microwave imaging, radar applications, and the major part of the mobile phone frequencies as well.

Miniaturized curved slotted patch antenna over a fractalized EBG ground plane

2016 ◽  
Vol 9 (3) ◽  
pp. 599-605 ◽  
Author(s):  
Saurabh Kumar ◽  
Dinesh Kumar Vishwakarma
Keyword(s):  
Patch Antenna ◽  
Communication Systems ◽  
Low Cost ◽  
Impedance Matching ◽  
Ground Plane ◽  
Microstrip Patch Antenna ◽  
Electromagnetic Bandgap ◽  
Microstrip Patch ◽  
Compact Size ◽  
Improved Performance

In this paper, a miniaturized coaxial feed curved-slotted microstrip patch antenna over a fractalized uniplanar compact electromagnetic bandgap (F-UC-EBG) ground plane is proposed and investigated. Compact size is achieved by cutting the curved slots along the orthogonal directions of the patch radiator. The curved-slotted microstrip patch antenna is 38.30% miniaturized as compared with the conventional microstrip patch antenna resonating at 2.38 GHz. Furthermore, the ordinary ground plane of the curved slotted patch antenna is replaced by the F-UC-EBG ground plane. Due to the slow wave phenomenon created in the F-UC-EBG structure and the better impedance matching at the lower frequency further miniaturization and improved performance are obtained. The proposed antenna shows 74.76% miniaturization as compared with the conventional microstrip patch antenna resonating at 1.57 GHz and has 2.61% 10-dB fractional bandwidth, 1.49 dB gain, and 81.59% radiation efficiency. The proposed antenna is fabricated on a low-cost FR4 substrate having an overall volume of 0.184λ0 × 0.184λ0 × 0.0236λ0 at 1.57 GHz GPS band. The measured and simulated results are in good agreement and predicting appropriateness of the antenna in portable and handheld communication systems for GPS applications.

scholarly journals A fractal quad-band antenna loaded with L-shaped slot and metamaterial for wireless applications

2018 ◽  
Vol 10 (7) ◽  
pp. 826-834 ◽  
Author(s):  
Tanweer Ali ◽  
Mohammad Saadh Aw ◽  
Rajashekhar C. Biradar
Keyword(s):  
Impedance Matching ◽  
Ground Plane ◽  
Surface Current ◽  
Split Ring Resonator ◽  
Wireless Applications ◽  
Sierpinski Triangle ◽  
Current Path ◽  
X Band ◽  
Compact Dimension ◽  
Novel Concept

A novel concept of using fractal antenna with metamaterial and slot to achieve multiband operation is investigated. The antenna consists of an L-shaped slot, Sierpinski triangle (used as fractal) as the radiating part and metamaterial circular split ring resonator (SRR) as the ground plane. The introduction of metamaterial in the ground plane makes the antenna operate at 3.3 GHz (middle WiMAX). The etching of Sierpinski triangle and L-shaped slot in the radiating monopole perturbs the surface current distribution; thereby increasing the total current path length which tends the antenna to further operate at 5.5 (upper WiMAX), 7.3 (satellite TV) and 9.9 GHz (X-band), respectively. The extraction of medium parameter of a circular SRR through waveguide medium is discussed in detail. The antenna has a compact dimension of 0.33λ0 × 0.27λ0 × 0.01λ0 = 30 mm × 24.8 mm × 1.6 mm, at a lower frequency of 3.3 GHz. Under simulation, antenna operates at 3.3, 5.5, 7.3 and 9.9 GHz with S11 < −10 dB bandwidth of about 5.9% (3.24–3.44 GHz), 5.6% (5.31–5.62 GHz), 7.3% (6.99–7.52 GHz) and 3.02% (9.78–10.08 GHz), respectively. In measurement, antenna exhibit resonances at 3.1, 5.52, 7.31, 9.72 GHz with S11 < −10 dB bandwidth of about 3.5% (3.04–3.15 GHz), 5.01% (5.44–5.72 GHz), 13.2% (6.76–7.72 GHz) and 5.77% (9.42–9.98 GHz), respectively. Good impedance matching and stable radiation characteristics are observed across the operational bandwidth of the proposed configuration.

