scholarly journals A Small-Scale Experimental Investigation on the Benefits of a Hybrid Pile/Footing System on Sand

2021 ◽  
Vol 15 (2) ◽  
Author(s):  
Mohammed Maadheedi ◽  
Keyword(s):  
Experimental Investigation ◽  
Laboratory Tests ◽  
Steel Plate ◽  
Sustainable Design ◽  
Back Analysis ◽  
Ground Surface ◽  
The Other ◽  
Small Scale ◽  
Model Design ◽  
Hypothetical Scenario

This paper explores the capacity effects of a square steel plate welded at the ground surface on a driven open-ended steel pile (i.e. the plate would touch the ground surface after the pile achieves the required penetration). A series of strain-controlled, 1-g small-scale laboratory tests were undertaken on piles with and without a square steel plate attached. The piles were driven in dry, loosely packed, uniform sand. Two plates were used, one with a breadth equal to two times the diameter of the pile (2D) and the other with a breadth equal to three times the diameter of the piles (3D). A 20% increase in capacity was recorded for the 2D plate, and a 110% increase in capacity was recorded for the 3D plate when compared to the pile without an attached steel plate. The back-analysis of the results allowed the derivation of a new expression to calculate the capacity of bearing plates and plot its load-settlement profile, which accounted for the effects of sands compaction and dilation. By extrapolating the findings of these tests to a hypothetical scenario, a model design problem was described where the length of a pile can be reduced by 20% to 60% (depending on the load) by using a plate attached to the pile. The results of this study can help designers to minimise penetration depth; thus, achieving a more economical and sustainable design.

scholarly journals Confinement of Masonry Columns with the FRCM-System: Theoretical and Experimental Investigation

2020 ◽  
Vol 5 (11) ◽  
pp. 101
Author(s):  
Maria Antonietta Aiello ◽  
Alessio Cascardi ◽  
Luciano Ombres ◽  
Salvatore Verre
Keyword(s):  
Experimental Investigation ◽  
Stress Transfer ◽  
Experimental Results ◽  
The Other ◽  
Analytical Models ◽  
Small Scale ◽  
Structural Element ◽  
Technical Literature ◽  
Number Of Layers ◽  
Other Hand

Fabric Reinforced Cementitious Matrix (FRCM) systems are promising solutions for the confinement of masonry columns because they demonstrate strengthening effectiveness and, at the same time, compatibility with historical substrates. Nevertheless, the matrix is responsible for the stress-transfer from the structural element to the fabric-reinforcement. Therefore, in the case of poor-quality mortar, the effectiveness of the strengthening can be limited or even compromised. On the other hand, the low content of fibers utilized for FRCM systems generally involves the need to apply more layers in order to accomplish design requirements and a continuous configuration of the reinforcement is more often addressed. Few experimental and theoretical investigations have been targeted to the before mentioned aspects in the recent past, namely the influence of the kind of mortar, the number of layers, and the strengthening configuration (continuous, discontinuous) on the effectiveness of confinement. The present paper refers to the results of an experimental investigation on FRCM confined clay brick masonry. A series of small-scale masonry columns were tested under monotonic centered load until collapse. The varied parameters were the number of confining layers (i.e., 1, 2, and 3) and the confinement configuration (i.e., continuous and discontinuous). The performed research aims to contribute in strengthening to the knowledge in the field of FRCM-confinement, mainly focusing on some of the mentioned unexplored aspects (number of layers, strengthening configuration) that could be considered for validation/improvement of analytical design-oriented formulas. In particular, some analytical models, available in the technical literature, were adopted for predicting the herein reported experimental results. Even if based on few experimental results, the outcomes showed that the number of FRCM-layers and the confinement configuration were crucial parameters affecting the confining effectiveness. The compressive strength was satisfactorily predicted in all cases by the two available utilized models. On the other hand, an improvement in the utilized AOM model is suggested in order to include the stress–strain curves of the hardening type.

