Сrystalline structure and dielectric properties of ceramic materials based on AgNbO3

2020 ◽  
Vol 63 (7) ◽  
pp. 75-78
Author(s):  
Polina A. Bezborodova ◽  
◽  
Elena M. Filonenko ◽  
Kseniya R. Erager ◽  
Anatoly V. Butakov ◽  
...  
Keyword(s):  
Rietveld Method ◽  
Average Particle Size ◽  
Ceramic Materials ◽  
Analysis Data ◽  
Molar Ratio ◽  
Average Particle ◽  
Dielectric Parameters ◽  
Low Frequencies ◽  
X Ray ◽  
Substitution Degree

Using the data of qualitative X-ray phase analysis, it was shown that in a wide concentration range at 1223 K compounds based on silver niobate are formed in the condition of the heterovalent substitution of tungsten(VI) ions for niobium(V) ions. These compounds are isomorphic to a perovskite-type structure. Microprobe analysis data allows to determine the homogeneity of the analyzed samples and the correspondence of their experimental compositions to the theoretical ones for the formula Ag1-xNb1-xWxO3. Using the data of X-ray diffraction analysis (Rietveld method) in the Crystallography Data Analysis Software – GSAS, the crystal structure of the obtained compounds was refined. The surface morphology of samples having been obtained at 1373 K was investigated by scanning electron microscopy (SEM). It was shown that with an increase of Nb5+ to W6+ substitution degree for Ag1-xNb1-xWxO3 ceramic samples in the range of the (0.2≤x≤0.8) molar ratio, the average particle size for the studied compositions grows from 1.3 to 5.2 μm, respectively. For the obtained ceramic compounds based on silver niobate with a perovskite-like structure (tetragonal distortion), the temperature-frequency dependences of dielectric parameters in the range 300-900 K were studied. It was found that samples slowly cooled from 1373 K are characterized by low values of (ε ~ 10) and loss (tgδ ~ 0.004 at f = 1 kHz) at room temperature. The ceramics obtained are characterized by relatively high values of dielectric permittivity ε at low frequencies and/or high temperatures. The dielectric parameters of the obtained ceramics are similar to the characteristics of so-called "colossal" dielectric constant materials. The revealed features of the dielectric characteristics of quenched ceramics apparently result from Maxwell-Wagner relaxation at intercrystalline contacts.

Synthesis of Fe2O3/C Nanocomposite Using Microwave Assisted Calcination Method

2014 ◽  
Vol 896 ◽  
pp. 100-103 ◽  
Author(s):  
Anggi Puspita Swardhani ◽  
Ferry Iskandar ◽  
Abdullah Mikrajuddin ◽  
Khairurrijal
Keyword(s):  
Crystallite Size ◽  
Average Particle Size ◽  
Molar Ratio ◽  
Average Particle ◽  
X Ray ◽  
Molar Ratios ◽  
Microwave Assisted ◽  
Chloride Hexahydrate ◽  
Calcination Method ◽  
Scherrer Method

Fe2O3/C nanocomposites were successfully synthesized using microwave assisted calcination method. Ferric (III) chloride hexahydrate (FeCl36H2O), sodium hydroxide (NaOH), and dextrose monohydrate (C6H12O6H2O) were used as precursors. A microwave oven of 2.445 GHz with a power of 600 W for 20 minutes was employed during the syntheses. Calcination was performed in a simple furnace at 350 °C for 30 min. The molar ratio of C:Fe is the only process parameter. From Scanning Electron Microscope images, the average particle size were 199 nm and 74 nm for the samples with molar ratio of C:Fe of 1:2 and 1:1, respectively. X-ray diffractometer spectra showed that the obtained samples have γ-Fe2O3 (maghemite) crystal structure. Using the Scherrer method, the crystallite size were 61.7, 58.8, 52.5, and 48.8 nm for the samples with the molar ratios of C:Fe of 1:3, 1:2, 1:1, and 2:1, respectively. It means that the crystallite size of the nanocomposite decreases with the increase of the molar ratio of carbon to iron (C:Fe). The Brunauer-Emmett-Teller characterization showed that the surface area as high as 255.6 m2/g is achieved by of the Fe2O3/C nanocomposite with the molar ratio of C:Fe of 1:1.

scholarly journals In-flight Synthesis of Nanosized ZrC Particles from Various Precursors in RF Thermal Plasma