scholarly journals Defected Ground Structure Based Two Element Microstrip Antenna Array with Reduced Mutual Coupling

2019 ◽  
Vol 8 (6S) ◽  
pp. 484-489 ◽  
Keyword(s):  
Antenna Array ◽  
Patch Antenna ◽  
Microstrip Antenna ◽  
Mutual Coupling ◽  
Ground Plane ◽  
Simulation Software ◽  
Defected Ground Structure ◽  
Ground Structure ◽  
Radiation Properties ◽  
Microstrip Antenna Array

In this paper two element microstrip antenna array with dumbbell shaped defected ground structure (DGS) is on reduction of mutual coupling is presented. The proposed of DGS antenna is simulated by an soft HFSS simulation software. this work is obtain a miniaturized microstrip patch antenna array using DGS for S Band is 2.2GHz.Initally the patch antenna array is designed at C band resonates at 5.2 GHz and the proposed of DGS is integrated in the ground plane of patch antenna for size reduction and this miniaturization is at cost of gain antenna and in order to improve the gain of miniaturized radiator. Patch radiator is further modified to radiation properties, so finally the resonance frequency of an initial microstrip antenna array shifts to 3.75 GHz to 7.15 GHz with the gain of 2.92 dB and its miniaturization performance is up to 63% and its conventional microstrip is successfully accomplished. The prototype antenna is fabricated with the FR-4 substrate and this technique is validate experimentally and measured results with good agreement as stimulated results.

scholarly journals A Terahertz CMOS V-Shaped Patch Antenna with Defected Ground Structure

Sensors ◽  
2018 ◽  
Vol 18 (8) ◽  
pp. 2432 ◽  
Author(s):  
Hyeongjin Kim ◽  
Wonseok Choe ◽  
Jinho Jeong
Keyword(s):  
Radiation Resistance ◽  
Patch Antenna ◽  
Impedance Matching ◽  
Ground Plane ◽  
Complementary Metal Oxide Semiconductor ◽  
Oxide Semiconductor ◽  
Cmos Process ◽  
Defected Ground Structure ◽  
Ground Structure ◽  
On Chip

In this paper, a V-shaped patch antenna with defected ground structure is proposed at terahertz to overcome the limited performance of a standard complementary metal-oxide semiconductor (CMOS) patch antenna consisting of several metal layers and very thin interdielectric layers. The proposed V-shaped patch with slots allows the increased radiation resistance and broadband performance. In addition, the patch resonating at different frequency from the V-shaped patch is stacked on the top to broaden the impedance-matching bandwidth. More importantly, the slots are formed in the ground plane, which is called the defected ground structure, to further increase the radiation resistance and thus improve the bandwidth and efficiency. It is verified from electromagnetic simulations that the leakage waves from the defected ground can enhance the antenna directivity and gain by coherently interfering with the topside radiation. The proposed on-chip antenna is fabricated using a standard 65 nm CMOS process. The on-wafer measurement shows very wide bandwidth in input reflection coefficient (<−10 dB), greater than 28.7% from 240 to >320 GHz. The measured peak gain was as high as 5.48 dBi at 295 GHz. To the best of the authors’ knowledge, these results belong to the best performance among the terahertz CMOS on-chip antennas without using additional components or processes such as dielectric resonators, lens, or substrate thinning.

scholarly journals Compact Uniplanar Multi Feed Multi Band ACS Monopole Antenna Loaded With Multiple Radiating Branches for Portable Wireless Devices

2018 ◽  
Vol 7 (2) ◽  
pp. 68-75 ◽  
Author(s):  
P. N. Vummadisetty ◽  
A. Kumar
Keyword(s):  
Low Cost ◽  
Impedance Matching ◽  
Ground Plane ◽  
Wireless Devices ◽  
Research Article ◽  
Resonant Modes ◽  
Wireless Device ◽  
Printed Monopole ◽  
5 Ghz ◽  
Multi Band