An Experimental Investigation Into the Pull-Out Capacity of Suction Caissons in Sand

2011 ◽  
Author(s):  
Siamak Kakasoltani ◽  
Mostafa Zeinoddini ◽  
Mahmoud R. Abdi ◽  
Hamid Arabzadeh
Keyword(s):  
Experimental Investigation ◽  
The Other ◽  
Silty Sand ◽  
Small Scale ◽  
Soil Density ◽  
Pull Out ◽  
Aspect Ratios ◽  
Rate Effects ◽  
Wall Slope ◽  
Suction Caissons

The pull-out performance of conventional suction caissons (with upright walls) has been previously investigated by a number of researchers. However, less attention has been formerly paid to tapered suction caissons. This paper reports some results from an experimental investigation into the pull-out performance of tapered suction caissons. The 1g experiments have been carried out on eight small scale suction caissons. Four specimens have had upright walls while the other four had a positive wall slope of 10%. The caissons have been installed in a soil tank containing very fine saturated silty sand. The caissons have then been subjected to vertical pull-out loads with different speeds. The effects of variations in soil density and pull-out rate on the pull-out capacities have also been investigated. In general, tapered caissons have been noticed to present enhanced pull-out capacities as compared to those from their equivalent upright caissons. The enhancement rate has been found to be more significant in suction caissons with higher aspect ratios. With both upright and tapered caissons the pull-out capacity increases by an increase in the pull-out rate. The pull-out rate effects are more significant with upright caissons in comparison to the corresponding tapered caissons. The density effects, however, are more significant with tapered caissons as compared to their equivalent upright caissons.

Experimental Investigation on the Failure Mechanism of Grooved Steel Plate Impacted by Projectile with Different Nose Shapes

2020 ◽  
Vol 846 ◽  
pp. 162-166
Author(s):  
Nan Zhou ◽  
Jin Xiang Wang ◽  
Zong Bao Tong ◽  
Song Ze Tang
Keyword(s):  
Experimental Investigation ◽  
Failure Mechanism ◽  
Steel Plate ◽  
Tensile Deformation ◽  
Metal Plate ◽  
The Other ◽  
Penetration Process ◽  
Erosion Damage ◽  
Ballistic Experiment ◽  
Nose Shape

In order to study the penetration performance of the tandem warhead composed of a front circular shaped charge and a rear penetration projectile, a grooved steel plate was processed to simulate the effect of circular shaped jets on metal plate, then the failure mechanism of the grooved steel plate impacted by rear projectile was investigated by ballistic experiment, meanwhile, the effect of projectile nose shape on the failure mechanism was also analyzed. The results show that the main failure mechanism of grooved steel plate is ductile tensile deformation or damage when the projectile impacted on the inner plate body and the depth of the pre-splitting groove is not big enough (usually more than 4mm), on the other hand, the circumferential sheared fracture of the bottom of the groove occurred when the depth of the pre-splitting groove is not less than 4mm. The oval projectile body has much greater erosion damage than rod-shaped projectile during the penetration process.

The Reliability of Retrieval-Induced Forgetting

2012 ◽  
Vol 17 (1) ◽  
pp. 1-10 ◽  
Author(s):  
Rosalind Potts ◽  
Robin Law ◽  
John F. Golding ◽  
David Groome
Keyword(s):  
Individual Differences ◽  
Recognition Test ◽  
Laboratory Tests ◽  
The Other ◽  
Clinical Factors ◽  
Test Items ◽  
T1 And T2 ◽  
Test Materials ◽  
Induced Forgetting

Retrieval-induced forgetting (RIF) refers to the finding that the retrieval of an item from memory impairs the retrieval of related items. The extent to which this impairment is found in laboratory tests varies between individuals, and recent studies have reported an association between individual differences in the strength of the RIF effect and other cognitive and clinical factors. The present study investigated the reliability of these individual differences in the RIF effect. A RIF task was administered to the same individuals on two occasions (sessions T1 and T2), one week apart. For Experiments 1 and 2 the final retrieval test at each session made use of a category-cue procedure, whereas Experiment 3 employed category-plus-letter cues, and Experiment 4 used a recognition test. In Experiment 2 the same test items that were studied, practiced, and tested at T1 were also studied, practiced, and tested at T2, but for the remaining three experiments two different item sets were used at T1 and T2. A significant RIF effect was found in all four experiments. A significant correlation was found between RIF scores at T1 and T2 in Experiment 2, but for the other three experiments the correlations between RIF scores at T1 and T2 failed to reach significance. This study therefore failed to find clear evidence for reliable individual differences in RIF performance, except where the same test materials were used for both test sessions. These findings have important implications for studies involving individual differences in RIF performance.