2021 ◽  
Author(s):  
Alejandro Martiz ◽  
Zoltán Károly ◽  
Eszter Bódis ◽  
Péter Fazekas ◽  
Miklós Mohai ◽  
...  
Keyword(s):  
Thermal Plasma ◽  
Photoelectron Spectroscopy ◽  
Average Particle Size ◽  
Reaction System ◽  
Spherical Shape ◽  
Molar Ratio ◽  
Average Particle ◽  
X Ray ◽  
Temperature Range ◽  
Rf Thermal Plasma

Synthesis of zirconium carbide (ZrC) powder was investigated applying a non-conventional atmospheric radiofrequency (RF) thermal plasma process. In one case, zirconium dioxide (ZrO2) was reacted with solid carbon or with methane with varying molar ratio. In the other, zirconium-propoxide (NZP), containing both constituents, was thermally decomposed in the Ar plasma. Temperature-dependent thermodynamic analysis was performed in the 500-5500 K temperature range to estimate the formation of possible equilibrium products for each reaction stoichiometry. Broad temperature range exists for the stability of solid ZrC for each explored reaction system. In accordance with this prediction, X-ray diffraction studies detected the ZrC as the major phase in all the prepared powders. The yield of particular runs ranged from 39 % to 98 %. Practically, full conversion was typical for the case of NZP precursor, however only partial conversion could be detected in ZrO2 reactions. The average particle size of the powders falls between 10 nm and 100 nm depending on the type of the reaction systems (either calculated from the specific surface area or derived from broadening the XRD reflections). The transmission electron micrographs indicated mostly globular shape of the nanosize particles. Quantitative analysis of the surface of the powders by X-ray photoelectron spectroscopy revealed the presence of oxygen and carbon. Evaluating the spectra of the powders prepared from NZP, and taking in the account its spherical shape, a ZrC core covered by a very thin (≈1.0 nm) ZrO2 layer may be accounted for the measured oxygen and a thicker carbonaceous layer.

Study on Hydrothermal Synthesis of Flower-Sphere MoS2

2011 ◽  
Vol 311-313 ◽  
pp. 566-570
Author(s):  
Jun Zhou ◽  
Xin Zhe Lan ◽  
Ping Ren ◽  
Lei Wu
Keyword(s):  
Reaction Time ◽  
Aging Time ◽  
Self Assembly ◽  
Average Particle Size ◽  
Molar Ratio ◽  
Average Particle ◽  
X Ray Diffraction ◽  
X Ray ◽  
Synthesis Conditions ◽  
Effective Technology

An effective technology of hydrothermal synthesizing flower-sphere MoS2 by reaction of Na2MoO4 and CS(NH2)2 with NH2OH•HCl as reductant was researched. The effect of the molar ratio of Mo to S, reaction temperature, reaction time, aging time on the yield, purity and morphology of the product was explored by means of X-ray diffraction (XRD) and scanning electron microscope (SEM). The results show that the optimal synthesis conditions are as follows: the molar ratio of Mo to S of 1:7, the temperature of 220°C, the reaction time of 24h and the aging time of 16h. Under these conditions, the inerratic and pure flower-sphere MoS2 was obtained. Its average particle size is about 2μm and the petal is self-assembly growth. The yield of the product can reach 88%.

STRUCTURAL AND MAGNETIC PROPERTIES OF HEMATITE NANOCRYSTALLINE OBTAINED BY BALL MILLING

2009 ◽  
Vol 08 (03) ◽  
pp. 267-272 ◽  
Author(s):  
O. M. LEMINE ◽  
R. MSALAM ◽  
A. ALYAMANI ◽  
M. SAJIEDDINE ◽  
S. MUFTI ◽  
...  
Keyword(s):  
Rietveld Method ◽  
Magnetic Hysteresis ◽  
Average Particle Size ◽  
Hysteresis Loops ◽  
Average Particle ◽  
Vibrating Sample Magnetometer ◽  
X Ray ◽  
Qualitative And Quantitative ◽  
Magnetic Hysteresis Loops ◽  
Structural And Magnetic Properties

α-Fe2O3 nanoparticles were obtained by a mechanical alloying of micrometer-sized powder at different milling times. Samples were characterized by X-ray powder diffraction, scanning electron microscope (SEM), Mössbauer spectrometry, and vibrating sample magnetometer (VSM). A qualitative and quantitative phase analyses using the Rietveld method have been performed based on the XRD data. The results did not reveal any phase change during the milling. The average particle size decreases with a prolongation of milling times, while the lattice parameters, unit cell volume, and microstrain increase. Mössbauer measurement shows that there are two components, one nanometric and other micrometric. The magnetic hysteresis loops shows that the samples are typical of ferromagnet with superparamagnetic fraction in the material.

