Limb and thoracolumbosacral kinematics over an upright and parallel spread fence

2019 ◽  
Vol 15 (1) ◽  
pp. 55-67
Author(s):  
V.A. Walker ◽  
S.J. Dyson ◽  
C.A. Tranquille ◽  
J.B. Tacey ◽  
R.C. Murray

Jumping mechanics have been investigated at take-off, flight and landing, mainly in reference to the limbs with limited evaluation of the thoracolumbosacral region. The objectives of this study were to investigate head, neck, thoracolumbosacral and limb angles in a group of experienced showjumping horses (competing at 1.20-1.60 m) over an upright and parallel spread fence. Ten horses in active showjumping training were recruited (mean 8 years old). High-speed videography (240 Hz) was used to determine thoracolumbosacral kinematic variables of the approach and take-off. No significant differences between the upright and parallel spread fences were observed for any of the variables measured. Individual horse review showed that neck-trunk, thoracolumbar, lumbosacral, coxofemoral angles, take-off distance and speed patterns at take-off were consistent among horses and also repeatable between fence types. Head-neck, stifle and tarsal angles had great variability among horses. The main limitation of this study was that only 2D motion analysis was carried out. In conclusion, analysis of individual horse patterns showed that head, neck, back and limb angles were repeatable over submaximal upright and spread fences in ten horses. Some angles were consistent among horses, but others had individual horse variation.

2010 ◽  
Vol 42 ◽  
pp. 686
Author(s):  
Nidhi Gupta ◽  
Govindasamy Balasekaran ◽  
Visvasuresh Victor Govindaswamy

Author(s):  
Thomas Quercetti ◽  
Andre Musolff ◽  
Karsten Mu¨ller

In context with disposal container safety assessment of containers for radioactive waste the German Federal Institute for Materials Research and Testing (BAM) performed numerous drop tests in the last years. The tests were accompanied by extensive and various measurement techniques especially by instrumented measurements with strain gages and accelerometers. The instrumentation of a specimen is an important tool to evaluate its mechanical behavior during impact. Test results as deceleration-time and strain-time functions constitute a main basis for the validation of assumptions in the safety analysis and for the evaluation of calculations based on finite-element methods. Strain gauges are useful to determine the time dependent magnitude of any deformation and the associated stresses. Accelerometers are widely used for the measuring of motion i.e. speed or the displacement of the rigid cask body, vibration and shock events. In addition high-speed video technique can be used to visualize and analyze the kinematical impact scenario by motion analysis. The paper describes some selected aspects on instrumented measurements and motion analysis in context with low level radioactive waste (LLW) container drop testing.


Author(s):  
Kyungsoo Kim ◽  
Jun Seok Kim ◽  
Tserenchimed Purevsuren ◽  
Batbayar Khuyagbaatar ◽  
SuKyoung Lee ◽  
...  

The push-off mechanism to generate forward movement in skating has been analyzed by using high-speed cameras and specially designed skates because it is closely related to skater performance. However, using high-speed cameras for such an investigation, it is hard to measure the three-dimensional push-off force, and a skate with strain gauges is difficult to implement in the real competitions. In this study, we provided a new method to evaluate the three-dimensional push-off angle in short-track speed skating based on motion analysis using a wearable motion analysis system with inertial measurement unit sensors to avoid using a special skate or specific equipment insert into the skate for measurement of push-off force. The estimated push-off angle based on motion analysis data was very close to that based on push-off force with a small root mean square difference less than 6% when using the lateral marker in the left leg and the medial marker in the right leg regardless of skating phase. These results indicated that the push-off angle estimation based on motion analysis data using a wearable motion capture system of inertial measurement unit sensors could be acceptable for realistic situations. The proposed method was shown to be feasible during short-track speed skating. This study is meaningful because it can provide a more acceptable push-off angle estimation in real competitive situations.


SMPTE Journal ◽  
1983 ◽  
Vol 92 (7) ◽  
pp. 729-734
Author(s):  
James A. Bixby

2010 ◽  
Vol 46 (9) ◽  
pp. 547-554
Author(s):  
Idaku ISHII ◽  
Toshikazu OKUDA ◽  
Yuman NIE ◽  
Takeshi TAKAKI ◽  
Kensuke ORITO ◽  
...  

Sign in / Sign up

Export Citation Format

Share Document