Platelet Suruival and Function in Rats with Enhanced Thrombotic Tendency

1985 ◽  
Vol 54 (04) ◽  
pp. 739-743 ◽  
Author(s):  
Federica Delaini ◽  
Elisabetta Dejana ◽  
Ine Reyers ◽  
Elisa Vicenzi ◽  
Germana De Bellis Vitti ◽  
...  
Keyword(s):  
Arachidonic Acid ◽  
Nephrotic Syndrome ◽  
Platelet Function ◽  
Laboratory Tests ◽  
Thrombus Formation ◽  
The Other ◽  
Mean Survival Time ◽  
The Mean ◽  
And Function ◽  
Thrombotic Tendency

SummaryWe have investigated the relevance of some laboratory tests of platelet function in predicting conditions of thrombotic tendency. For this purpose, we studied platelet survival, platelet aggregation in response to different stimuli, TxB2 and 6-keto-PGFlα production in serum of rats bearing a nephrotic syndrome induced by adriamycin. These animals show a heavy predisposition to the development of both arterial and venous thrombosis. The mean survival time was normal in nephrotic rats in comparison to controls. As to aggregation tests, a lower aggregating response was found in ADR-treated rats using ADP or collagen as stimulating agents. With arachidonic acid (AA) we observed similar aggregating responses at lower A A concentrations, whereas at higher AA concentrations a significantly lower response was found in nephrotic rats, despite their higher TxB2 production. Also TxB2 and 6-keto-PGFlα levels in serum of nephrotic rats were significantly higher than in controls. No consistent differences were found in PGI2-activity generated by vessels of control or nephrotic rats.These data show that platelet function may appear normal or even impaired in rats with a markedly increased thrombotic tendency. On the other hand, the significance of high TxB2 levels in connection with mechanisms leading to thrombus formation remains a controversial issue.

Experimental Investigation of aluminum doping crumb rubber/epoxy composite in reciprocating motion

2015 ◽  
Vol 3 ◽  
pp. 1
Author(s):  
Goutam Chandra Karar ◽  
Nipu Modak
Keyword(s):  
Experimental Investigation ◽  
Coefficient Of Friction ◽  
Epoxy Composite ◽  
Normal Load ◽  
Crumb Rubber ◽  
The Other ◽  
Reciprocating Motion ◽  
Molding Process ◽  
Friction Tester ◽  
The Coefficient Of Friction

The experimental investigation of reciprocating motion between the aluminum doped crumb rubber /epoxy composite and the steel ball has been carried out under Reciprocating Friction Tester, TR-282 to study the wear and coefficient of frictions using different normal loads (0.4Kg, 0.7Kgand1Kg), differentfrequencies (10Hz, 25Hz and 40Hz).The wear is a function of normal load, reciprocating frequency, reciprocating duration and the composition of the material. The percentage of aluminum presents in the composite changesbut the other components remain the same.The four types of composites are fabricated by compression molding process having 0%, 10%, 20% and 30% Al. The effect of different parameters such as normal load, reciprocating frequency and percentage of aluminum has been studied. It is observed that the wear and coefficient of friction is influenced by the parameters. The tendency of wear goes on decreasing with the increase of normal load and it is minimum for a composite having 10%aluminum at a normal load of 0.7Kg and then goes on increasing at higher loads for all types of composite due to the adhesive nature of the composite. The coefficient of friction goes on decreasing with increasing normal loads due to the formation of thin film as an effect of heat generation with normal load.

scholarly journals Black Hole Algorithm for Sustainable Design of Counterfort Retaining Walls