Modified Polyol-Mediated Synthesis of Doped TiO2 Nanoparticles as the Photoanode in Dye Solar Cells (DSCs)

2014 ◽  
Vol 925 ◽  
pp. 575-579
Author(s):  
Sattar Bashardoust ◽  
Muti Mohamed Norani ◽  
Boon Hoong Ong ◽  
Siti Nur Azella Zaine
Keyword(s):  
Crystal Structure ◽  
Solar Cells ◽  
Lattice Structure ◽  
Average Particle Size ◽  
Spherical Particles ◽  
Hydroxyl Group ◽  
Molar Ratio ◽  
Average Particle ◽  
X Ray ◽  
Dye Solar Cells

Synthesis of nanoscale TiO2exhibiting specific properties of electron or ion conductivity is critical to improve the performance of dye solar cells (DSC). This paper presents the modified polyol-mediated synthesis of doped TiO2nanoparticles. TiO2samples were doped with cobalt (Co) and nickel (Ni) and the effects of calcination temperature (550 °C and 650 °C) on the crystallinity of pure samples were investigated. X-ray diffraction (XRD) analysis was used to determine the effect of dopant in lattice structure. The morphology and Crystal structure of TiO2samples and their chemical analysis was conducted using scanning electron microscopy (SEM) and energy dispersive X-ray (EDX) spectrometer respectively. Results show agglomeration of spherical particles in all doped samples. Crystal structure in the doped samples reveals modified phases and major crystal phase identical to anatase. It is observed that the molar ratio of water to metal can control the nucleation and growth and prevents significant agglomeration of nanoparticles. More effective doping was recorded for samples with 0.5 % concentration. Effective hydroxyl group is detected in both 0.5% Ni and Co promising good photocatalytic material. SEM images of 0.2% Ni-doped sample shows smallest average particle size.

scholarly journals Thermal, Structural, and Physical Properties of Freeze Dried Tropical Fruit Powder

2014 ◽  
Vol 2014 ◽  
pp. 1-10 ◽  
Author(s):  
K. A. Athmaselvi ◽  
C. Kumar ◽  
M. Balasubramanian ◽  
Ishita Roy
Keyword(s):  
Particle Size ◽  
Physical Properties ◽  
Average Particle Size ◽  
Average Particle ◽  
X Ray Diffraction ◽  
Tropical Fruit ◽  
X Ray ◽  
Freeze Dried ◽  
Fruit Powder ◽  
Lcr Meter

This study evaluates the physical properties of freeze dried tropical (guava, sapota, and papaya) fruit powders. Thermal stability and weight loss were evaluated using TGA-DSC and IR, which showed pectin as the main solid constituent. LCR meter measured electrical conductivity, dielectric constant, and dielectric loss factor. Functional groups assessed by FTIR showed presence of chlorides, and O–H and N–H bonds in guava, chloride and C–H bond in papaya, and chlorides, and C=O and C–H bonds in sapota. Particle size and type of starch were evaluated by X-ray diffraction and microstructure through scanning electronic microscopy. A semicrystalline profile and average particle size of the fruit powders were evidenced by X-ray diffraction and lamellar/spherical morphologies by SEM. Presence of A-type starch was observed in all three fruits. Dependence of electric and dielectric properties on frequency and temperature was observed.

Fabrication of monoclinic BiVO4 photocatalyst film and its photocatalytic activity for organic pollutant removal

2021 ◽  
Vol 0 (0) ◽  
Author(s):  
Saranyoo Chaiwichian ◽  
Buagun Samran
Keyword(s):  
Visible Light ◽  
Visible Light Irradiation ◽  
Average Particle Size ◽  
Pollutant Removal ◽  
Light Irradiation ◽  
Average Particle ◽  
Film Sample ◽  
Acid Orange 7 ◽  
Acid Orange ◽  
X Ray

Abstract Monoclinic BiVO4 photocatalyst films decorated on glass substrates were successfully fabricated via a dip-coating technique with different annealing temperatures of 400 °C, 450 °C, 500°C, and 550 °C. All of the physical and chemical properties of as-prepared BiVO4 photocatalyst film samples were investigated using X-ray diffraction, scanning electron microscopy, X-ray photoelectron spectroscopy and UV–vis diffuse reflectance spectra techniques. The results revealed that the as-prepared BiVO4 photocatalyst film samples retained a monoclinic phase with an average particle size of about 50 – 100 nm. Moreover, the BiVO4 photocatalyst film samples showed a strong photoabsorption edge in the range of visible light with the band gap energy of 2.46 eV. The photocatalytic activities of all the film samples were tested by the degradation of model acid orange 7 under visible light irradiation. The BiVO4 photocatalyst film sample annealed at a temperature of 500 °C showed the highest photoactivity efficiency compared with other film samples, reaching up to 51%within 180 min. In addition, the stability and reusability of BiVO4 photocatalyst film sample made with an annealing temperature of 500 °C did not show loss of photodegradation efficiency of acid orange 7 after ten recycles. A likely mechanism of the photocatalytic process was established by trapping experiments, indicating that the hydroxyl radical scavenger species can be considered to play a key role for acid orange 7 degradation under visible light irradiation.