This research article presents, a compact 0.19 λ x 0.32 λ size ACS fed printed monopole wideband antenna loaded with multiple radiating branches suitable for LTE2300/WiBro, 5 GHz WLAN and WiMAX applications. The proposed triple band uniplanar antenna encompasses of C shaped strip, L shaped strip, rectangular shaped strip and a lateral ground plane. All the radiating strips and ground plane are etched on the 26 × 15 m size low cost FR4 epoxy substrate. This designed geometry evoked three independent reonances at 2.3 GHz, 3.5 GHz and 5.5 GHz with precise impedance matching over each operating band. The reflection coefficient ( ) response of the presented antenna demonstrates three distinct resonant modes associated with -10 dB bandwidths are about 2.24-2.40 GHz, 3.38-3.83 GHz and 5.0-6.25 GHz respectively. From the study, it is also observed that the proposed design works perfect with microstrip as well as CPW feedings. Hence the designed Multi Feed Multi Band (MFMB) antenna can be easily deployed in to any portable wireless device that works for 2.3/3.5/ 5 GHz frequency bands.

Dual-Band Proximity Coupled Feed Microstrip Patch Antenna with ‘T’ Slot on the Radiating Patch and ‘Dumbbell’ Shaped Defected Ground Structure

2016 ◽  
Vol 3 (2) ◽  
pp. 435 ◽  
Author(s):  
Dawit Fitsum ◽  
Dilip Mali ◽  
Mohammed Ismail
Keyword(s):  
Patch Antenna ◽  
Return Loss ◽  
Ground Plane ◽  
Microstrip Patch Antenna ◽  
Dual Band ◽  
Defected Ground Structure ◽  
Ground Structure ◽  
Wireless Applications ◽  
Microstrip Patch ◽  
Rectangular Microstrip Patch Antenna

<p>This paper presents Dual-Band proximity coupled feed rectangular Microstrip patch antenna with slots on the radiating patch and Defected Ground Structure. Initially a simple proximity coupled feed rectangular Microstrip patch antenna resonating at 2.4 GHz is designed. Etching out a ‘Dumbbell’ shaped defect from the ground plane and ‘T’ shaped slot from the radiating patch of the proximity coupled feed rectangular Microstrip patch antenna, results in a Dual-Band operation, i.e., resonating at 2.4 GHz and 4.5 GHz; with 30.3 % and 18.8% reduction in the overall area of the patch and the ground plane of the reference antenna respectively. The proposed antenna resonates in S-band at frequency of 2.4 GHz with bandwidth of 123.6 MHz and C-band at frequency of 4.5 GHz with bandwidth of 200 MHz, and a very good return loss of -22.1818 dB and -19.0839 dB at resonant frequency of 2.4 GHz and 4.5 GHz respectively is obtained. The proposed antenna is useful for different wireless applications in the S-band and C-band.</p>

Circularly Polarized Rectangular Microstrip Patch Antenna with Finite Ground Plane

2015 ◽  
Vol 4 (2) ◽  
pp. 74
Author(s):  
Sanyog Rawat ◽  
Kamlesh Kumar Sharma
Keyword(s):  
Patch Antenna ◽  
Return Loss ◽  
Ground Plane ◽  
Axial Ratio ◽  
Microstrip Patch Antenna ◽  
Simulation Software ◽  
Impedance Bandwidth ◽  
Circularly Polarized ◽  
Microstrip Patch ◽  
Rectangular Patch

<p class="Abstract"><span style="font-weight: normal;">In this paper a new geometry of patch antenna is proposed with improved bandwidth and circular polarization. The radiation performance of circularly polarized rectangular patch antenna is investigated by applying IE3D simulation software and its performance is compared with that of conventional rectangular patch antenna.</span> <span style="font-weight: normal;">Finite Ground truncation technique is used to obtain the desired results. The simulated return loss, axial ratio and smith chart with frequency for the proposed antenna is reported in this paper. It is shown that by selecting suitable ground-plane dimensions, air gap and location of the slits, the impedance bandwidth can be enhanced upto 10.15 % as compared to conventional rectangular patch (4.24%) with an axial ratio bandwidth of 4.05%.</span></p><p> </p><p> </p>

Sign in / Sign up

Export Citation Format

Share Document