2020 ◽  
Vol 12 (7) ◽  
pp. 2767 ◽  
Author(s):  
Víctor Yepes ◽  
José V. Martí ◽  
José García
Keyword(s):  
Black Hole ◽  
Sustainable Design ◽  
Retaining Walls ◽  
The Other ◽  
Trade Off ◽  
Construction Company ◽  
Geometric Variables ◽  
The Stability ◽  
The Cost ◽  
Black Hole Algorithm

The optimization of the cost and CO 2 emissions in earth-retaining walls is of relevance, since these structures are often used in civil engineering. The optimization of costs is essential for the competitiveness of the construction company, and the optimization of emissions is relevant in the environmental impact of construction. To address the optimization, black hole metaheuristics were used, along with a discretization mechanism based on min–max normalization. The stability of the algorithm was evaluated with respect to the solutions obtained; the steel and concrete values obtained in both optimizations were analyzed. Additionally, the geometric variables of the structure were compared. Finally, the results obtained were compared with another algorithm that solved the problem. The results show that there is a trade-off between the use of steel and concrete. The solutions that minimize CO 2 emissions prefer the use of concrete instead of those that optimize the cost. On the other hand, when comparing the geometric variables, it is seen that most remain similar in both optimizations except for the distance between buttresses. When comparing with another algorithm, the results show a good performance in optimization using the black hole algorithm.

scholarly journals Analysis of Operational Efficiencies and Costs for Extracting Thinned Woods in Small-Scale Forestry, Nasunogahara Area, Tochigi Prefecture, Japan

2020 ◽  
Vol 3 (1) ◽  
pp. 61
Author(s):  
Kazuhiro Aruga
Keyword(s):  
Transportation Costs ◽  
The Other ◽  
Small Scale ◽  
Light Truck ◽  
Operation Costs ◽  
Other Hand ◽  
Light Trucks ◽  
The Cost ◽  
Manual Extraction ◽  
Truck Transportation

In this study, two operational methodologies to extract thinned woods were investigated in the Nasunogahara area, Tochigi Prefecture, Japan. Methodology one included manual extraction and light truck transportation. Methodology two included mini-forwarder forwarding and four-ton truck transportation. Furthermore, a newly introduced chipper was investigated. As a result, costs of manual extractions within 10 m and 20 m were JPY942/m3 and JPY1040/m3, respectively. On the other hand, the forwarding cost of the mini-forwarder was JPY499/m3, which was significantly lower than the cost of manual extractions. Transportation costs with light trucks and four-ton trucks were JPY7224/m3 and JPY1298/m3, respectively, with 28 km transportation distances. Chipping operation costs were JPY1036/m3 and JPY1160/m3 with three and two persons, respectively. Finally, the total costs of methodologies one and two from extraction within 20 m to chipping were estimated as JPY9300/m3 and JPY2833/m3, respectively, with 28 km transportation distances and three-person chipping operations (EUR1 = JPY126, as of 12 August 2020).

scholarly journals Does the visual salience of credit card features affect choice?

2021 ◽  
pp. 1-18
Author(s):  
Matthew D. Hilchey ◽  
Matthew Osborne ◽  
Dilip Soman
Keyword(s):  
Interest Rates ◽  
Random Sample ◽  
Credit Card ◽  
Credit Cards ◽  
Salient Feature ◽  
The Other ◽  
Visual Salience ◽  
Product Features ◽  
Hypothetical Scenario

Abstract Regulators require lenders to display a subset of credit card features in summary tables before customers finalize a credit card choice. Some jurisdictions require some features to be displayed more prominently than others to help ensure that consumers are made aware of them. This approach could lead to untoward effects on choice, such that relevant but nonprominent product features do not factor in as significantly. To test this possibility, we instructed a random sample of 1615 adults to choose between two hypothetical credit cards whose features were shown side by side in tables. The sample was instructed to select the card that would result in the lowest financial charges, given a hypothetical scenario. Critically, we randomly varied whether the annual interest rates and fees were made visually salient by making one, both, or neither brighter than other features. The findings show that even among credit-savvy individuals, choice tends strongly toward the product that outperforms the other on a salient feature. As a result, we encourage regulators to consider not only whether a key feature should be made more salient, but also the guidelines regarding when a key feature should be displayed prominently during credit card acquisition.

Sign in / Sign up

Export Citation Format

Share Document