Nanocrystalline α-Fe2O3: A Superparamagnetic Material for w-LED Application and Waste Water Treatment

2021 ◽  
Author(s):  
Mahesh Gaidhane ◽  
Deepak Taikar ◽  
Pravin Gaidhane ◽  
Kalpana Nagde
Keyword(s):  
Photocatalytic Activity ◽  
Waste Water Treatment ◽  
Sol Gel ◽  
Average Particle Size ◽  
Emission Spectra ◽  
Broad Emission Band ◽  
Average Particle ◽  
X Ray ◽  
Prepared Material ◽  
Cie Chromaticity

Abstract Nanocrystalline α-Fe2O3 is synthesized by sol-gel technique. The prepared nanomaterial was characterized by X-ray diffraction (XRD), SEM, TEM, Fourier Transform Infrared (FTIR) spectroscopy, Vibrating Sample Magnetometry (VSM) and photoluminescence (PL) techniques. X-ray powder diffraction analysis confirmed the formation of α-Fe2O3. Electron microscopy showed spherical morphologies with an average particle size of 30-40 nm. The magnetic property of the prepared material was studied by VSM at room temperature. VSM study shows superparamagnetic nature of the synthesized nanoparticles. Photoluminescence (PL) emission spectra show intense broad emission band centered at 570 nm with 393 nm excitation indicating its usefulness for w-LED application. The CIE-chromaticity color coordinates of prepared material were calculated. The photocatalytic activity of the α-Fe2O3 nanoparticles was analyzed and the nanopowder exhibited good photocatalytic activity for the removal AO7 from its aqueous solution.

scholarly journals Synthesis of cuprous oxide nanocubes combined with chitosan nanoparticles and its application to p-nitrophenol degradation

2021 ◽  
Vol 22 (48) ◽  
Author(s):  
Tran Thi Bich Quyen ◽  
Ngo Nguyen Tra My ◽  
Do Thi Thuy Ngan ◽  
Duy Toan Pham ◽  
Doan Van Hong Thien
Keyword(s):  
Photocatalytic Activity ◽  
Cuprous Oxide ◽  
Treatment Time ◽  
Average Particle Size ◽  
Chitosan Nanoparticles ◽  
Synthetic Approach ◽  
Average Particle ◽  
X Ray ◽  
Nitrophenol Reduction ◽  
Nitrophenol Degradation

For the first time, cuprous oxide nanocubes (Cu2O NCBs) were successfully combined with chitosan nanoparticles (CS NPs) to generate Cu2O NCBs/CS NPs composites material with highly optical property and photocatalytic activity using a simple and eco-friendly synthetic approach at room temperature for 30 min. The synthesized Cu2O NCBs NPs/CS NPs were determined characterizations by Ultraviolet-visible spectroscopy (UV-vis), Fourier transform infrared spectroscopy (FTIR), X – ray Diffraction (XRD),  Transmission Electron Microscope (TEM) and Energy-dispersive X-ray spectroscopy (EDX). Results show that the Cu2O NCBs/CS NPs composites have an average particle size of ~3-5 nm; in which, Cu2O has the form of nanocubes (Cu2O NCBs) with size ~3-4 nm and chitosan nanoparticles with spherical shape (CS NPs) with size ~4-5 nm. In addition, the percent (%) composition of elements present in Cu2O NCBs/CS NPs composites material have been obtained respective: Cu (23.99%), O (38.18%), and C (33.61%). Moreover, Cu2O NCBs/CS NPs composites material was also investigated for photocatalytic activity applied in p-nitrophenol degradation. The obtained results showed that the catalytic capability of Cu2O NCBs/CS NPs for p-nitrophenol reduction reached the highest efficiency >55% in the treatment time of 25 min, and this efficiency was higher than that result of using ZnO@chitosan nanoparticles (ZnO@CS NPs) catalyst under the same conditions for comparison.

Sign in / Sign up

Export Citation Format

Share Document